Search Documents

By J. R. Woolsey

In late 1988, the Committee for Coordination of Joint Prospecting for Mineral Resources in South Pacific Offshore Areas (CCOP/SOPAC), Suva, Fiji, consulted the Continental Shelf Division of the Marine Minerals Technology Center regarding low-tech, low-cost, reconnaissance sampling systems for a variety of nearshore needs. Materials of interest to several member island nations included silica and calcareous aggregate for cement manufacture, sand for beach replenishment, heavy minerals, and precious metals. A principal criteria of the system was that it be of low-tech design, and as far as possible, suitable for construction on the islands from available materials. It should also be operable with SOPAC personnel on island vessels of opportunity. The system selected to satisfy these requirements was a convertible drill of basic airlift design, capable of operating with easy modification as either a vibralift or airlift, depending on the desired application. The basic system included a drill pipe constructed of heavy duty 76 mm (3") black iron pipe, divided into three 3 meter sections (for ease of transport), fitted with an air intake manifold and bit at the lower end. A 25 mm (1") galvanized pipe assembled in three similar sections and clamped to the drill pipe served as a water jet to assist in cutting. Air was supplied to the manifold by means of a 12 mm (1/2") pipe also clamped along the length of the drill pipe. Suitable hoses supplied water and air to the upper ends of the respective pipes by means

Jan 1, 1989

By Robert M. Owen

Geochemical exploration for marine placers involves the acquisition, processing, and interpretation of geochemical data. Recent technological advances such as in-situ analysis systems and microcomputers have greatly improved our ability to acquire and process data, but their full benefits cannot be realized until we also develop improved methods for reducing and interpreting large amounts of raw geochemical data. Toward this end, our research has sought to identify existing and/or develop new geostatistical techniques for use in marine placer exploration. Each technique has been tested by evaluating its performance in the analysis of existing data sets. The data sets typically include the results of chemical analyses of suites of sediment samples collected from areas of known or suspected platinum and gold placers along the Bering Sea coast of Alaska. Results to date indicate that three geostatistical methods (subpopulation partitioning analysis, comparative factor analysis, and end-member compositional factor analysis) are useful in identifying elemental groups which can serve as "pathfinders" in the search for marine placers, and are also helpful in discerning the generic geochemical basis under lying observed statistical correlations between pathfinder elements and placer minerals. Existing methods of modelling sediment dispersal patterns have been examined with a view toward adapting them to the specific problem of understanding placer formation in

Jan 1, 1986

By William D. Siapno

The International Marine Minerals Society has now come of age! Previously known as the International Marine Mining Society, it was an informal group without officers, by-laws or official status. Despite the lack of formal structure, the Society has cosponsored symposia both in Europe and in North America including the 16th Annual Underwater Mining Institute in Halifax, Nova Scotia, last year. The roster of members is now sufficient to emerge as a fledgling professional society. To this end an ad hoc committee was appointed to prepare by-laws stating the objectives of the Society, provide the procedures for the election of officers and other guidelines essential for the operation of the organization. This paper briefly summarizes the history of the group, the by-laws, together with membership requirements.

Jan 1, 1986

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speeds (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion.

Jan 1, 2003

By John Noakes

Marine scientists at the University of Georgia, have in the past few years, designed, developed and refined two geochemical survelliance systems for the exploration of hard mineral resources on the seafloor. The one first developed is an underwater sled which contains a nuclear radiation detector for measuring naturally occurring gamma radiation that is associated either with marine phosphorites containing uranium and its decay daughters or thorium decay products that are indicative of monzanite. The latter can, in most instances, be used as a pathfinder mineral for placer deposits that may contain other heavy minerals of interest such as rutile, ilmenite, chromite, gold, etc. This sled is operational in continental shelf depths. The second system is capable of more definitive measurements in the form of direct elemental analyses of the silt and clay fractions within the surficial sediments. It consists of a towed sled containing a submersible pump which, upon agitating the sediments, transfers the finer fraction up a hose to a shipboard centrifugal cone then to an automated sample processor. The resultant samples are rendered into sediment wafers, suitable for non-destructive XRF analysis. The system is capable of shipboard analysis for specific elements within minutes after sampling, allowing a cursory look upon which an exploration grid can be formulated while on site. A much wider spectrum of up to 40 elements can be evaluated when the wafers are returned to the land based laboratory.

Jan 1, 2011

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speed (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion. AUV control system (CS) has tri-level structure to allow a motion in a rugged seabed terrain. According to the generally accepted categorizations, CS includes execution, coordination and strategic levels. The strategic level contains the goals of AUV mission. Obstacles avoiding and route choice are realized by means of simultaneous maneuver in vertical and horizontal planes. Sonar system is used for data acquisition about obstacles. It consists of a few echo-sounders with fixed directivity pattern. The route choice algorithm operates at two lower levels of CS. Basic (?reflex?) functions of spatial motion are realized within the execution level and considered in the paper. The choice of motion modes is carried out at the coordination level of system. All accessible navigating information (the data from flight sensors and from multichannel echo-sounder systems) is used for this purpose. In addition the bypass of characteristic types of obstacles is carried out with the help of basic motion modes combination. The modeling results of bypass of various typical obstacles, and also their combinations are described in the paper.

