Search Documents

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"The Western Research Centre (WRC) of CANMET operate a unique pilot plant facility where ongoing R&D on coal preparation and mineral processing is conducted. The pilot plant carries out two functions: coal preparation processing using state-of-the art technology and coal-liquid mixture preparation with intensive cleaning circuits that can also be used for mineral processing. In total, the pilot plant includes more than 30 different flowsheet options. The facility is dedicated to small and fine coal, and designed to be flexible and versatile.This paper describes the use of a pilot-scale facility as a research tool for process control development, fine coal beneficiation, development of coal-liquid fuels technologies, development of process models and testing and evaluation of new developments. The pilot plant is used to assist in resource development by evaluating and optimizing flowsheet selection, and producing sufficient samples for utilization tests. The facility is also an important tool for evaluating and testing samples from troublesome circuits of operating plants to find means to optimize and improve recovery, particularly of fines circuits.Detailed examples are given to demonstrate the role of a pilot scale facility in coal preparation R&D, coal industry development and optimization of coal processing operations. These examples include the development of heavy-medium cyclone computer control system, detailed evaluation of beneficiation of a coal deposit with high clay content, development of column flotation, and its role in fine cleaning circuits and treatment of ultra-fines in relation to intensive cleaning, the importance of testing coals in different processes, and cleaning processes influence on coking quality and other utilization applications. The potential of the facility for helping the mineral industry is also described."

Jan 1, 1992

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By R. del Villar, A. R. Laplante

"This article presents four grinding simulation programs, written in Applesoft BASIC. The firs t two calculate residence time distributions (RT Ds) for open and closed loops mills. The third program calculates the select ion functions from the RTD, breakage function and particle size distribution (PSD) o f the feed and discharge. Two linear regression programs are also included to calculate the breakage function. These results are used in the fourth program to simulate continuous or batch grinding kinetics.The modelling approach presented is the size discrete, time continuous matrix formulation presented by Reid (1965) from concepts originally proposed by Epstein (1948). It is at the present time the most widely accepted phenomenological model of grinding kinetics and is standard textbook material (Austin et 01., 1982; Kelly and Spottiswood, 1982, p. 152). The concepts of RTDs and tracer testing originated from chemical engineering theory and practice, and are well presented in Leven spiel (2n d Ed . 1972 , Ch. 9) .Applesoft* was chosen because it is compatible with many micro computers. It is also one of the simplest and least powerful BASIC versions. Thus it can easily be adapted to other more complex BASIC versions.Open Loop Residence Time Distributions (Program RTDOPEN)As mixing, channelling, stagnation and short-circuiting all affect slurry motion in tumbling mills, transport characteristics are very complex an d cannot be derived from fundamental principles. Fortunately , as grinding follows first order kinetics, transport characteristics for the purpose of grinding simulation ca n be represented by the RTD of the slurry phase . It is normally determined using liquid tracers, as it has been demonstrated and is commonly accepted that in industrial ball mill s, the RTD of the so lid phase is particle size independent and equal to that of the liquid phase."

Jan 1, 1985

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By Miguel A. Cuba

Resource models are generally constructed using data of different types and/or from different sources. A common issue is the consistency of scale in the information that often leads to a requirement to composite the data prior to model construction. For the purposes of mine planning, development and/or resource assessment, this model may then be upscaled to a relevant selective mining unit. It is well established that the geostatistical parameters for resource model construction is scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the variogram that should be used in model construction and/or the assessment of volume variance relations as it affects resource estimation. The scaling laws are a set of guidelines that detail how the variogram should change as a result of a change in the volume; these laws are empirically derived and involve some simplifying assumptions, not the least of which is an assumption of shape invariance in the variogram structure. An alternative approach was proposed to directly upscale the variogram via numerical integration, which demonstrates that the assumption of shape invariance is not required and we can directly access the new variogram shape given any volume of interest. This paper compares these two different approaches to variogram upscaling by considering two applications: the first corresponds to a 2D synthetic case and the second looks at a 3D case with data from a porphyry copper deposit. The simulation studies in these cases show that the direct upscaling approach performs better than the scaling laws in fitting the average experimental variogram values at any block size. This is based on a mean absolute error criterion. Moreover, it is also shown that with an increase in the block size, direct variogram upscaling significantly outperforms the scaling laws approach.

Oct 1, 2009

By G. R. Cope, C. D. Spence

"The Mac porphyry molybdenum prospect is located 100 km east of Smithers in central British Columbia. The identification of anomalous levels of molybdenum, copper, and silver in three adjacent lakes, sampled during a regional lake sediment survey, lead to the discovery of molybdenite mineralization in float. Subsequent magnetic and soil geochemistry surveys, together with prospecting and mapping, located the source of the float. Mineralization is hosted by a leucocratic granite stock of the Upper Jurassic to Lower Cretaceous Francois Lake Intrusions which has intruded Carboniferous and Permian Cache Creek Group volcanic and sedimentary rocks. The stock measures 500 m by 300m at surface and is mineralized throughout. Sulphide mineralogy is simple and consists of molybdenite with minor pyrite and local chalcopyrite. Molybdenite occurs within fractures and as selvages along quartz stockwork veins and is best developed near the margins of the stock.Known mineralization is coincident with distinct soil geochemistry and magnetic anomalies. Two additional areas of the property display similar features and these remain to be tested.IntroductionThe Mac property is situated in the Babine Lake area of central British Columbia on NTS map sheet 93K/13E, approximately 100 km east of the town of Smithers (Fig. 1). The property lies on the western margin of the Hogem Range at the northern tip of the Nechako Plateau. The centre of the claim block lies at 54°51 ' 30""N and 125 °34 '30""W.Topographically, the claims are characterized by gently rolling hills ranging in elevation from 900 m to 1500 m. Slopes are forested with tall conifers and underbrush is minimal. Flat-lying areas are swampy with tall grasses and scrub brush.Presently, the property is only accessible by helicopter from bases located in Smithers and Fort St. James. Recent road construction by the British Columbia Forest Service has brought road access from Burns Lake to within 5 km due south of the property. It is expected that in the near future, roads will be advanced into the claim area to facilitate logging of mature timber."

Jan 1, 1995

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By C. Fortin

The subject of gold flotation has been reviewed extensively in a number of publications. The focus in most of these reviews has been on the theories of gold flotation as well as the physical and chemical effects that may impact the efficacy of the gold flotation process. It is evident that the current status of gold flotation chemistry as it is being applied in industry has not been addressed widely. It is the intent of this paper to review current gold flotation practice and how these applications tie in with the current understanding of the chemistry of gold flotation.

Jan 1, 2011

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970