Search Documents

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001

By J. E. Udd

"In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the author visited key officials and institutions in Canada, the United States, the Republic of South Africa, the United Kingdom, Germany, and Poland. Material from the Australian province of New South Wales and Hungary was also included.The report that resulted included, among other sections: (1) the history of wire ropes and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements regarding safety factors; (4) a review of the various operations and their potential future development; (5) the criteria for rope replacement; (6) potential future developments that could take place in both hoisting and rope inspection practices in Canada; and (7) recommendations.Subsequently, the report was issued by OMOL, and as a CD-ROM by CANMETMMSL. In this paper the author presents the key findings and the recommendations made in the study."

Jan 1, 2004

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981

By S. Kahraman, K. Develi, E. Yasar

Four hydraulic top hammers, one pneumatic top hammer, and three down-the-hole drills were observed in several rock types at quarries and highway construction sites to measure the performance data. At the same time, drill cuttings from each drill hole were collected for the determination of the coarseness index (CI), which is the sum of cumulative weight percentages of a particular size-graded sample of debris, and for the determination of median particle size (MPS), which is defined as the particle for which the quantity of particles equals 50% of the total of the cumulative distribution. After the sieve analysis was carried out on the drill cuttings in the laboratory, CI values were calculated and MPS values were obtained from the plots of cumulative undersize vs particle size. The performance data of the drills, CI values, and MPS values were analyzed using the least square regression method. It was seen that strong linear relationships usually exist between penetration rates and CI values, and penetration rates and MPS values for both top hammer drills and down-the-hole drills. Penetration rates increase linearly when increasing the CI and MPS values.

Jan 1, 2004

By P. K. Naik, B. Das

Flotation studies were carried out to recover carbon values from blast furnace flue dust containing ~30.34% carbon, 4.6% volatile matter (VM), and 65.03% ash. The variables chosen for the experiments were dispersant (sodium hexametaphosphate), pH, collector (diesel oil), and frother (MIBC). The experiments were designed according to a 24 full factorial design method and regression equations for the recovery of carbon and product grade were determined from the data. Experiments were performed to optimize recovery and grade using the steepest ascent method. The maximum recovery of carbon was 90.0% with a concentration of 56.5%, whereas the maximum obtainable grade of carbon was 66.35% with 50.45% recovery.

Jan 1, 2005

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By L. K. Daneshmend

"Competitive pressures dictate that the mining industry moves to larger mobile underground haulage equipment with more advanced equipment mechanization, higher levels of autonomous operation of machines, and longer periods between access by maintenance personnel. Since such new machines will of necessity be more complex than existing designs, machine reliability has become a key issue in progressing toward advanced mobile underground haulage equipment. Reliability and maintainability models of such equipment are practically non-existent in the literature. This paper addresses the issue of reliability and maintainability of mobile underground haulage equipment on two fronts: reliability modelling to enhance decision making for maintenance planning; and reliability simulation to enable evaluation of more rigorous production planning scenarios. A case study from a gold mine in the Chilean Andes is presented, for which reliability models of mobile underground haulage equipment, specifically load-hauldump vehicles and underground haul trucks, are developed, and a reliability-based simulation implemented. IntroductionMaintenance accounts for 20% to 35% of the overall operating budget for a typical underground operation, and hence represents the largest portion of the mine’s controllable operating costs (Cutifani et al., 1996; Campbell, 1997; Goddard, 1998). This, coupled with the fact that industry today is faced with an ever more complex and demanding marketplace, has led to an increasing interest in methods to reduce maintenance costs.Although significant effort has gone into developing effective maintenance strategies for industry in general, application of these to the"

Jan 1, 2003

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001