Search Documents

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By A. Poor Zaeif Doost

With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.

Jan 1, 2012

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By G. Simard, D. Boudeville, A. Leclerc, A. Boivin

"The objective of this work is to study the various parameters that affect the overflow clarity of gravity settlers used in the precipitation circuit of alumina hydrate from the Bayer process. A mathematical model incorporating the size distribution of the feed suspension (Multi Size Group model), its diphasic nature (Schiller Naumann model) and the presence of turbulence (Shear Stress Transport model) has been solved numerically using ANSYS-CFX software. Preliminary results indicate that the overflow clarity is mainly controlled by lateral diffusion of fine particles (~20µm) from the exit of the feed well and by their upward transport from the sediment bed interface. Also the turbulence pattern in the settling zone seems to play a significant role in this vertical transportation. The validity of the model has been verified by comparing the measured solid concentrations from a pilot classifier with the calculated ones. This model could provide mineral processing plant operators and designers with a tool to optimize the configuration of classifiers with respect to the overflow clarity.INTRODUCTIONProblemIn the Bayer process, alumina hydrate precipitation from the saturated liquor is initiated in settler by adding crystallization seeds. Most of the precipitated alumina settles to the bottom of the tank while the liquor and the remaining alumina rise to the top, where they are removed at the overflow. Ideally the overflow clarity, which depends on the operational mode of the classifier, should be controlled within targeted limits."

Jan 1, 2016

By K. E. Waters, N. Brodusch, R. Gauvin, C. Teng, H. Demers

Rare earth elements play an increasingly important role in renewable energy devices and high-end electronics. In this project, the composition and morphology of REEs-bearing minerals are characterized with a field-emission scanning electron microscope at high spatial resolution and high counts rate using an X-ray silicon drift detector system. High spatial resolution imaging and energy dispersive X-ray microanalysis were applied at low and high magnification to obtain the composition of each phase in the minerals. From the standardless quantitative analysis results, the amount of REEs in each phase was measured and the relationships between those phases were identified.

Jan 1, 2014

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By W. C. Ferguson

"This paper could be more appropriately titled ""The Application of Vacuum Filters to Underground Minewater Treatment. in a previous paper co-authored by the writer (1) the history and development of minewater treatment at the Sudbury District Operations of the International Nickel Company was outlined. It is the intention of this paper to dwell more specifically WIth the the application of the vacuum filter to a problem found in most, if not all, underground mining operations. In the preparation of this paper the writer has made liberal use of the illustrations and text of the paper previously noted.Last year we heard Mr. Nemeth discuss the basic mechanisms involved in vacuum filtration (2), and today Yr. Cunliff has exposed us to the selection of the filter media (3). I will now briefly review the various vacuum filter designs that generally lend themselves to metallurgical dewatering applications.DRUM FILTERSThe revolving drum-type which filters on its outside periphery is illustrated in Fig. 1. This is the Oliver or Drum filter and represents the first commercially available continuous vacuum filter. The original design dates back more than 50 years, but with the exception of the method of discharge, is identical to the units being marketed today. This filter is generally applied to slow filtering slurries. The cake may be discharged in several ways; strings, scraper blades, rolls or by passing the filter cloth over a small diameter discharge roller (belt discharge).THE DORRCO FILTERThe revolving drum type which filters on its inside periphery is illustrated in Fig. 2. Here the slurry lies in the drum and the cake discharges through a chute or conveyor. This type of filter is most often applied to fast-filtering slurries.THE DISC FILTERThe revolving filter which filters on the vertical plane of the disc is referred to as the Disc or American-type filter. This represents the most inexpensive design in terms of cost per square foot of filter area. This filter is widely applied, but is probably more suitable for slower draining pulps."

