Search Documents

By Takaaki Wajima

The slag was attempted to be converted into the adsorbent for phosphate removal from aqueous solution using the alkali fusion method. The slag was mixed with NaOH powder (NaOH / Slag = 1.6), and then the mixture was heated at 600 ? for 6 h to prepare the precursor. The precursor was stirred at room temperature in distilled water to synthesize the adsorbent, and the removal ability of the obtained adsorbent for phosphate from aqueous solution was investigated. The products, including hydrocalumite and calcite, were synthesized, and the removal efficiencies of the adsorbent for F- and PO43- showed higher than those of raw BF slag, especially removal of PO43- are excellent (99 %), while the removal of Cl- , SO42-, NO3- and Br- was minor. The adsorbent could remove PO43- selectively in the co-existing solution of Cl-, NO3-, F-, SO42- and Br-.The equilibrium adsorption capacity of the adsorbent for PO43- was extrapolated using Langmuir and Freundlich models, and experimental data are found to fit Langmuir than Freundlich. The calculated maximum adsorption capacity of the adsorbent for PO43- is higher than other adsorbent reported previously. The high affinity of the adsorbent for PO43- in aqueous solution was caused by the formation of hydroxyapatite [Ca5(PO4)3(OH)] and brushite [CaHPO4?2H2O]. The prepared adsorbent is expected to be anew inorganic adsorbent for the removal of phosphate ion from wastewater. Keywords: Blast furnace slag, Alkali fusion, Phosphate removal, High selectivity

Sep 1, 2012

By P. Altinkaya, O. Celep, H. Deveci, E. Y. Yazici

"Copper-bearing gold ores have proved difficult to treat in conventional cyanide leaching process owing to prohibitively high consumption of cyanide by readily soluble copper minerals interfering with gold extraction. Cyanide leaching of gold from copper-rich ores can be improved by intensive cyanidation or application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting and leaching). In this study, nitric acid leaching of a copper-bearing pyritic concentrate (0.3% Cu, 62 g/t Au and 110 g/t Ag) as pre-treatment prior to cyanidation was investigated. The mineralogical analysis of the concentrate has revealed that it is composed of mainly quartz (25%), pyrite (32.7%), sphalerite (5.37 %), galena (2.12 wt %) and anglesite (1.13 %). Arsenopyrite, chalcopyrite, covellite and bournonite were also detected as minor phases present. Previous studies carried out by the authors showed that direct cyanidation (1.5 g/L NaCN) of the as-received concentrate (d80: 80 µm) produced low gold (45% Au) and silver (46% Ag) extractions. Nitric acid pretreatment of the as-received concentrate was performed for 5 hours at 1-5 M HNO3 and 80oC. In these tests, 65% Cu/Pb and 94% Zn were leached. The nitric acid pre-treatment improved the extraction of gold and silver in subsequent cyanide leaching (1.5 g/L NaCN) to 82% Au and 87.5% Ag with a concomitant decrease (up to 54%) in cyanide consumption. It can be inferred from these findings that the removal of copper from the concentrate and the liberation of the occluded gold by nitric acid leaching as pretreatments can be appropriately employed for the treatment of the copper-bearing pyritic concentrate with high gold/silver content. INTRODUCTION Refractory ores are often characterized by their low amenability to cyanide leaching resulting low (often <80%) Au/Ag extractions (Bhappu, 1990; Celep et al., 2009; Marsden and House, 2006). One of the most common causes of refractoriness is the physical or chemical encapsulation of submicroscopic or fine-grained gold in sulphide minerals such as arsenopyrite and pyrite (La Brooy et al., 1994; Vaughan, 2004). To render refractory gold ores/concentrates amenable to cyanide leaching, the decomposition of sulphide minerals within a pre-treatment process to expose the encapsulated gold grains to the action of cyanide is required. In this regard, roasting, pressure oxidation and biooxidation are commercially used processes for pretreatment of arsenopyrite/pyrite gold ores/concentrates ahead of cyanide leaching (La Brooy et al., 1994). Presence of cyanide-soluble copper minerals in the ore leads to low gold recoveries and high cyanide consumptions under conventional cyanide leaching conditions. High cyanide concentrations (CN:Cu>4) should be employed to achieve high gold recoveries from copper-rich gold ores/concentrates. This may require recovery of cyanide from effluents. In this regard, SART Process (sulphidisation-acidification-recycling-thickening) employed industrially for recovery of cyanide and copper as a by-product. This process simply relies on the addition of sulphide (as Na2S, NaSH or H2S) to the leach solution prior to the acidification to pH 4-5. This results in the precipitation of copper as Cu2S and occurrence of free cyanide which is recycled to the leaching circuit after S/L separation (Dai et al., 2012)."

