Search Documents

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Stephen Gerard Sawyer

This report presents a Fortran IV computer program for the structural analysis of space-frame protective canopies used in underground mines to protect equipment operators from falls of roof, face, or rib. This program entitled CANOPY permits rapid calculation of the elastic strength of a canopy for a variety of static loading conditions. Stresses in, and displacements of each structural member are computed and printed out. Additionally, identification of all members that have commenced yielding, weight of the canopy, total loads on the canopy, and maximum loads that the canopy can sustain elastically are output. Program description, input instructions, program listing, and two example problems are included.

Jan 1, 1972

By G. E. Geiger

The purpose of this research was to develop a computer simulator fur predicting the air quality in existing coal mines as well as a design aid for developing new mines. In addition to the air quantity flow, the other variables of tempera Lure, moisture, methane and respirable dust are necessary to determine the air quality. An additional feature of this simulator is that it allows parametric studies of these variables to explore the effect that these variables have on the air quality of an operating mine system. The research has also pointed out arias where more research is needed, and promote better and more systematic data taking techniques. Wang and Hartman (see Reference 9, on page 1-98 of Section 1) had already published a computer program to determine the ventilation of large mines, and Wang and Saperstein (see Reference 10 on page 1-98 of Section 1) later published a refinement of the work in the previous reference. These references were the starting point of the simulator developed by this present research effort, and Section 1 of this report is a slightly modified version of the original vent elation program. The modifications were necessary to permit the additional programs of temperature-moisture, methane and dust to be

Jan 1, 1972

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By James W. Hendrix

A survey of endomycorrhizal fungi occurring on orphan coalmine lands in Western and Eastern Kentucky revealed a great diversity of species present. Thus a large number of fungi are available for isolation and evalution for enhancing revegetation of mined land. Endomycorrhizal fungi isolated from orphan mines stimulated growth of sweetgum seedlings on mine soil at low fertilisation but inhibited growth at high fertilization; this growth inhibition at high fertilization did not occur with plants growing on peat-perlite. Banding of endomycorrbizal inoculum was not advantageous, compared with incorporation of inoculum throughout the growth medium, for production of mycorrhizal sweetgum seedlings. Newly reclaimed mine spoils were nearly nonmycorrhizal, compared with land reclaimed four or eight years earlier. A procedure for isolation of single-spore cultures of endomycorrhizal fungi was developed; this procedure is necessary for studies of ecotypic variability. A practical procedure using container-grown Pisolithus tinctorius-infected shortleaf pine seedlings for production of large numbers of bareroot pine seedlings infected with P. tinctorius for mined land reclamation was demonstrated.

Jan 1, 1982

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By Rudolf E. Greuer

Two computer programs for the real-time calculation of concentration distributions in the ventilation system of underground mines were designed. They allow one to simulate the movement of fumes or other contaminants with the ventilating air, the calculation of concentrations at any given point and time, and the determination of the total contaminant exposure at different places in the mine. Multiple and time variable contaminant sources can be handled and recirculation is no obstacle. The, first program is based on an airflow distribution which has, in the input data, to be stated. The second program has been linked to in existing program for the calculation of airflow distributions. Two versions of this second program are provided to accommodate the two existing programs. Several executed examples demonstrate the program performance.

Jan 1, 1981

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a single subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although

Jan 1, 1943

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By J. G. Donaldson

Nickel containing less than 0.01 percent of total metallic impurities was produced at the Rolla Metallurgy Research Center of the Bureau of Mines by electrodeposition from purified electrolytes. The first report on this research4 described purification of electrolytes by selective precipitation and by liquid-liquid extraction. This second report describes a procedure: or electrodepositing high-purity nickel from electrolytes purified by passing a nickel ammine solution through a column of an ion exchange resin. The nickel electroplated directly from the ammine solution without further treatment; a titanium cathode and two platinum anodes were used. The nickel deposit was dense, smooth, and adherent, and contained less than 0.001 percent each of cobalt, copper, and iron, and spectrographically detectable traces of aluminum, magnesium, and silicon. Nonmetallic impurities in the nickel metal were carbon and sulfur, each present in concentrations of less than 0.01 percent. The results of several experiments planned to purify solid nickel salts by zone refining are also reported. These salts, after purification, were intended for use in preparing electrolytes for deposition of high-purity nickel. Results were not encouraging so that the more promising ion exchange procedure was emphasized chiefly.

Jan 1, 1962