Search Documents

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

By Charles Vaught, Kathleen M. Kowalski

Safety and health professionals from all sectors of industry recognize that training is a critical element of an effective safety and health program. A major concern in the mining industry is how to train both an aging workforce and the expected influx of new miners and mine managers as older workers retire. Thus, a review of some of the basic principles of adult learning may be helpful to mine trainers. This paper discusses the principles of adult learning based on research in education and psychology. It stresses the importance of taking a systems approach to training, focusing on the relationship between the environment and technology, and understanding how workers interact with both. The authors argue that the principles of adult learning and a systems approach are fundamental to the delivery of effective training in the mining industry. Examples of training programs developed by the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health are presented within two broad performance domains: routine and nonroutine skills. Basics of curriculum development are also briefly presented to provide the mine trainer with a template for program development.

Jan 1, 2002

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors' quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By Frank L. Hess

"New England" and "granite" if not synonymous are at least associated terms. Where there are granites that are not deeply eroded there are usually pegmatites, the most erratic of rocks, and of them New England has a full portion. Many of the New England pegmatites contain the rare alkalis - lithium, rubidium, and cesium. however, the same in homogeneity of the earth's crust that has made the New England pegmatites unusual, in that so many of them contain the rare alkalis, has likewise made the distribution of the rare-alkali minerals sporadic even in those pegmatites, and most contain only enough to furnish collectors with more or less ornamental and uncommon minerals. New England has long had numberless collectors of minerals, and the mineralogists of its various schools have published many papers on the pegmatitic minerals, including those of the rare alkalis, but none of the papers have dealt with estimates of quantities. In this paper we have tried to place the emphasis on quantity rather than on mineralogy.

Jan 1, 1943

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

By Alvin Schallis

The. problem of supplying enough magnesia for the American war effort has become highly important. Before hostilities began, only about two-thirds of our, require vents came from domestic sources; now they must supply almost all the magnesia we need. A further burden is placed upon our own supply by the fact that more and more magnesia is being required, not alone to pace the war tempo of general industrial activity, but also to replace chrome ore in refractories and to make magnesium metal. The domestic magnesite and brucite industry is equipping itself to satisfy much of this greater demand for magnesia, but the remainder must be obtained elsewhere. The principal sources of magnesia are magnesite, brucite, dolomite or high-magnesium limestone, natural brines, sea water, salt-works bitterns, magnesium silicates, and magnesium salts. Although dolomite is tae subject of this paper, it should be considered in perspective with all these highly competitive sources of magnesia.

Jan 1, 1943

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By Charles Will Wright

The purpose of this paper is to present briefly certain preliminary results of the study of mining methods by the United States Bureau of Mines; to show the relative importance of each method in terms of tonnages mined and man-hours consumed; to give to the mining engineers and particularly to the young student of mining a better understanding of the principal mining methods; and to indicate changes now in progress and to present suggestions for improvements in the art of mining. Questions of mine development and details of underground practice such as drilling and blasting, loading, hauling, hoisting, ventilating, pay systems and mine management are omitted, as these have been or will be discussed in other bureau publications.

Jan 1, 1931

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young&apos;s modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0&apos; and c&apos;. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By John Rusnak, Christopher Mark

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load frame and point load testing of coal measure rocks in six states. More than 10,000individual test results, from 908 distinct rock units, were used in the study. Rock lithologies were classified into general categories and conversion factors were determined for each category. This allows for intact rock strength data to be made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).