Search Documents

By J. D. Stinnette

Traditionally, airflow requirements for diesel equipment operating in underground environments such as mines and tunnels were determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations(s) or determined empirically from known quantities. In some cases, utilization factors were further used to adjust (reduce) the total airflow calculations for a diesel equipment fleet. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is currently a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. Tier IV engine standards mandate a reduction of DPM and NOx of approximately 95%, but can ventilation rates at mines with Tier IV equipment (or equivalent) really be reduced by a factor of twenty? This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and examines how they can be applied in determining a reasonable ventilation rate for Tier IV compliant equipment operating in subterranean environments.

Aug 1, 2013

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By John (Jack) D. Young, Frank M. Wheeler

Metallurgical plants are typically large, complex facilities. Their design is a multidisciplinary activity with a wide range of inputs, based on: the business case; metallurgical and process requirements; and the main processing equipment selection. Many constraints limit what can be achieved. Appropriate phasing of the design and development, and clear go/no-go decision criteria, are critical to successful implementation of a plant design project. Risk management concepts are used as a framework for successful project development, working from the business case, through project development, to implementation and startup, paying constant attention to technology, safe design, and sustainability. 1.1 INTRODUCTION The subject of “Metallurgical Plant Design” is the design of metallurgical plant facilities in the broadest sense. Plant design represents the culmination of many multidisciplinary activities: knowledge of process metallurgy is applied to design facilities to manufacture useful, economical, metal-based products. In the field of metallurgy, plant design is often overlooked, and its unique requirements are commonly not well understood, let alone appreciated. This book is a contribution to remedying this situation. The focus is the specifics of the metals industries, because an extensive literature already exists on the general topic of plant design.

Jan 1, 2015

By B. S. W. Buffam

"The property of Aunor Gold Mines, Limited, is in Deloro township, Ontario, about 3 miles southeast of Timmins. It consists of a group of eleven claims between the Buffalo Ankerite and Delnite mines.In the autumn of 1909, two brothers, John A. and W. S. Mitchell, joined the 'gold rush' to Porcupine. By the time they arrived the township of Tisdale, in which the Hollinger and Dome discoveries had been made, was staked solid but they managed to locate four claims in the northern part of Deloro township. Sufficient surface work was performed to bring the claims to patent in 1915. Following the Porcupine fire the Mitchells left the north to follow the oil developments in southwestern United States. In 1935 because of the rise in the price of gold and the successful development of the l3uffalo Ankerite and Delnite mines, they returned to Timmins and organized Augite Porcupine Mines, Limited, which combined the original four claims in Deloro and two adjoining claims controlled by Montreal River International Silver Mines, Limited. There were few rock exposures on the property, and as the overburden was generally deep surface exploration was impracticable. A programme of diamond drilling was, there; fore, undertaken in an endeavour to locate the western extension of the orebearing formation of the Buffalo Ankerite mine. This drilling was started in August 1936, and 5 months later ore was intersected at a depth of 500 feet on the south boundary of the property."

Jan 1, 1954

By Shanjun Mao

This paper summarizes current achievements of Digital Mining in China, puts forward the concept, framework and key technology of Smarter Mining, and finally points out that there is still a long way to go in order to acheive Smarter mining.

Aug 1, 2013

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By T. Robson

"A multi-seam underground mining operation employing mechanized room-and-pillar methods provides 35 per cent of Smoky River's annual ROM coal production (2 million tonnes) from the Smoky River coal field. Surface mines provide the balance. Tectonic activity, which has resulted in deformed coal seams and a rugged relief to the area, has provided natural boundaries to discrete mining areas. Coal transportation to the central preparation plant incorporates a 3 km long underground conveying system. The company is committed to efficient resource recovery and a safe and healthy working environment. Introduction The Smoky River Coal operations (SRC) are centered in the Smoky River coal field located in west central Alberta, some 360 km west of Edmonton and 20 km from the Town of Grande Cache (Fig. 1). Combined mining operations produce 2 million tonnes per year run-of-mine coal from which 1.65 million tonnes of high quality, low volatile, coking coal are obtained. The underground mining operation, employing mechanized room-and-pillar methods, provides 35 per cent of SRC's annual ROM coal production (2 million tonnes). Surface mines provide the balance. Tectonic activity has resulted in deformed coal seams and a rugged relief in the area. This has provided natural boundaries to discrete mining areas. Background Exploration of the Smoky River coal field took place over four decades commencing in 1926. McIntyre Mines Limited (parent to Smoky River Coal Ltd.}, commenced development of the property in 1968 having secured a long-term contract for the delivery of coal to Japan. Production of underground coal at Smoky River commenced toward the end of 1969 and has been continuous on the property since that time. Originally, two underground mines were opened. Original planning envisaged the use of room-and-pillar techniques to develop blocks of coal for subsequent extraction by longwall retreat mining. Following initial development, two longwall units were established, the first in November 1970 in No. 5 Mine and the second in February 1971 in No. 2 Mine. Difficulties were experienced on both units, and production commitments could not be achieved. The longwalls were discontinued, and mechanized room-and-pillar was subsequently used for all underground mining."

