Search Documents

By E. Sigal

Overview ?Intrinsik has completed several wide area HHRA and ERA studies of mining and smelting communities ?Several ?Lessons Learned? ?Key areas related to: ?Study Design ?Data Quality ?Bioaccessibility ?Speciation ?Weight-of-Evidence Approaches ?Advances in Ecological Risk Assessment Techniques

May 1, 2009

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By R. C. Urquhart

Since the first use of the electric arc furnace Henri Moissan (1892) and its use by Paul Hérholdt (1902) to melt steel, it has been successfully used as a pyrometallurgical smelting tool in the production of calcium carbide, iron, ferrous and non-ferrous alloys. Commercial forms of the electric arc furnace have evolved from round, single-phase single electrode units to rectangular three electrode three-phase units to round three electrode three phase units and ultimately to rectangular six electrode three-phase units. DC electrical supply has also been used to replace the three phase power supplies in some cases. This paper examines how these electric arc smelting furnaces have evolved in size, efficiency and configuration within the constraints of the smelting process, electrodes and electrical power supply equipment.

Jan 1, 2014

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011

Oct 1, 2010

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006

By A. J. W. Law

"This paper deals with the organization of the central office technical areas and the role played during the feasibility studies, construction and operating phases of Les Mines Selbaie.HistoryThe Engineering Department was originally formed as a part of the Exploration Department, to examine the feasibility of advanced exploration prospects being brought to the company. In 1968, with the discovery of the South Bay property in northwestern Ontario, the department became part of a Mining Division and was expanded, so that it could provide more advanced mine feasibility studies, control of construction engineering and procurement and initial mine design. As is generally the case, the mine design function was handled with in-house capability, while plant, mill and const ruction functions used outside consultants.The 1974 discovery of the Selbaie deposits, started a period o f growth in the capabilities o f the department. The complex nature of these deposits, required that skills were added in the mining, metallurgical and plant areas. During the early feasibility study period these skills were provided by the engineering company of the parent group, but when it was realized that production from the deposits was likely, permanent staff was added."

Jan 1, 1990

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By Raynald Vézina, Richard Leclerc, Jean Boissonnault, Louis P. Gignac, Gérald Veillette

Since mid-1989, Cambior has increased its producing gold mines from four to six, having acquired the Chima Mine and brought the Silidor Mine onstream. In June 1990, the company announced that the Mouska project would also be put into production. Gold production reached almost 190 000 ounces in 1989 and is expected to exceed 220 000 ounces this year. Cambior has also a non-gold operation with an interest of 50% in the Niobec Mine and has recently signed an option agreement in the development of the Lac Knife graphite deposit in northeastern Quebec. During the past year, the company has extended its exploration activities to the United States and Indonesia, and now has interests in nearly 80 properties. Last May, Cambior signed an option agreement with Golden Star for a gold deposit in Guyana, the OMAI Project, containing at least 2 000 000 ounces of gold in situ.

Jan 1, 1990

By C. A. Biley

"A dedicated iron removal stage was installed at Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) during an expansion project which began execution in 2010. The Pressure Iron Removal (PIR) process aims to precipitate iron from a nickel leach solution under medium temperature (145 °C) oxidative conditions using caustic for neutralisation. Since commissioning, the process has been robust in removing iron from the refinery but has shown significant variability in the residues produced. These residues, which are typically comprised of ferrihydrite, hematite or natrojarosite, have varying iron contents and different physical properties which have implications for their filtration and ultimate removal from the refinery. Since over 95% of nickel plated at RBMR passes through the PIR section, volumetric constraints caused by poor filtration performance directly influence nickel production and stabilisation of this process remains central to the continued ramp-up of the refinery to full nameplate capacity. This paper details the development of the PIR process and the journey from concept to implementation. Recent laboratory and plant scale tests have highlighted the importance of the initial phase formed in the autoclave for the ultimate residue requiring filtration and how the feed acid concentration is a critical control parameter. On this basis, a new caustic dosing philosophy was implemented which improved pH control in the autoclave. Further optimisation of the PIR process is on-going.INTRODUCTIONIn 2010, an expansion of Rustenburg Base Metal Refiners (RBMR) to increase nickel production from 21 to 33 ktpa began execution. The management of iron was pivotal in the ultimate configuration in the new circuit and one of the primary differences from the original circuit was the addition of a dedicated iron removal stage: Pressure Iron Removal (PIR). A significant drive for this new unit operation was to facilitate the separation of iron from other leach residues. Not only did this result in a significant decrease in the amount of leach residue but, without the constraints associated with iron precipitation during leaching, has permitted more aggressive leaching conditions and, correspondingly, greater throughput and efficiencies.However, as with many commercial implementations of even mature technologies, the journey from development to implementation has presented challenges for the continued ramp-up of the refinery to full nameplate capacity. Specifically, since all nickel bearing leach solution must pass through the PIR section prior to the nickel purification and recovery circuit, throughput difficulties in the PIR section can directly impact supply of feed to the nickel tank house. Since commissioning, the PIR autoclave has effectively removed iron from the refinery, but has shown significant variation in the solids phases produced in the autoclave. This variation presents difficulties for the filtration of the discharge slurry and represents a key throughput limitation which periodically impacts production. Additionally, the increasing production rates associated with the ramp-up of the refinery have resulted in a significant increase in the required volumetric throughput through the PIR process. This has placed even greater emphasis on improving the stability of the solid phase produced in the autoclave, ultimately targeting an easily filterable residue with high iron content."

Jan 1, 2016

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By N. Plint, M. Potgieter

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By Palaniappan Chidambaram

Despite the advances in processing technologies, construction techniques, inspection methods, and materials, the number of process safety incidents are still increasing, and often the same types of incidents are being repeated. While regulators are enforcing stringent requirements in regards to safety management systems, process safety incident statistics reflect a failure in effective implementation. Upon closer look at the implementation of safety management systems, it becomes evident that the systems were not built on robust risk recognition. The risk-based implementation approach enables facilities to develop systems focused on managing specific risks and quickly gain momentum and confidence to take next steps towards implementing comprehensive systems. This paper will cover the importance of risk recognition and governance, risk based implementation and the role of Process Hazard Analysis in managing operational risks through the lifecycle.

Jan 1, 2014

By J. P. McGeer

"With the ever-increasing flood of new science and technology has come a new approach to design. The combination of these factors has produced an ever-accelerating pace of materials substitutions.Examples to illustrate the points made above will be given. An overview of the current new materials fields will follow. Finally, the particular nature of the challenge for Canada will be discussed. IntroductionThere are a number of forces currently at work which make it mandatory that the Canadian resource sector re-examine its strategies and policies. The author thinks there need to be very significant changes in the business plans of Canadian mineral processing corporations. Current changes in our environment demand such a reaction.The changes in our environment include more rap id substitution of materials; a significant alteration in design philosophy; the global economy; and market saturation and market diversification in dev eloped countries.This paper will cover the changes and illustrate how they will affect the Canadian resource industry. It will show some of the ways that Canadian corporations are reacting to maintain profitability. Finally, some policy issues will be considered"

Jan 1, 1988

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014