Search Documents

By R. D. Brown

This Bureau of Mines report describes a new methodology for identifying and sorting scrap metals using two modern portable instruments: a thermoelectric sorter and a hand-held emission spectroscope. The method, tested on a 27-sample stainless steel and superalloy array, makes it possible to group and/or identify a typical mixture of high-value metal scrap in two or three steps, whereas as many as seven or eight steps are needed to perform the same separations using chemical spot tests. A portable fluorescent X-ray analyzer identified 19 of the 27 alloys in the sample array by name or type; these alloys are included in the microprocessor memory. The remaining alloys were identified by using the analyzer in its elemental analysis mode and comparing the results wit.h alloy specification chemistry.

Jan 1, 1984

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By P. H. Francis

In This report, factors which currently enter into the design, manufacture, and quality assurance of explosion-proof enclosures are reviewed, with special emphasis given to the sealing concepts and sealants/cements, per se, for lenses. The physical and mechanical properties of a number of representative sealants and adhesives are measured, and found to exhibit great variance, with few discernible trends which might afford a firm base on which to establish minimum property standards. Accordingly, acceptance criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure rather than upon the minimum mat real properties of its constituents. Procedures or surface preparation of adherends, and for quality assurance, also are proposed.

Jan 1, 1980

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By Richard A. Dick

In this report commercial blasting compounds are classified according to their nitroglycerin (or equivalent explosive oil) and ammonium nitrate content as dynamites, gelatins, blasting agents, military explosives, and blasting , accessories. The ingredients and more significant properties of each explosive are tabulated and briefly discussed. Data are summarized from various handbooks, textbooks, and manufacturers' technical data sheets, together with the author's personal experience; however, this report is not intended to be a technical handbook, since it does not deal with blasting techniques. Instead, it seeks to acquaint the reader with the great variety of explosives, available, their advantages and disadvantages, and their general areas of application. Properties discussed are weight strength, cartridge strength, detonation velocity, density, detonation pressure, water resistance, and fume class. The weakness of the strength rating system and the importance of detonation pres- , sure, density, and detonation velocity in rating explosives are discussed. The terms "blasting agent" and "slurry," which are often misused, are defined. Trends indicate that blasting agents (that is, blasting mixtures with none of of the ingredients singly classified as an explosive), particularly high-density slurry blasting agents, will dominate the explosives field in the future.

Jan 1, 1968

By W. L. Crentz

In Fayette County, the Pittsburgh bed has been the major source of production for almost two centuries. Although historical documentation is not available, there is evidence, that the Pittsburgh bed may have been discovered in Fayette County near Mt. Braddock, Pa., as early as 1753. The earliest known reference to coal in western Pennsylvania was recorded in 1758 by a Quaker trader, James .Kenny, who reported having seen coal in Fayette County. The production of coke from Pittsburgh coal was begun in 1841, when two 10-foot beehive ovens were erected in the Connellsville region to make coke .for shipment by river to the market. The Connellsville, region extends from Latrobe, Pa., in Westmoreland County to South of Uniontown, in Fayette County. Connellsville coke was used with great success in the Clinton furnace in 1859.

Jan 1, 1951

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By Albert L. Toenges

This paper is the fourth of a series5/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. Many inquiries have been received regarding methods of extracting pillars with mechanized equipment, and this paper deals primarily with this phase of mechanical mining. Some of the questions that have been asked are:

Jan 1, 1942

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture fillings and associated alteration on the mechanical behavior of rocks. Experimental results are presented for 98 specimens from the Climax mine, which were tested since the annual report (May 1973). The conclusions reached are based on both these results and those reported in the annual report. The locations studied are the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from: 1) Climax, medium-grained granite, fine-grained granite, granite porphyry, schist, and gneiss; 2) Henderson, rhyolite porphyry; 3) San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineralogy, composition and fabric of fracture fillings, density, apparent porosity, and optical diffraction patterns. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic velocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Conclusions are that some relation appears to exist between compressive strength and the following properties and features for all specimens: dynamic Young's modulus, sonic velocity, density, rock composition, slope of velocity curve, composition and fabric of fracture fillings-veinlets, and apparent porosity. There appears to be some relation between compressive strength and Shore scelerscope hardness for the quartz monzonite (San Manuel). A relation appears to exist between texture and compressive strength and the extent of failure on fracture fillings for schists, gneiss, and fine-grained granite (Climax). The amount of swelling clays (montmorillonite, hydromicas, etc.) present in the rock and the relative number of fractures in which they constitute of major portion of the fracture fillings are related to the strength of the rocks. Possible tests for checking the amount of these clays present is presented including saturation, dyes, and X-rays. A useful index relating to rock strength, as revealed in this study, is the presence of swelling clays in detectable abundances. These clays can be detected in the field with a simple wetting and striking test; in the laboratory they can be detected by X-ray and dye methods.

