Search Documents

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By M. Beth McClenaghan

This paper summarizes diamond exploration techniques used in glaciated terrain, focusing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments are essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 to 0.5 mm) fraction of heavy mineral concentrates prepared from glacial sediment samples is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and REE, the relative importance of which will depend on kimberlite composition as well as that of the surrounding bedrock.

May 1, 2002

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

By R. Siy, O. Neiman, B. Hilscher

"A full-scale prototype of “Jameson Downcomer” technology has been installed and tested on a Tailings Oil Recovery (TOR) vessel in Syncrude’s Mildred Lake extraction plant. Jameson Downcomers are a type of mineral flotation equipment used in the coal industry that Syncrude has extended to the recovery of secondary bitumen in the oil sand extraction process. The TOR vessels are currently being operated as single-gravity separation vessels, in series with the Primary Separation Vessels (PSV’s). We have developed a model to differentiate between “floating” and “non-floating” bitumen in the PSV’s, and then applied it to verify that the current TOR performance only captures the “floating” bitumen by simple separation. The existence of “non-floating” bitumen provides an opportunity for recovery enhancement by means of the Jameson Downcomers. To achieve bitumen recovery enhancement, middlings slurry is withdrawn from the TOR vessel, and passed through a number of parallel Jameson downcomers, within which the slurry is accelerated to a high-velocity free jet, and impinged upon the slurry surface inside the downcomer, in the presence of air. The aerated slurry is returned to the middlings zone inside the TOR, resulting in an incremental recovery improvement of bitumen in the TOR. The operation of the downcomers is thought to produce suitably small air bubbles for the flotation of bitumen, either by fluid shearing during the slurry jet impingement, and/or by micro-bubble nucleation. This full-scale prototype design has met or exceeded the recovery expectations of the original Research piloting, recovering at least 40% of the non-floating bitumen. In Syncrude Extraction, this provides high business value by a separation efficiency gain achieved with modest expenditure. As well, the system has demonstrated excellent operability and maintainability.INTRODUCTION Syncrude Overview Syncrude Canada Ltd. is one of the largest producers of crude oil from oil sands. Our crude oil production facility has the capacity to produce over 15% of Canada's total oil requirements. To do this, we surface mine oil sand, extract the raw oil known as bitumen from the sand using water-based processes, and upgrade that bitumen into sweet light crude oil by fluid coking, hydro processing, hydro treating and reblending. Our final product, Syncrude Crude Oil (SCO), is sent by pipeline to three Edmonton area refineries and to pipeline terminals which ship it to other refineries in Canada and the United States. The Syncrude operation is comprised of four major technology areas: Mining, Extraction, Upgrading and Utilities. As well, Syncrude invests more than $40 million annually in science and technology, and is among the top 50 companies in Canada for Research and Development (R&D) investment. Syncrude holds 21 active Canadian and U.S. patents."

Jan 1, 2012

By Bruno Lemelin

Falconbridge Ltd Raglan Mine has been in production since 1998 and has produced annually some 900 000T of ore grading 3.1% nickel, 0.9% copper and 0.06% cobalt. The mine is located in Nunavik, Northern Quebec. The current mine life is estimated at approximately 20 years. Reserves are composed of numerous small ore bodies situated across a 65 km strike length. Planning the extraction of the ten small mineralized zones represents a great challenge to optimize. The overall objective is to maximize the company?s return on net assets. Actual planning uses computerized technology tools like Automod and Mine2-4D, and a conventional discounted cash flow method (DCF) of calculating net present value (NPV). The complex setting of Raglan could benefit from advance valuation techniques such as the real options method (RO). This paper will present the characteristics if the mines that make it a good candidate to use RO to gain further insight.

May 1, 2004

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By R. E. McElvain

"Hydraulic transportation of solids in suspension with water or other carriers, such as oil is becoming more practical as economic situations develop with respect to the railroads and other carriers. Of significant importance, is also the increased size of the major operations and the total impact of larg- er tonnages and more critical sources of supply.There are several means of imparting energy into the solids and directing the material down a pipeline, but the centrifugal pump is emerging as the most practical piece of equipment when considering relatively large flows and recent development. We can now handle relatively high densities without interruptions. This provides the mining and transportation fields a more economical means of lifting and transporting coal and other mineral products.Equipment & MethodsWarman International has developed several methods of alternate PDP against high heads. We have, at least for the present time, shelved our pump which uses clear water to slurry method and have placed our major emphasis on the full development of the centrifugal pump. I personally see several similarities on the alternate reciprocating devices as compared with the steam piston type engine versus steam turbines. The centrifugal pump comes into its most advantageous position at about 2000 GPM and can also show advantages by means of increased mobility, when driving tunnels and in other difficult operations when considering the total economic results. We now have some interesting d<:ta on one 5 mile raw silica sand line designed for pumping at 200-400 tons per h:mr. This is a separate subject on a ""simplified approach to slurry transport"" and paper has been prepared for the Hydrotransport 5 proceedings in Germany this Spring. Reference 1 may be of interest to those who want to delve into the subject further, and I also have some advance copies of this paper."

Jan 1, 1978