Search Documents

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By Ricardo Gaviria, Vincinte Acosta

There are major blast design and field procedures differences between conventional blasting in horizontally bedded coal seams and blasting underneath coal seams in a multi seam deposit with seam inclinations of 14 degrees or more.

Jan 1, 1995

By James Tarr, Matthew Eichler, Brent Tardif

ANFO was being used as one of the blasting agents on a construction site in New England. Groundwater was encountered in numerous blast holes. The blasting contractor was employing typical explosives loading procedures for wet conditions. An abutter to the project complained that blasting caused her well water to have an odd taste and smell. Through testing, it was determined that there were hydrocarbons and nitrates in the well water. Several days later a second neighbor complained of foul tasting water; again it was determined that hydrocarbons and nitrates were present.

Jan 1, 2003

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By G. Gomez Ciments-Calcia

The sources of complaints by neighbours of the operating quarry are due to the 3 following causes : - Impulsional noises or air hoch wawes – Vibrations - D u s t How a blasting in a quarry operation is felt by neighbours cannot be measured solely by the various limits set by national and European regulations regarding vibrations and air shock waves (sound pressure).

Jan 1, 2002

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Robert Hopler

As a part of the depression and rectification work on the Port Morris branch of the Harlem Division of the New York Central & Hudson River Railroad, a short tunnel is being driven under St. Mary’s Park. The park is near 149th St. and St. Ann’s Ave., in the Borough of the Bronx, New York City.

Jan 1, 2006

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By Rowan A' Murry Karstel

One way to ensure dragline productivity is by Increasing the size of the dragline bucket. In August 1994, Optimum Colliery in conjunction with Van Reenen Steel, Northwest Applied Technology, SSAB of Sweden and Barlows Equipment launched the new lightweight dragline buckets. Optimum built the first prototype bucket that was used for the deslgn for future buckets. After knowledge had been gained from measuring the input force of the bucket Northwest Technologies designed the new bucket with finite element analysis. Together with the knowledge of quenched and tempered steel from SSAB of Sweden and Barlow Equipment, the new Wrightech bucket was born.

Jan 1, 1998

By James Goldberg, Mark Withey

The Material Service Thornton quarry is a multi-million annual production tons complex. Surrounded by busy surface highways, and divided by a railroad on the north/south axis and further divided by a major interstate highway on the east/west axis, blasting is a daily challenge. This paper deals with the problems of production blasting in an area adjacent to that interstate highway, and paralleling a busy four-lane highway. Discussion includes primary blasting issues such as borehole size, drill patterns and flyrock controls. Discussion also includes blast designs, timing schematics, smooth-wall blasting solutions, traffic and vibration concerns and many other factors influencing the success of this project.

Jan 1, 2006

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By David Siskind

The authors studied small seismic exploration blasts for vibration characteristics and effects on structures in Mexico. Obtained were 267 three-component recordings of ground vibrations and structure responses from 62 test blasts at six single-story masonry structures. Charges were 4.55 kg (10 lb) of Vibrogel expolsive at depths of 20 and 30 meters. Initial blasts were 240 meters distant and proceeded towards the structures to as close as 5 meters. All blasts were in soil media in two basic types of terrain, low saturated areas and upland dry areas. Structural inspections were before, during, and after the test blasts.

Jan 1, 2002

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005