Search Documents

By X. Cui

Hydrocyclone is widely used in closed-circuit grinding process. However, in the first classification operation of coarse particles with high pulp density, the shortcomings of traditional cyclone are that the grinding cycle load is much high, the apex of cyclone is easily to be blocked and classification efficiency is less. Specifically, the problems of traditional cyclone used in grinding process are as follows: (1) Mill utilization factor is low and its handling capacity is small. (2) Coarse particles mixing in cyclone overflow affects the following separation process and fine particles mixing in underflow causes over-grinding, which affects the total recovery rate of valuable minerals. (3) High grinding cycle load leads to large amount of high-density slurry pumping, which causes high energy consumption and severe wear of cyclones, pipelines and pumps. The applications of new type pre-classification hydrocyclone with centrifugal volute in the first classification process of Iron Mine Mill are introduced in the paper. Pulp particles fed in the centrifugal volute were arranged in advance, so that coarse particles can be far away from the overflow pipe, which can reduce the short circuit current to avoid coarse particles entering overflow and improve classification efficiency and accuracy of cyclone. The strong points of the new cyclone in the coarse classification operation are as follows: (1) finer overflow and less fine particles mixing in underflow improves classification efficiency more than 10%; (2) lower ball mill load cycle improves ball capacity more than 10%;(3) grinding energy consumption reduces by more than 20% and cyclone feed pump reduces energy consumption by more than 12%. In short, new type pre-classification cyclone with centrifugal volute solves the problems of fine particles mixing in underflow, high grinding cycle load and less classification efficiency in the coarse classification operation. Therefore, it has broad application prospects in ferrous metal and non-ferrous metal ore dressing plant.

Sep 1, 2012

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

By A. V. Nguye, P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration. Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. A possible mechanism, based on the existence of the pre-existing submicron-sized gas bubbles, known as bubstons (i.e. bubbles stabilized by ions), present in water in close proximity to the hydrophobic coal surfaces is discussed in line with the early observation of flotation improvements by microbubbles “nucleating” on hydrophobic surfaces. In particular, the dependence of the bubble-particle attachment efficiency on electrolyte concentrations supports hypothesis on the salt-dependent and ion-specific existence of bubstons. However, a theoretical explanation of the transition salt concentration (at about 0.1M) is deficient at present. The existence of these submicrobubbles in close proximity to hydrophobic surfaces is not trivial. They can (as can individual gas molecules or other solutes) mediate and extend the range and magnitude of the attraction between hydrophobic macroscopic surfaces. These bubbstons may explain the curious phenomena of the socalled long-ranged hydrophobic attraction measured with the Surface Force Apparatus and Atomic Force Microscopy, and the slippage at hydrophobic surfaces. Finally, the coalescence of bubbstons affects the rupture of liquid films at a very large thickness (over 100 nm), observed, but unexpected, by flotation chemists.

Jan 1, 2003

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By R. K. Logric

Bor flotation tailings are very interesting from two reasons: first, is having due value presently, and second represent serious pollutant into this region of Balkan. This paper is only one small part of investigation about processing of valuable minerals from tailings, and desulphurization of this biggest pollutant in the same time, by refloating. The main objective of this work is to pay attention on this problem for resolve greatest environ-mental problem of Serbia and Balkan in the nearly future. Bor is potential regional risk spot, since that failure of its tailings dams would release high amounts of toxic materials that would reach the Danube River. The basic goal of this experimental investigation was finding some possibility for flotation tailings treatment by classical froth flotation. In order was obtained material effect through copper recovery, and environmental protection by moving the rest of reprocessing into the safe place. The work present obtained results of laboratory tests in two laboratories: laboratory of mineral and recycling technology at the faculty in Bor, and laboratory of department of mineral processing of ITNMS in Belgrade.

