Search Documents

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

Taknar polymetal (Cu-Zn-Au-Ag-Pb) deposit and concentration flotation plant are located in the northeast of Iran. The flotation feed contains Chalcopyrite, sphalerite and pyrite with 4, 4 and 8 percent respectively. Cu and Zn contents are 1.26 and 3.5 present. Pyrite decreases the quality of base metal concentrates and increases the amount of sulfur compounds produced in the base metal extraction processes. Therefore, depression of pyrite is essential in the concentration of base metal sulfides by flotation. For flotation tests, 4 mixed collector systems, MIBC (20g/t), lime and tow depression systems (sodium cyanide (60g/t)-zinc sulphate and dextrin (300g/t)-zinc sulphate) were used as collector, frother, pH regulator and pyrite-sphalerite depressants in the chalcopyrite flotation stage, respectively, and SIPX, MIBC, lime and copper sulphate (as activator) were used in sphalerite flotation from first stage tailings. The results have shown that, sodium cyanide is a suitable depressant for pyrite and sphalerite in the first stage of flotation. Compared to dextrin as depressant, chalcopyrite recovery was decreased approximately 1.83%. In addition, when sodium cyanide was used as pyrite depressant, copper sulphate consumption raised approximately 90 g/t for activation of sphalerite. From Environment and HSE points of view, dextrin is natural, biodegradable, and non-toxic while cyanide is very high toxic. Keywords: sequential flotation, Cu-Zn massive sulphide, pyrite depressant, dextrin, cyanide

Sep 1, 2012

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By S. Groudev

Acid drainage waters generated in the uranium deposit Curilo, Bulgaria, were treated by means of a pilot-scale passive system consisting of a permeable reactive multibarrier and a constructed wetland connected in a series. The multibarrier had a total volume of 23 m3 and consisted of an alkalizing limestone drain and an anoxic section for microbial dissimilatory sulphate reduction, bio-sorption and additional chemical neutralization. The waters had a pH in the range of about 2.5 ~ 4.0 and contained radionuclides (uranium, radium), heavy metals (copper, zinc, cadmium, lead, nickel, cobalt, iron, manganese), arsenic and sulphates in concentrations usually much higher than the relevant permissible levels for waters intended for use in agriculture and/or industry. The water flow rate through the multibarrier varied in the range of about 1 ~ 17 m3/24 h, reflecting water residence times of about 300 ~ 18 hours. An efficient removal of pollutants was achieved by the multibarrier during different climatic seasons, even during cold winter days at external air and water temperatures close to 0oC. The multibarrier effluents were enriched in dissolved organic compounds and in some cases still contained manganese and iron in concentrations higher than the relevant permissible levels. These pollutants were removed in the constructed wetland as a result of the activity of different heterotrophic microorganisms, including some bacteria able to oxidize the bivalent manganese and iron ions to Mn4+ and Fe3+, respectively.

Jan 1, 2014

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper contains description of research results of technology development for copper recovery from weathered tails of iron processing plant. The predominant host mineral that contains valuable component is chalcopyrite occurring in its free form and in associations with ore and rock-forming minerals. Copper grade is 0.26-0.30%. Emulsion inclusions of chalcopyrite in pyrite and sphalerite were noted. Major problem is low copper recovery (30-35%) by flotation. When studying chalcopyrite in primary concentrate it was determined that the surfaces of many chalcopyrite grains are covered with oxide films which prevented collector attachment onto them. Second issue was deep association of chalcopyrite with pyrite and sphalerite. Sulfidizing reagent addition did not help to reach the required level of copper recovery to concentrate. In the result of research performed the technological flowsheet was developed including preliminary treatment of head material in a special unit aiming at oxide films removal, followed by copper rougher flotation on head size tails, crude concentrate regrinding and a number of cleaner flotation operations. After the treatment of weathered tails according to the flowsheet developed, copper recovery to flotation concentrate became 71.53%, at 23.46% copper grade. The suggested technology allows one to solve the issue with treatment of technology-related copper-containing stockpile material, as well as to include the ores where copper is represented by sulfide minerals covered with oxide films into processing."

Jan 1, 2014

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

By L. Simpson

South African is a repository of significant deposits of a variety of minerals. The Citigroup confirms this assertion with an estimate of in-situ valuation of US$2.5 Trillion. The mining sector plays an important role in the South African economy. In addition to the mineral resource base South Africa has other comparative advantages. Firstly, South Africa retains major mining companies that participate globally, including Anglo American, Goldfields and De Beers. Their global involvement offers much to the local mining sector and the broader economy. Secondly, government established research councils. The Council for Geoscience (CGS) was established to manage the Geological Survey of South Africa, including the reduction of geo-scientific investment risk. The Council for Scientific and Industrial Research (CSIR) promotes industrial development, including mining technology development. Mintek undertakes mineral research from mineral examination of ores, to extraction and refining technologies and manufacture of end products. Thirdly, South African universities teach and conduct research along the mineral value chain. They have increased their minerals graduates? capacity, thus advancing knowledge and skills. Knowledge and technical progress are behind productivity growth and emergence of competitive advantage. The research and development (R&D) capabilities of industry, science councils and universities, working in unison, will enhance the competitiveness of the South African mining industry. The National System of Innovation (NSI) requires multi-disciplinary, collaborative research. Key R&D elements, including skills and expertise, funding and facilities, must be available to implement a long-term national strategy or programme. Improved international collaboration and partnerships between government, academia and industry driven human resource development (HRD), ultimately develop the critical mass for inter-generational skills requirements. This trend requires an expansion of research collaboration programmes. Decisions involving investments and collaborative actions pertaining to R&D in the sector necessitate an analysis of the South African mineral value chain R&D capability. This paper analyses the evolution of R&D capability from exploration to refining, tertiary education, science councils and industry. The political economy of the evolution of this capability is analyzed in relation to the central role that the South African government plays in creating an appropriate supporting environment and related initiatives to enhance R&D and innovation. Keywords: research and development (R&D), science councils, universities, industry, innovation policy, South Africa