Jan 1, 1985

By Tim Grain Joseph

This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sand material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 square yards. Consequences are manifest in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability. The objective of these considerations, as part of the Oil sands Equipment Interaction Program (OsEIP); currently a joint venture between Syncrude Canada Ltd., JPi Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta; is to identify and provide feedback to the manufacturer and end user adverse shovel - ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance.

May 1, 2002

By John G. Henning

Low quality rock is encountered in many manifestations in underground hard rock mines, ranging from weak and poorly consolidated rock to highly altered or foliated rock. Lateral mine developments driven in low quality rock pose on-going challenges to a mine operator, as ground stability issues, such as caving of under-supported ground, drift closure due to surface deformation or buckling processes, and degradation of exposed rock surfaces are a persistent concern. For many operators, ground support design is an iterative process, as support practices are refined with time. Using case studies from a variety of underground hard rock mines, this paper reviews techniques for the classification of low range rockmasses and examines the rationale and effectiveness of adopted ground support systems.

Oct 1, 2010

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

Grinding with an electrochemically inert grinding media (i.e. high chrome white iron, or Magotteaux’s Duromax® alloys) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that is able to not only demonstrates these effects but also provide an indication of the magnitude of the improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at a number of operations around the world, including: Newcrest’s Cadia Operation, Oz Minerals’ Prominent Hill Mine and Glencore’s Ernest Henry Mine. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper, gold and molybdenum recoveries. INTRODUCTION The key to a successful separation in mineral processing is the preparation of particles with adequate liberation under the correct pulp chemical conditions. While the importance of liberation on flotation separations is generally understood and well documented in the literature (Johnson, 1987; Jackson, Sutherland, Gottlieb & Quittner, 1989; Young, Pease, Johnson, & Munro, 1997; Greet and Freeman, 2000), the importance of pulp chemistry is more nebulous, particularly with regard to the impact of grinding media. Extensive work examining the electrochemical interactions between grinding media and sulphide minerals has been completed (for example, Iwasaki, Reid, Lex & Smith, 1983; Natarajan and Iwasaki, 1984; Yelloji Rao and Natarajan, 1989(a); Yelloji Rao and Natarajan, 1989(b)). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution, therefore a galvanic couple between the media and the sulphide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).

Jan 1, 2019

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

By David Christensen

The long-term performance of dry covers is being examined in a research study funded by the International Network for Acid Prevention (INAP). The study was separated into two phases. The two main components of Phase 1 of the study were the identification and research of the processes affecting the long-term performance of dry cover systems and an examination of available numerical models for simulation of long-term cover performance. Identification and research of the physical, chemical, and biological processes affecting long-term performance showed that cover performance could be related to the change in the saturated hydraulic conductivity of cover material, the change in the soil-water characteristic curve, and the physical integrity of the cover system. Seven numerical models were examined to evaluate their effectiveness in predicting the long-term performance of cover systems. VADOSE/W (Online Help v1.01, 2002) was selected for use in cover system modeling in Phase 2 of the project. Phase 2 of the research study is currently in progress and involved the selection of five mine sites with a minimum of three years of performance monitoring data for analysis of cover performance. Two of the mine sites will be analyzed with the two-dimensional VADOSE/W numerical model. In addition, field saturated hydraulic conductivity tests were completed at three mine sites to investigate the change in field hydraulic conductivity of the cover system materials. The objective of the field testing program was to evaluate changes in hydraulic conductivity of cover material with time. Measurements of field hydraulic conductivity were completed with a Guelph permeameter and a pressure infiltrometer at three sites. The field hydraulic conductivity data was used to evaluate whether a change in this key material property had occurred over time. Field observations and the historic performance monitoring data provided the necessary information to develop hypotheses as to the likely processes that led to any change in field hydraulic conductivity. This paper will briefly summarize the research completed in Phase 1. The remainder of the paper will focus on the field testing program completed to measure the field hydraulic conductivity of constructed cover systems.

Nov 1, 2002

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939