Jan 1, 2018

By S. Jeon, N. Hiroyoshi, N. Kitajima, S. Tanaka, M. Ito, R. Pongsumrankul, C. B. Tabelin

"Gold (Au) extraction is inefficient when crushed waste mobile phones (WMPs) are directly leached by ammonium thiosulfate likely because of the cementation/precipitation of dissolved Au in the presence of base metals like copper (Cu), iron (Fe) and/or aluminum (Al). This study applied physical separation techniques to remove base metals as well as plastics and concentrate the Au containing fractions from WMPs prior to leaching. Coarse fraction of crushed WMP (+2-5.6 mm) was pretreated by jig and magnetic separation to remove plastics and base metals like Fe, Cu, and Al, while the fine fraction (-2 mm) was pretreated by flotation, and float and sink separation. The leaching results showed that Au extraction increased in both of the size fractions. In the coarse fraction, Au extraction increased by as much as 2-fold after pretreated (from 4 to 7%). Improvement of Au extraction in the fine fractions after pretreatments were even more dramatic. Au extraction increased from 4 to 61%. These results indicate that physical pretreatment to remove co-existing common metals and plastics is effective to improve Au extraction from WMPs. INTRODUCTION Global sales of mobile phones are expected to increase steadily in the foreseeable future because a lot of people buy newer phones with upgraded and more advanced functions almost every two years, which leads to the higher generation of waste mobile phones (WMPs). WMPs contain a wide variety of materials including plastics, glasses, base metals and precious metals such as gold (Au). Among all the valuable materials in WMPs, Au accounts for over 80% of its total metal price (Park et al., 2017), so recovery of Au from WMPs is needed."

Jan 1, 2018

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By S. H. He

This paper focuses on the influence of pulp oxygen content on the separation of pentlandite and pyrrhotite contained in two different process streams in the Clarabelle Mill, operated by VALE INCO. The two process streams are (i) the scavenger cleaner feed, the product of regrinding the thickened, scavenged concentrate and the B cleaned tail produced from treating the non-magnetic fraction of the milled run of mine ore, and (ii) the magnetic concentrate which is the magnetic fraction of the milled run of mine ore. In the Clarabelle Mill, sulphite (SO32-) and TETA (triethylenete-tramine) are together used to selectively depress pyrrhotite from pentlandite. These depressants pre-ferentially decompose collector and/or sulphur enriched species at the pyrrhotite surface, an appar-ently essential mechanism in pyrrhotite depression from the scavenger cleaner feed stream. Selectivity in depression may originate from differences in the electrochemical rest potential of pyrrhotite and pentlandite. As both minerals are susceptible to oxidation, aeration in conditioning and flotation plays a key role in selective flotation. Important differences in the flotation behavior of pentlandite and pyrrhotite from the magnetic concentrate and the scavenger cleaner streams are highlighted in

Jan 1, 2014

By Zofia Swierczek

This paper reports the results of a detailed mineralogical study of typical, low-grade Australian nickel laterite run-of-mine ores. Successful development of an effective beneficiation process for upgrading such low grade laterite ores relies on good knowledge of the laterite mineralogy and the value metal(s)? distribution characteristics. Both QEMSCAN and quantitative X-ray diffraction techniques were used to conduct the mineralogical analysis of three types of laterite ores, and the results were compared with those obtained by chemical analysis. Some of the major challenges faced included accounting for the mismatch between the nickel values measured by QEMSCAN and those recorded by chemical analysis. This was primarily due to the relatively low concentration of nickel in the ores and its wide dissemination among several major host minerals in complex association. Careful analysis showed that the limit of nickel detection in iron oxide host mineral grains under normal operating conditions was around 4%. Keywords: nickel laterites, mineralogy, characterisation, QXRD, QEMSCAN

