Search Documents

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Harry L. Siebert, Thomas Gelormino

Rock excavation in urban areas occurs with maximum public exposure and, with the aid of explosives, is one of the challenges facing this industry today. Such excavation is also a hidden factor in areas of new growth, revitalization or upgrading existing facilities in or near urban areas.

Jan 1, 1985

By Ronald R. Rollins

A continuous propagation velocity measurement probe has been utilized to determine velocities of slurry explosives, whole prills, crushed prills, aluminized crushed prills, in bulk and plastic screw tubes.

Jan 1, 1984

By Carl Hendricks

AQUILA Mining Systems Ltd. is the world leader in drill monitoring, control and GPS based drill navigation systems for the mining industry. This paper will review the general design and application of AQUILA.s drill systems currently in use throughout the world and the key benefits that derive through their use.

Jan 1, 2002

By William H. Snyer, Victor A. Sterner

A cache of buried explosives was discovered by ICI Explosives, USA Inc. at one of their sites near Gillette, Wyoming. An intensive investigation conducted by ICI management indicated that nitroglycerin sensitized dynamite might be present. Information also indicated that up to 20,000 pounds of explosives may have been buried.

Jan 1, 1997

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Roger Lucas, Dale Nies

The McLaughlin Mine is an open-pit disseminated gold mining operation. Homestake Mining Company's approach to solving some of the blasting problems inherent to this type of deposit provide an interesting case history. Geology, although unique and site specific, is overall similar to other mines within the Western United States over-thrust belt and demonstrates an excellent example of the blasting conditions and requirements common to most of these operations.

Jan 1, 1990

By Edward J. Walter

Vibration control is affected by many factors which are difficult to isolate and evaluate. Occasionally a circumstance occurs in which one factor appears to predominate and its effects can be evaluated. Changing rock characteristic or lithologic variation is one of these factors or parameters. In a recent seismic monitoring project, lithologic variation in the form of hard lenses occurring suddenly and randomly in the rock to be excavated caused sudden and large increases in vibration level. Data are presented to illustrate these effects, and procedures used to control these effects are described.

Jan 1, 1981

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990

By E. Contestabile, B von Roser

Schedule IV containers in Canada and IME- containers in the United States have made possible the transport of mixed loads. That is, using these containers for detonators, one can simultaneously transport detonators and explosives on the same vehicle. As a result of a recent accident, the Canadian Chief Inspector of Explosives asked for a review of the appropriateness of the Schedule IV container in its present use. The Canadian Authority asked for a re-assessment of the adequacy of the Schedule IV container in preventing propagation of a reaction from the detonators in the container to the remainder of the explosives on the truck, and its ability to contain fragments generated by the detonators. A series of tests was performed to determine the initiation threshold temperature for non-electric detonators and the failure threshold temperature for the shock tube to establish some guidelines for preventing communication from one case of detonators to another within the transport container at elevated temperature. Tests fell into the following categories: inter-case sympathetic detonation, detonator thermal auto-initiation, shock tube thermal sensitivity, and intra-case sympathetic detonation. The results indicate that temperature is a critical factor, which determines to what extent, if any, communication occurs.

Jan 1, 2002

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007

By Manuel Villalobos Calderón

This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important drawbell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

Feb 1, 2020

By Manuel Calderón

Chile is responsible for 30% of the global copper production; the world ́s largest. However, significant challenges are faced in this industry; declining grades (1.13% in 2002 to 0.61% in 2015), high cost of energy, scarcity of water, and environmental concerns. Mining trends suggest the future of the industry will be focused in the underground space, specifically due to the depletion of economically viable surface mineral deposits. For example, the largest block cave mineat Codelco ́s Chuquicamata mine is expected to reduce energy costs by 50% and dust emissions by 97%compared to the open cut mine. To access these underground deposits, critical infrastructure is required; horizontal tunnel developments, extraction levels, vertical raises, and ore passes with the on-time delivery of the highest quality outcomes being a requisite for successful project delivery (Lift 1 of 3 at Chuquicamata Underground has over 1000drawbells).One aspect that makes this scenario even more challenging for deeper underground operations is the increased risk profile (people, equipment, and geotechnical) that forms part of the general environment. Furthermore geotechnical risks should be considered and they include rock burst and windblast. The safe interaction with this environment must be sustainable throughout the full life of the project. This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important draw bell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025

By Carlos Pañura, Michael Geldres, Alejandro Rojas

The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration.

Feb 1, 2020