Search Documents

By Gregory Lorsbach, Wade Hutchison, Earnest Grigoryan

Comparing measurements from multiple seismographs, particularly when the instruments are deployed in a “side-by-side” situation, is often problematic. Measurements often differ by as much as a factor of two. These differences are attributed to issues related to calibration, geophone coupling, and differences in geology over very short distances. Unfortunately, these explanations are often purely qualitative, but are accepted as factual. Shake table testing often demonstrates that those seismographs that indicate large differences for a particular vibration event, may correlate within a few percent of each other and the known shake table input. Geophone coupling also does not fully explain the difference in measurements since geophones in side-by-side measurements are deployed identically. Differences in geology do not explain the difference in measurements since it would be unrealistic to expect significant differences in distances less than one meter in a normal monitoring situation. Utilizing a new technological approach to vibration measurement and analyzing numerous side-by-side measurements, it has become clear that a significant portion of the observed differences between seismograph measurements are instrumentation induced. This study examines and describes some of the most significant sources of the seismograph error budget.

Jan 1, 2005

By Jair Alarcón, Lucas Steffen, Leopoldo Muñoz

Flyrock is one of the most significant hazards associated with blasting in open pit mining, especially for blasting operations near communities. Flyrock can lead to severe injuries, fatalities, and property damage, compromising the license to operate. For this reason, defining exclusion zones is critical to ensure the safety of people and equipment. A very large radius will reduce the risk of flyrock; however, excessive exclusion zones can significantly impact the productivity of the operation and, in some cases, compromise the extraction of ore in critical sectors. Many mine sites use distances derived from pre-established standards, experiences from other mines, or still use simple methods for analysis, like recording blasts with a terrestrial camera and performing deterministic calculations to determine exclusion areas, applying an arbitrarily safety factor for people and equipment. In this paper we present a new approach that allows the calculation of the exclusion zone by measuring critical flyrock parameters with a high degree of accuracy through a new video analytics technology, this data then is used as input to calibrate probabilistic flyrock models to have more robust calculations, allowing optimized and safe exclusion zones. The proposed methodology leverages high-accuracy data and continuous monitoring to dynamically adjust D&B designs and exclusion zones, ensuring maximum safety without unnecessarily restricting operational efficiency. A case study is presented where the application of these new digital technologies allows precise prediction and control of flyrock trajectories, enhancing the accuracy of exclusion zone boundaries. In this case we successfully reduced the exclusion zone radius to 100m, allowing the ore extraction in a critical region close to the community safely. The study shows notable improvements in safety and productivity, including zero flyrock incidents and enhanced protection for nearby communities. The adaptive nature of these digital tools offers scalable solutions for various blasting environments. The paper concludes by recommending the integration of these tools into standard blasting protocols, highlighting the potential for widespread adoption in the industry to mitigate flyrock risks effectively.

Jan 21, 2025

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By Carlos Agreda

A general review of the comminution theory and also the general differential equation of the comminution are described, analyzed and discussed in order to be applied to rock blasting. Some size distribution functions are reviewed and discussed to determine which of them represents better the cumulative low size distribution F(x) as a function of the nominal particle size (x), for the rock blasting fragmentation. Based on the mathematical comminution model before presented a formula to calculate the burden (B) is developed and discussed.

Jan 1, 1994

By Robert Hopler

RBH Note: At the time of this price list the handwriting was already on the wall regarding the ultimate breakup of the company under the Sherman Anti-Trust Act. The brand names Atlas and Hercules, noted on page 3 of this pricelist, would become the names of the new companies created from du Pont.

Jan 1, 2012

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By Robert A. Farnfield

This paper outlines the theory behind transfer functions and illustrates their application in the prediction of structural response to blast induced ground vibration. The ability to predict the response of a structure to a recorded ground vibration is desirable for a number of reasons.

Jan 1, 1994

By Satish Kate

Mining of Iron Ore in India is done by Surface Mining methods and most of the deposits are massive and are occurring in Hills, surrounded by green forest cover. While majority of iron ore produced are from mechanized mining systems, some quantities are also produced from semimechanised mines. In mechanized mines, apart from state-of-the-art level of mechanization, the Run-off-Mine ore is subjected to multi-stage crushing, screening and washing/beneficiation, for improving the grade and ensure segregating of different size range. The steel plants within the country have been operating their own captive mines, where both lumps and fines are used in their furnaces. In case of mines, which exclusively supply ores to export market, the lumps produced yield very high price and thus efforts are being made to maximize lumps recovery. The mine, where the author had been associated, is an export-oriented mine which supplies iron-ore to Japanese steel plants.

Jan 1, 2004

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By Greg Quinn

After a long week of work in Colorado Springs this past July, I was looking forward to flying home to start a long anticipated family vacation. As I grabbed my seat on the plane, a man sitting next to me innocently inquired, to the row as a whole and not to me in particular, “I wonder what the weather will be like in Phoenix”? To most people, this is a common (maybe the most common) topic of casual conversation. To a meteorologist that just dealt with six thunderstorm delays at a major golf event over 4 days, well, lets just say the smirk on my face said it all. After giving my flight mate a detailed forecast and a short explanation on why I would know such information, I sensed, correctly, the inevitable follow up question was coming. “Why would you need a meteorologist at a golf tournament?”

Jan 1, 2012

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By Robert Hopler

Torpedoing Wells. – On the completion of the drilling, or when the production is found to decrease, it is usual to “torpedo” the well to increase the flow. This process was patented in 1862 by Colonel Roberts, who believed, with many others, that the oil was contained in crevices in the rock, which might not have been tapped by the bore-hole. He therefore proposed the use of nitroglycerine, gunpowder, or other explosive, to break up the rock at the bottom of the well, so that these rich “pockets” might be brought into communication with the well.

Jan 1, 2007

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007