Jan 1, 1971

"There are a number of disciplines in the minerals industry for which concern has been expressed regarding the sustainability of human capital. The boom-bust cycles that occur in the industry, the trend in tertiary education towards consolidation or in some cases cessation of minerals related programs and the increasing frequency of fly-in fly-out operations can all contribute towards a decline in the number of professionals with basic skills in process mineralogy. This paper describes approaches taken by the authors to incorporate process mineralogy into three levels of education, namely undergraduate, recent graduate and experienced professionals. The primary objective in designing the learning activities is the development of authentic learning experiences that provide participants with relevant skills in process mineralogy. Selected examples of approaches used by other education groups globally to address this issue are also provided.INTRODUCTIONThe boom and bust cycle of the mining industry has trickle down effects in tertiary education in terms of the ability of universities to consistently provide high quality graduates with relevant skills. When the commodity price surged in 2002 skills shortages in critical resource related professions were reported and despite investment in skill development there was a view from employers that not enough young people were graduating from relevant education programs (PricewaterhouseCoopers, 2012). At the time this signalled positive growth for engineering disciplines catering to the mining industry, however during the downturn cycles, most recently since 2012, graduates exiting from the discipline can find employment difficult and this contributes to reduced enrolments in subsequent years. From an AusIMM (Australasian Institute of Mining and Metallurgy) members’ employment survey conducted in 2013, more than half of the graduates exiting from disciplines related to mining and minerals were not confident of finding employment (AusIMM, 2013). In the long term the concern is not only how to sustain enrolment and graduate numbers but also to provide the opportunity for students to acquire the professional skills that they require to make them attractive to industry.Maintaining and sustaining core competencies in the minerals discipline is an ongoing challenge. There have been a number of recent papers on this issue presented at international conferences (e.g. McCaffrey et al, 2014; Drinkwater and Napier-Munn, 2014) and there is general agreement that one of the ways in which the deficit in foundation concepts can be addressed is through workplace development. Drinkwater and Napier-Munn (2014) presented data from a survey of industry professionals that indicated that more than 90% of respondents undertook on average 30 days of training each year of which approximately 5 days was professional short courses."

Jan 1, 2016

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By Judith S. Chan

With the increasing awareness of the need for the reduction of carbon emissions globally, geothermal energy, which offers a potential for cleaner energy generation, is one potential new source. In Alberta, these geothermal resources are likely to be found in the sedimentary basin, or in the deeper crystalline basement rocks. Alberta exhibits a very low geothermal gradient compared to other existing geothermal fields located in areas of volcanic and tectonic activity. To mitigate this effect, the focus in Alberta will involve the development of engineered geothermal systems (EGS) in the target resource. The first goal for EGS research and development is to develop a detailed geological-geophysical characterization of selected sites to delineate potential geothermal reservoirs in Northern Alberta. One of the selected sites is in the Fort McMurray area. The deepest well drilled in the oilsands areas of Northern Alberta is located just west of Fort McMurray. It has a depth of 2363 m and as such can provide details on the physical properties of the rocks, the state of stress, and the existence of fracture porosity toward geothermal investigations. To date, we have acquired temperature logs to study the change in geothermal gradient with depth, and a series of petrophysical logs to study the finer scale structure of the rock formations with vertical resolutions in the range of 0.05 cm to 80 cm. Our aim is to identify geological features such as zones of fractures in the basin and/or basement that could provide an indication of enhanced fluid flow potential ? a necessary component for any geothermal systems to be viable. Zero offset and walkaway vertical seismic profiles (VSP) were also conducted to measure the seismic responses at the borehole. VSP data can be used to delineate the structural and stratigraphic features surrounding the borehole that could not be resolved from surface seismic reflection data that are also available near the borehole. The full integration of well logs, VSP data and surface seismic reflection data are expected to provide a detailed characterization of the sedimentary basin and crystalline basement rocks of the Canadian Shield in Northeastern Alberta and will assist in future planning for drilling.

Jun 1, 2012

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By A Smirnov

The problem of thin and very thin coal seam extraction is examined in a long perspective of Ukraine?s fuel and energy industry development. The technical and economic benefits of the coal seam selective mining technique are described, including beneficial environmental impact.

Aug 1, 2013

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978