Sep 1, 2012

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

This paper presents a theoretical investigation on the ionic equilibrium of Fe(III)?Ni(II)?H2SO4?H2O system. A non-ideal speciation model is developed to calculate the concentration distribution of iron and nickel species in a mixed ferric and nickel sulphate aqueous solution over the pH range from 0 to 4 and temperature from 25 to 100°C. A series of speciation diagrams for iron and nickel species is plotted with the effects of ionic strength and temperature on the equilibrium constants being taken into account. The ionic strength-dependent equilibrium constant is treated through a semi-empirical Vasil'eV equation, which is based on an extended Debye?Hückel theory. A Helgeson model is applied to extrapolate the equilibrium constant to elevated temperature. The ionic equilibrium reactions are described by a group of numerical equations containing the temperature and ionic strength-dependent equilibrium constants, which are solved by the Newton-Raphson method. The speciation model is also applied to estimate the hydrogen ion activities and corresponding pH values. The calculated pH values are in agreement with the experimentally measured pH, and are compared to literature data and pH values produced by the Visual MINTEQ® program (a computer code for the calculation of chemical equilibrium in natural aqueous system). This investigation provides a deep insight into the ionic equilibrium behavior of a mixed metal sulphate aqueous system which commonly occurs in hydrometallurgical processing. Keywords: speciation, chemical modelling, thermodynamics, iron, nickel

Sep 1, 2012

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By C. Dorfling

Experimental work was performed using a bench scale autoclave to evaluate the effects that leaching temperature, pressure, initial acid concentration, and the solid to liquid ratio have on the behaviour of base metals and platinum group metals in a high-pressure sulphuric acid oxygen leaching system. The concentrations of metals in the leach solution were measured over time at different leaching conditions. At the conditions investigated, the initial acid concentration had the largest influence on the copper leaching kinetics, while the leaching rates of the other precious metals (OPMs: rhodium, ruthenium, and iridium) were highly dependent on the leaching temperature. A set of chemical reactions that can be used to describe the leaching chemistry was proposed, and the associated reaction kinetics were quantified. As a first estimation, the rate expressions were considered first order, and the rate constants were determined using the method of least squares, considering the experimental and predicted concentrations obtained for the different leaching conditions. Of the OPM compounds, the sulphides showed the fastest dissolution rate, followed by OPM alloys, and finally the OPM oxides. During the initial leaching stages, base metals and OPMs competed for the available dissolved oxygen, with oxygen being preferentially used for copper leaching. Precipitation of OPMs during the initial leaching stages can be ascribed to copper and nickel dissolution according to exchange reactions between dissolved OPMs and copper present as digenite or nickel present as polydymite. Control of the autoclave residence time is of particular importance to enhance the selectivity of this leaching step, given the dependence of the PGM leaching rates on the extent of copper dissolution.

Sep 1, 2012

By W. Y. Liu

A sulfate reducing bacteria strain (named SRB-A) is isolated from sanitary wastewater by using anaerobic technology of Hungate. The studies of physiological, biochemical and phylogenic of the isolated strain are carried out. The colonies of the strain are circle. Cells that are slightly curve, rod-shaped with the size of 1.0~3.0µm in length and 0.8~1.0µm in width. The optimum temperature for growth of the organism is 30~35°C. The optimum pH for growth is 7.0~7.2. Strain SRB-A can use sodium lactate, sodium citrate, sodium acetate, ethanol and acetone as electronic acceptor but can not use glycerol, glucose, sucrose and sodium oxatate. The isolated strain reduces sulfate, sulfide, sulfur, DSMO and FeCl3, then nitrate and nitrite can not be used. The strain has higher tolerance of NaCl, and the optimum growth occurs in the presence of 5%~8% (w/v) NaCl. The result of 16S rDNA sequence analysis indicates that the isolated strain SRB-A is the most similar to Desulfo-vibrio halophilus, and the level of the similarity was 98.4%. The isolated strain has a stronger ability to reduce sulfate, and the level of sulfate reduction reaches about 90% at pH 7 in the liquid medium. 0.6 to 0.8 is the optimum COD/SO42- in the medium for the isolated strain to show better ability to reduce sulfate. At pH 2.5 the level of removal of Cu2+ reaches 96.3%. Under the condition of pH 3.5, the level of removal of Zn2+ reaches 92.6%. When the value of pH reaches about 7, the Fe3+ is precipitated by the formation of Fe(OH)3, and Fe3+ is removed up to 89.4% at last.

Jan 1, 2014