Search Documents

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Christian Leble, Dr. -Ing. Jakob Vogelsang, Dr. -Ing. Oksana Solt, Dipl. -Ing. Joachim Meier, Dr. -Ing. Wolfgang Orth

In the course of closing the gap between the Brandenburg Gate and Alexanderplatz, the Museum Island station was built by Implenia Construction GmbH. The tunneling for the platform hall took place on a length of about 106 m (347 ft) under the protection of a major ground freezing measure and crossed the Spree canal as well as the listed castle bridge. The approximately 20,000 m³ (4.54 E+06 US gal dry) frozen mass lay mainly in the Berlin sands. In order to ensure safe tunnelling and to protect the adjacent buildings, the planners had defined requirements for the mean freezing temperature and thickness of the frozen mass. For a reliable conclusion on the dimensions of the frozen mass, we used innovative temperature sensors as well as the new, web-based 3D measurement visualization and the associated site-specific evaluation software. The largely automated evaluation enabled a quick and reproducible determination of the temperature distribution in the frozen soil and its thickness in the relevant cross-sectional areas. The measurements were validated by thermal calculations using the Finite-Element-Method. Thus, an objective and clear assessment basis was available to ensure rapid coordination between stakeholders. The evaluations provide new insights into the temperature influences from tunneling, the application of shotcrete and the concreting of the inner shell. The newly implemented active thawing system is also an interesting innovation.

May 1, 2022

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Antonio Kodsy, Lutful Khan

A research was carried out to test the possibility of reducing the pullout resistance of metal sheet piles driven in clay soils using Electrokinetic (EK) conditioning. The hypothesis was applying an electric gradient for a certain period of time should reduce the adhesion between the clay soil and the sheet piles. Tests were conducted on bench scale thin stainless-steel metal plates embedded in pure kaolinite clay, and mixtures of kaolinite clay and sand. The pullout resistances were determined after 20, 40, and 60 minutes residence times of steel plates in the soils before and after EK conditioning under an electric gradient of 1500 V/m. In kaolinite clay, the pullout resistance showed linear reduction with the duration of EK conditioning and about 60 % reduction in pullout resistance was observed after 60 minutes EK conditioning. For the kaolinite-sand mixtures, the pullout resistances were reduced by about 70% and 80% for 20% and 30% sand contents respectively after 20 minutes EK conditioning and showed no significant improvement with the increase in conditioning duration. It was concluded that the proposed electrokinetic conditioning process could potentially reduce the pullout resistance of metal plates embedded in clay and clayey soils. SHEET PILE WALLS Sheet pile walls are typically used at waterfronts as retaining structures or during the construction phase to shore the soil and avoid collapse of the excavations. When used as permanent structures, sheet pile walls are not removed after the completion of the project. However, as temporary support, they are extracted after the completion of the project and reused. In pure clay soils the extraction processes often becomes a challenge requiring very large pullout forces which could damage the sheet piles. There is a research need for developing an efficient method of sheet pile extraction from clay soils addressing the issue of pullout force reduction. However, very few researches have been conducted regarding the extraction techniques of sheet piles and their economic effect on the cost of a project. In this study a novel method for reducing the pullout resistance of sheet piles in clayey soils using electrokinetic conditioning was explored. The hypothesis of this research is that the electrokinetic process in soil/water system, specifically electrophoresis and electroosmosis, could be used to loosen the sheet pile walls embedded in cohesive soil and hence reduce the required force of extraction. The aim of this study was to test this hypothesis through laboratory tests carried out on steel plates embedded in cohesive soil samples. The pullout forces of the steel plates before and after varied duration of electrokinetic (EK) conditioning were evaluated and compared. The process was also investigated for clay-sand mixtures.

Jan 1, 2019

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram

A geotechnical forensic evaluation of piles for an industrial facility in Haryana was performed to assess the quality of the piles and to evaluate piles installed using two different types of rigs. Low strain pile integrity tests were performed on all piles to assess the pile length and possible presence of structural defects. Coring was done through questionable piles for the clinching evidence of concrete quality and pile length. Probe holes adjoining piles helped confirm the bulging of piles at shallow depth. The paper highlights the importance of implementing a well-planned quality assurance program to confirm that all piles installed are of the desired quality.

Sep 1, 2022

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022