Jan 1, 1974

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By Gordon Bath

During the summer of 1946, the Division of Geophysical Exploration of the U.S. Bureau of Mines established several primary magnetic base stations near important iron-producing districts in Minnesota, Michigan, and Wisconsin. Stations were located in groups of four to six in six separate base-station areas, and each position was marked with a concrete monument. Differences in magnetic intensity between stations in these areas, as well as the difference between each area and a magnetic datum at the magnetic observatory of the Coast and Geologic Survey at Cheltenham, Md., were measured with a modified Askania magnetometer. Measurements also were made with a Hotchkiss superdip to study the usefulness of the stations for the calibration of instruments of this type. The work was planned and supervised by F. W. Lee, chief of the Division of Geophysical Exploration, and Edward F. Fitzhugh, Jr., chief of the Minneapolis Division of the Bureau of Mines. Special mention is due Harold B. Ewoldt, Bureau of Mines engineer, for his assistance in the field work, especially in locating and establishing monuments. Special mention also is due Clyde L. Holmberg, of the Bureau of Mines, for the magnetic measurements made with the Hotchkiss superdip. Helpful suggestions were received in the field from H. L. James, of the U. S. Geological Survey. Acknowledgment is made of the cooperation of Stephen Royce, Irving E. Beckwith, Arthur Johnson, and Josiah Royce of Pickands, Mather & Co., and A. E. Matson, of Butler Bros. The U. S. Coast and Geodetic Survey furnished daily magnetograms from the Cheltenham Magnetic Observatory as well as calibration equipment and values of absolute magnetic intensity. Short-term forecasts of ionospheric conditions were obtained from the National Bureau of Standards.

Jan 1, 1951

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By John C. Cook

Channel sand bodies ("wants" or "cutouts") are deposits of barren, hard sediments which interrupt production and pose safety hazards when encountered in underground coal mining. To locate these costly impediments to mining in advance, from the surface of the ground, the seismic reflection method is recommended. High-resolution (high frequency) techniques for shallow seismic exploration of coal beds have been worked out and are reported here, including a field example. Newly-developed high-frequency, digital recording equipment was used, together with light-weight shot-drilling equipment and a variety of down-hole seismic impulse sources. Techniques for rapid but complete coverage of a coal prospect area with a crew of 2 to 6 men n 2 or 3 vehicles are described in detail.

Jan 1, 1976

By G. E. McElroy

The purpose of tins paper is not to present new date on the pressure losses due to bends and chances of area in mine openings through which air flows, but rather to correlate existing data, determined mainly on small duct systems and expressed in a variety of ways, according to uniform methods that facilitate their use in pressure-loss computations. These are required in such, air-flow problems as determining the quantity that will flow through is mine openings under a certain pressure difference or, conversely, the pressure difference that will be required to maintain a certain rate of flow. Air flowing through h ducts, such as mine airways, encounters resistance to flow due to interference of the individual air streams with each other caused by the wall surfaces. The result is that part of the kinetic energy of the flowing stream is converted to heat; and constant renewal of the kinetic energy from the total energy of the flow is required to maintain it. This process manifests itself by a decrease of the total pressure (static pressure plus velocity pressure; of the air in the direction of flow; in order that flow pray occur, there must necessarily be a differences in total pressure between the two cads of the air-ay equivalent to the pressure losses occasioned by the flow, which automatically adjusts itself in magnitude to the pressure difference maintained.

Jan 1, 1932