Jan 1, 2011

By James E. Dailey

Marine mining is driven by profitability, and profitability is driven in turn by people and equipment that can work productively and safely at sea. Design challenges faced by the marine mining community have much in common with those faced by the offshore construction community. Technical solutions continue to move freely between both communities. A brief pictorial history summarizes the evolution of offshore construction technology as it grew in the Gulf of Mexico and expanded worldwide. Attention is focused on those areas of platform and pipeline construcion where there is potential technology application to underwater mining. An especially difficult challenge faced by both communities is work in the surf zone. Some innovative concepts for surf zone construction operations are presented and possible applications to marine mining are suggested.

Jan 1, 1989

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By W. D. Siapno

Marine mineral resources have been reviewed in great detail on numerous occasions over the past few years. A summary of these efforts would indicate there is little new on the horizon as far as economic programs are concerned. Deep ocean minerals, though not forgotten, hold little promise for development in the immediate future, i. e., manganese nodules, cobalt crusts, polymetallic sulfides, etc. Nearer to shore, within the EEZ, and particularly within waters under state control greater industrial interest is expressed. Interest in sand and gravel not only persists but is growing, dependent largely upon the construction industry. Precious metals demonstrate the greatest growth potential.

Jan 1, 1988

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By Jon Machin

?ORE? is defined as ?mineral/s that can be mined at a profit?. So, what is ORE at 2,000 m water depth? Is it 5% Copper or 1.8% Nickel/Cobalt? One of the key factors that determine what is ORE, profitable or not, is the cost of mining and extraction. Therefore a determination of ORE requires a commercial and technical appreciation of both sea bed mining equipment and mining options. Perry Slingsby Systems (PSS) have built more remotely operated submarine work vehicles, including 900HP trenching machines, than any other company. With Nautilus Minerals, PSS have been studying a range of deep ocean mining solutions. This paper discusses the commercial and technical issues of various extraction techniques applicable to deep ocean mining from 1,500 m to 5,000 m water depth. Issues such as the rate of extraction, (i.e. tons per hour) is a key economic component and is often constrained by the design and horsepower of the miner. Likewise the design itself of the mining machine and cutting heads can determine the size of material produced which impacts on methods of lifting the ore to surface. Issues such as overburden, sea floor conditions, style of mineralization and physical properties of the ore, obviously affect the selection of appropriate mining machine configuration.

Jan 1, 2004

By Tetsuo Yamazaki

Seafloor massive sulfides have been a subject of interest for profitable commercial mining these ten years. Because of the higher Au, Ag, and Cu contents, they have received much attention as immediate commercial mining targets by private companies and nations. Some of them already proposed the technologies necessary for the commercial mining. However, the technologies for survey, excavation, lifting, and ore dressing have not yet well been examined from viewpoint of the economy. In this presentation, the authors present some key factors and improvements for better economy in the mining.

Jan 1, 2010

By Frans van Grunsven, Cees van Rhee, Geert Keetels

One of the obstacles during the initial phases of project development is the assessment of the environmental impact. Mining residue, consisting of fine seafloor sediments, are to be discharged subsea to mitigate the impact of these suspended particles. In order to test the effectiveness of discharging in proximity of the seabed, a numerical model is developed within the open source software package OpenFoam. Dedicated laboratory experiments for numerical model validation are discussed within this paper. INTRODUCTION Siltation is considered one of the major pressures on the environment for a seabed mining operation. Siltation is defined as the pollution of water by a high concentration of suspended sediments like clay or silt. This can be caused by two main activities during the mining process: the spill loss during the excavation and the return flow of undesired seafloor sediment after ore filtration on the ship. In a concentrated cloud, these fine particles form a so-called turbidity plume. Prediction of the size of these plumes and the created layer thickness of deposited sediment is a crucial part of the environmental impact assessment. The challenge in predicting the behaviour of these plumes is found in the wide range of scales involved in the process. At the point of origin, the turbidity plumes spread mainly under the influence of turbulent whirls created by an initial momentum and a buoyancy difference due to the presence of the suspended sediment particles. If carried by ambientcurrents, these plumes can spread for several kilometres before blending in the background.

Jan 1, 2018

By B. J. Bluck

Diamond mega-placers, in order to rank amongst the primary diamond deposits, are defined as => 70 m carats at =>95% gem quality. There is only one mega-placer known and that is found along the coast of southwestern Africa fringing the Kaapvaal craton. Placers are classified as residual when they are left on the craton, transient when being eroded into the exit drainage and terminal. Terminal placers, in being the final depositories of diamonds off the craton, have the greatest probability of being a mega-placer and such is the case in the placer deposits near the Orange River mouth, southwestern Africa. There are four main groups of conditions leading to the development of a mega-placer: the craton, the drainage, the nature of the environment at the terminus and the timing. The craton, in its role as the producer of diamonds is significant in respect to its size, diamond-fertility, the degree to which diamonds from successive kimberlite intrusions have been retained there and their availability to the final drainage yielding the mega-placer. Cratons in being buoyant have a tendency to leak diamonds into surrounding basins but in being incompressible often have orogens converge onto them resulting in lost sediment being returned as foreland basin fills. In order to concentrate a bulk of diamonds the drainage basin has to be large with a high proportion of it on the craton. The drainage yielding the mega-placer should ideally not have been preceded by older drainage and other systems that may have robbed the craton of earlier diamonds. The exits of diamonds from the craton need to be few in order to focus on their supply and the drainage network needs to be efficient in order to remove the maximum volume of diamonds off the craton. This efficiency and the focused termination is best achieved by the rejuvenation of a pre-existing drainage network. The drainage should be young enough to yield host sediments friable enough to allow brittle diamonds to be recovered from them.

Jan 1, 2004