Sep 1, 2012

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By E. Isokangas

The production of minerals for economic use is a two-stage process, involving mining to extract the mineral from the ground, and processing to convert the mineral into a marketable product. Generally, mining and processing have been viewed as self-contained entities. Both have separate objectives, separate cost centres and key performance indicators (KPIs) that do not reflect the customer/supplier relationships that inherently exist. However, mining and processing operations are inter-connected and therefore intimately inter-related with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often misses potential economic benefits and energy savings. During the past fifteen years, the authors have been involved in implementing a holistic methodology ?Mine to Mill Process Integration and Optimisation (Mine to Mill PIO)? to maximize the overall profitability of the operation rather than just optimizing any individual process in a mining operation. Metso Process Technology and Innovation (PTI), along with their project partners, have conducted several projects to significantly increase their production- generating typically 5% to 20% higher throughput and improve the overall mine and concentrator performance through PIO methodology. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG, HPGR or conventional grinding circuits. This paper explains the Mine to Mill PIO methodology and discusses the benefits of such an approach on the energy consumption, the overall costs and benefits of mining operations. The paper also summarizes several case studies illustrating the use of PTI methodology in a variety of applications. Keywords: integration, optimization, simulation, modeling, mine-to-mill, comminution, blast, drill, crushing, grinding

Sep 1, 2012

By C. Hazotte, M. -O. Simonnot, V. Houzelot, B. Laubie, M. Guilpain, B. Jally

"More than 400 plants in the world are able to accumulate nickel (Ni) in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, Ni can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and producing metal. It has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Hydrometallurgical processes have been designed; two different pathways were developed: i) acid leaching of ashes after biomass combustion and ii) direct Ni water extraction after biomass grinding. Experiments with 2 species of Ni hyperaccumulators (A. murale from the Balkans and R. bengalensis from Malaysia) have shown that the first process is very robust and transposable. For the second one, the way Ni is stored in the plant has a strong influence on extraction. A. murale transformation was explored in more details from the lab scale to the pilot scale. Results proved that Ni is totally transferred into the aqueous phase after 2 hours at 90 °C. A life cycle assessment has clearly shown the environmental interest of this approach (especially by detoxifying agricultural soils). INTRODUCTION Agromining is an emerging phytotechnology aiming at recovering metals thanks to hyperaccumulating plants (van der Ent et al., 2018). These plants are able to accumulate very high concentrations of metal in their aerial parts. For example, for nickel, the hyperaccumulation threshold is 0.1%, i.e. 10 grams of metal per kilogram of dry biomass. There are some advantages to use this technology instead of conventional mining techniques: •,Treating unconventional metal resources: they can be (i) natural soils with low concentrations but also low fertility because of the metal presence (like serpentine soils for Ni) (Bani et al., 2015), (ii) mine tailings or (iii) industrial wastes (like surface treatment sludge) after soil construction (Rue, 2017);"

Jan 1, 2018

By A. Deepatana

This study compares the use of an aminophosphonate chelating resin Purolite S950 and a sulphonic acid strong cation exchange resin Purolite C160H to recover nickel and cobalt from the synthetic bioleach solutions. Batch adsorption of metal citrate is performed as a function of metal citrate concentration (15~2000 mg/L) and solution pH (0.01M and 0.1M citric acid). The adsorption mechanism as inferred from the fit to Langmuir (LM), Freundlich (FM) and Redlich-Peterson (RP) models demonstrates that nickel citrate adsorbed onto C160H appears monolayer in comparison to that adsorbed onto S950 exists multilayer. In contrast, cobalt citrate adsorption onto both C160H and S950 agrees with the LM model. The results have shown that loading capacities of nickel and cobalt citrate onto C160H are 60 and 65 mg/g whereas those observed onto S950 are 16mg/g and 6 mg/g respectively. These are achieved in metal citrate prepared in 0.1 M citric acid. Resin regeneration is conducted in using 2 M nitric acid solution. The results show high efficiency of nickel and cobalt citrate elution from Purolite C160H. Findings from this study suggest Purolite C160H is a suitable adsorbent for recovering nickel and cobalt from bioleaching solutions.

Jan 1, 2014

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014