Search Documents

By Kenichiro Yamamoto, Masaharu Murakami, Toshio Matsuzawa, Yoshiyuki Ikeda

In a series of tests, we examined the dynamic shock resistance of Emulsion Explosive in water and compared it with that of Dynamite and Slurry Explosives. Both the distance between donor and acceptor charges and the delay initiation timing of the acceptor charges were varied. The resistance to dynamic shock varied with the properties of the explosive. In the case of emulsion explosives, there seems to be a certain proportional relationship between the critical detonation distance and the delay initiation timing. Some blasting results with emulsion explosives are described.

Jan 1, 1983

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013

By B. A. Cheeseman, R. Skaggs, C. F. Yen, S. Wolf

Shallow buried explosives pose a significant threat to lightweight vehicles and their onboard personnel. To date, designers of lightweight vehicles are limited in their knowledge of what occurs during the blast. The high intensity, short term loading imparted by the explosion is enormously complex and can be significantly affected by a number of parameters including the size, shape, type, detonation point and depth of burial (DOB) of the explosive and the type, density and water content of the soil. Recent advancements in numerical simulations have enabled the complex blast event to be accurately modeled by coupling Eulerian and Lagrangian analyses: the former is well suited to modeling the blast and while the latter, the structural response. Further validation of the modeling technique is considered in the current paper, which details simulations performed utilizing the coupled Eulerian-Lagrangian analysis to the study the blast output of explosives buried in saturated sand. These experiments varied explosive charge size, its depth of burial, the target stand-off (SO) distance and target plate dimension. The investigation concludes with a discussion of the accuracy of the numerical simulations when compared with the experimental observations.

Jan 1, 2005

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Michael E. Curtis

This paper outlines a study performed to analyze the advantages of utilizing a blasting agent with a velocity of detonation that is 1.3 to 1.4 times the P-wave velocity of sedimentary shales and sandstones at a major Midwest coal operation.

Jan 1, 1997

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By Raymond H. Green, Mitchell W. Green

The authors examined the application of precise millisecond delay electric blasting at a well-known Vermont quarry. The paper explains how the use of a new high-accuracy electric delay detonator has improved fragmentation, raised productivity 10%, simplified blast design, and increased the ability to predict results from blasting.

Jan 1, 1986

By Rodger Andrews

High cost - low productivity mining methods at the Homestake Mine forced the need for a new and safer means of ore extraction. Vertical Crater Retreat (VCR) was introduced in 1978 and accounts for over 50% of the underground mine production today. Many advantages can be attributed to this form of "bulk mining"; including steady production, decreased labor costs, and the ability to mine bulk stopes in the lower portion of the mine. However, safety and high productivity are the two major advantages. This paper will deal specifically with crater blasting and the application of mass blasting techniques in Vertical Crater Retreat slopes.

Jan 1, 1988

By Rene A. "Moose" Morin, Craig Copping

Innovative concepts in drilling and blast design have been used to remove deteriorated concrete and have enabled contractors to reduce costs and time on St. Lawrence Seaway rehabilitation projects. Time is of the essence on these contracts since the Seaway system is only available for this work during the winter freeze up. Unique electrical sequential initiation systems and specially modified drilling equipment have been used to accurately remove a narrow slice from the 83 foot high lock walls. These new methods successfully reduced demolition time, minimized overbreak and adhered to strict vibration limits.

Jan 1, 1986

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Thomas Palangio, Blessing Taiwo

Image-based fragmentation analysis is increasingly utilized in blasting operations to evaluate particle size distribution in a non-intrusive and efficient manner. However, the accuracy of optical granulometry systems can vary significantly with particle size. Higher precision is typically achieved for larger fragments, generally those greater than golf ball size when using drone-based orthomosaic analysis. In contrast, the detection and delineation of fine particles become less reliable due to constraints such as pixel resolution, particle overlap, and partial burial within the muck pile. This variability does not undermine the value of image analysis but rather highlights the need for a deeper understanding of its operational thresholds and the integration of complementary methods or calibration approaches to improve its reliability across the entire particle size distribution. Technologies such as WipFrag, originally developed in the 1980s, are designed to conduct in-situ fragmentation analysis within complex blast environments, where fines are often obscured by larger fragments. The challenge becomes more significant in blast rounds exhibiting wide gradation ranges and increased fines, particularly resulting from excessive energy concentration in high-pressure zones near the borehole. Previously, this issue was addressed through methods such as analytical correction, zoom-merge correction, and empirical calibration using Rosin-Rammler and Swebrec distribution models. However, these traditional empirical calibration approaches, particularly those tied to distribution functions like Rosin-Rammler have shown limitations, especially in accurately representing the fine region of the fragmentation curve. In contrast, the recently developed xP-fan model, which incorporates the relationship between powder factor and fragment size, introduces the fragmentation energy fan principle which Kuz-Ram model does not entail. This paper presents a study on the application of the novel xP-fan calibration to enhance the accuracy of optical granulometry systems. The findings demonstrate how xP-fan help calibrate the fine region of the PSD without deflecting the maximum size.

Jan 26, 2026

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

By J P. Tidman, I J. Kirby, G H. Harries

The SABREX computer model is based on the fact that both shock waves and gas pressure are important in describing a blast. The treatment of explosive-rock interactions includes the influence of non-ideal detonation to make use of recent advances in that field. Details of the blast layout are defined from a comprehensive list of conditions the blaster can control (drill pattern, charging and hook-up). The program gives practical and graphic information about fragmentation, muckpile, damage and costs.

Jan 1, 1987

By Oldrich Machacek, Gary R. Eck

The underwater detonation test method has been long recognized as a useful tool for the evaluation of the energy release and relative effectiveness of commercial explosives. In this study, underwater energy tests were performed for emulsion and watergel commercial explosives in comparison with ANFO. Heavy ANFO type blends based on emulsions and watergels were also investigated under and without confinement.

Jan 1, 1990

By Richard Dooley

This paper is one sided because it presents the problem, but not the solution. The problem of blisters (bubbles) and occasional tears in caisson liners occurred when blasting and we have not found a conclusive cause nor a preventive solution. (For back ground information, consult Techniques of Precision Blasting in the Excavation of Drilled Piers, by George Mosteller at the Sixth Conference on Explosives & Blasting Technique in Tampa, Florida 1980).

Jan 1, 1983