Jan 1, 2014

By L. M. Sun

Baotou Baiyunerbo Mines Location in Inner Mongolia is a famous deposit of iron mineral and rare earth mineral accreting. The iron ore has very complicated ingredients and minerals composing. In the mine, there is not only magnetite ore but also hematite ore, so that it is impossible for high grade iron concentrate to adopt single wet low-intensity magnetic separation or high-intensity magnetic separation to concentrate iron mineral. Because of mixing the magnetite with hematite mineral in feed ore, recovery of iron of magnetite production system in the mineral processing plant is less than other mineral processing plants. Therefore, the research for increasing recovery of iron of the magnetite production system in the plant was undertaken. The paper presented the research for using dry magnetic separation to increase recovery of iron concentrate of the magnetite production system in the plant. It mainly includes dry magnetic separation test and wet magnetic separation and reverse flotation test. The test results indicated that dry magnetic separation is a important way to improve the feature of feed ore of the magnetite production system and to increase the recovery of iron. The recovery of iron may increase from about 70% to over 80%. The research also presented optimum operation parameters of the dry magnetic separator and the separation flowsheet. In conclusion, using dry magnetic separation to treat with feed ore of the magnetite production system in the plant to increase the recovery of iron is a feasible technique. The research present a new way for the mineral processing plant to made technology innovate to increase the recovery of iron concentrate of the plant in future.

Jan 1, 2014

By U. Dmitrakova, G. Sedelnikova, D. Kim, E. Savari

"The paper presents the results of research on the development of gold and silver extraction technology from refractory gold sulphide flotation concentrate of one deposits of Nord-East of Russia. The concentrate is due to the complex mineral composition. Gold and silver are finely disseminated in sulphide minerals (arsenopyrite and pyrite partially oxidized by 7-11%). These are characterized by high content of silver 219 g/t and sulphide sulfur 32%, the presence of poorly soluble silver minerals (silver sulfosalts, fahlore, finely dispersed hypergenic acanthite in iron hydroxides and jarosite, etc.), and impurity minerals capable of interacting with cyanide (pyrrhotite, marcasite, nonferrous sulphides) and causing higher than normal cyanide consumption. Pretreatment of refractory sulphide concentrate by biooxidation using a mixed association of mesophilic and moderately thermophilic bacteria at a temperature of 36-40 °C for 120 hours oxidized arsenopyrite by 97.5%, pyrite by 93.5%, unlocked refractory gold, and generally oxidized the minerals absorbing cyanide and oxygen before cyanidation. Further oxidation of these minerals-absorbents was facilitated by the aeration in calcareous medium of the solid biooxidation residues of the concentrate. Sorption cyanidation of the solid biooxidation residues with addition of lead (II) of recovered 91.2% of gold and 82.9% silver from biooxidation residue, compared with 80.1% and 46.6%, respectively, for sorption cyanidation without the preceding biooxidation step. Biooxidation of the concentrate prior to cyanidation improves the recovery of precious metals, especially silver, and significantly reduces cyanide consumption from 18.7 kg/t to 3-5 kg/t of concentrate. INTRODUCTION Biooxidation of gold sulphide concentrates using acidophilic microorganisms has been successfully applied worldwide (van Aswegen et al., 2007; Gericke et al., 2009; Sovmen et al., 2007; Sovmen et al., 2009). At least 15 full-scale plants for tank biooxidation of sulphide concentrates are presently in operation, and the construction of new ones is planned (Bulaev et al, 2015)."

Jan 1, 2018

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By A. Shibayama

Soil contamination by organic compounds is one of the most concerned issues on polluted soil. It is well known that there are limited methods to remediate the contaminated soil on site. Especially, the in-situ method for contaminated soil is too difficult to de-contaminate the organic pollutant. In this study, the fundamental ability of soil remediation, which aimed to decrease oil concentration in, in-situ process, have been researched by using a high pressure gas generated from ?crush composition? on artificially oil contaminated soil. The n-hexadecane (n-C16H34) and other organic compounds were selected as soil oil contaminators, gravimetric analysis by soxhlet extraction and GC-MS were used as qualitative and quantitative analysing methods. For the experimental examination, the influences on the difference in the concentration of n-hexadecane (and other organics), the tamping amount, position and repetition of crush composition in soil, and scale (size) of experimental model were investigated. The n-hexadecane concentration reduced by the explosive effect of crush composition showed a reasonable decrease of about 30 wt%~60 wt% compared to the initial n-hexadecane. The removed amount of n-hexadecane and distance from explosion point of the crush composition was related in scale and model of contaminated soil.

Jan 1, 2014

By C. L. Tang

Parts of the wastewater are reused directly and the rest moderately purified and reused, so the utilization rate of wastewater of the whole processing plant reaches 100 percent. At the same time, beneficiation indicators have been improved stably, and great economic and social benefits have been achieved.

Jan 1, 2014

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014