Search Documents

By Frederick H. Raab

The electromagnetic retransmission system is a new, automated method of locating trapped mine workers. This technique overcomes many 1 imitations inherent in electromagnetic direction finding by reducing the effects of the conducting ground to an acceptable maximum, by finding position accurately in the presence of antenna tilt, and by eliminating the need for the receiver to be located directly above the subsurface transmitter. Three transportable three-axis magnetic-dipole transmitters on the surface create a system of electronic grids in which the phases of the downlink Signals convey position information. The subsurface retransmitter modulates the uplink carrier of the existing beacon transmitter with the received downlink signal; the coal-pillar loop antenna is used for both receiving and transmitting. The uplink receiver uses a three-axis antenna and extensive digital signal processing. A small computer integrates data, estimates position, and controls system operation through VHF-FM communications. Both coal-mine and deep-mine operation are possible by selecting appropriate transmitting power and signal frequencies. This report shows such systems to be both feasible and practical.

Jan 1, 1980

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By Levent Ozdemir

A 6-ft. diameter laboratory tunnel, raise and shaft boring machine was designed and constructed to carry out research investigations to enhance the performance of mechanical rock excavation equipment. The machine is operated with a computer control system and features extensive instrumentation to monitor and record various test parameters, including tri-axial cutter forces, machine thrust, torque, rpm and penetration rate. An extensive laboratory testing Program has been conducted using this machine, demonstrating the feasibility of attaining high rates of penetration in various sedimentary geologies. Also, a large data base has been developed to serve as a basis for the improved design and performance of tunnel, raise and shaft boring equipment.

Jan 1, 1986

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By R. R. Sayers

"The number of investigations reported during the past year indicates that control of the health hazard due to abnormal air conditions is still a matter of serious consideration in the mining, metallurgical, and allied industries.Australia. - In an investigation into the health and working conditions of employees in the mining industry of Tasmania and Victoria3, it was found that although pulmonary tuberculosis may occur early in life, silicosis is e disease of slow evolution and does not appear frequently under the ace of 40. A period of at least ten years in the industry was found necessary to produce silicosis, and in no case was the disease found in those who had not worked underground. A very high incidence of silicosis was found in all fields among those who had worked underground 20 years and longer. There was some evidence that silicosis complicated by tuberculosis may occur earlier than uncomplicated silicosis.England. - In a paper presented before the Section on Occupational Diseases of the British Medical Association, Dr. E. L. Middleton, the medical inspector of factories, called attention4 to the occurrence of silicosis in various industries throughout the country.punitive on some quite harmless industries. Thus Middleton says: ""Where the amount of dust is small the action of the phagocytes is likely to be effective, but where it is great . . ."" What dosage is indicated by ""small"" and ""great"" in this connexion? If the meaning of ""small"" were known, would it be correct to go on to say, as he does, ""each successive dose of silica produces a summation of effects""? Then, again, would it be fair to say ""a comparatively brief period of exposure may be the only determining factor""? What, in minutes, hours, or days per week, per month,' or year, is intended by ""a comparatively brief period""? ""Intermittency of the process"" is another expression used in summing up the reasons for and against a standardization of air purity by a gravimetric process or enumeration of the particles; the arguments against such a standardization are, by Middleton, considered strong, but they are by no means convincing to us. A standard has been accepted in respect of the amount of lead in milligrams per 10 cubic metres of air; Dr. Ronald Lane showed in another paper read that adherence to this makes the occurrence of poisoning highly improbable. Mavrogordato has placed on record figures of silica dust at different stages of the improvements in the workings of the Rand mines, and such a control is in constant operation in them today.We emphasize these points because apparently the Government has taken the unusual course of legislating first and postponing inquiry to a later date, as in the ""Various Industries (Silicosis) Scheme, 1939."" The insurance companies also have a considerable interest in the matter of compensation for the silicosis risk. Where exposure - as in the refractories industries, the grinding industries, sandstone industry, and pottery industry - is day in and day out, they rightly demand a premium far higher than for any other disease scheduled under the Workmen's Compensation Act - 5 per cent on the wages bill. row every industrial employer, such as the paint and varnish manufacturer, who has a sack of crushed silica in his store .room, from which he extracts once a week enough to make a paste With spirit and add to his other ingredients in order to give them the necessary ""bite,"" becomes involved, and may have to abandon the use of the material or pay 8 per cent on his wages bill for an absolutely negligible risk.. For meting out justice standardization seems urgently called for."

Feb 1, 1930

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By H. S. Kennedy

THE HELIUM ACT (50 Stat. 885; 50 U. S. C. 161,163-166), as amended, places the responsibility for conserving, producing, and selling helium upon the Secretary of the Interior, acting through the Bureau of Mines-the only producer of helium in quantity in the world. It operates 4 plants-I each at Amarillo and Exell, Tex.; Otis, Kans.; and Navajo (Shiprock), N. Mex. The demand for helium has increased steadily since the decline immediately after World War II and is expected to exceed the capacity of the present plants in the near future. The Congress has appropriated $6,000,000 far constructing a new plant. In addition to providing additional capacity to meet increased demands for helium, the new plant will enable the Bureau of Mines to better conserve the helium in, the Government-owned reserves at Amarillo and Navajo.

Jan 1, 1958

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese-grade ore 6/ from the wide-spread domestic manganese and manganiforous iron deposits. Samples for testing were received from the Interstate Manganese Co. in northeastern Tennessee, 11 miles west of Mountain City and 10 miles southwest of Damascus Va. The ore deposit occurs in the residual material of the Shady dolomite 7/ as an unconsolidated mixture of hard and soft manganese oxides and clay.Numerous tunnels and pits have developed a large reserve of ore in an area of about 15 acres. One pit 250 by 50 by 20 feet is being mined by rower shovels. The ore is hauled to a washing plant for log-washing, hand-sorting, and jigging. Coarse concentrates from the washing plant are marketed without further beneficiation.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. F. Fisher, who made the roasting and magnetic tests."

Mar 1, 1942