Search Documents

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By L. H. Chen, Y. C. Chen, Leo Benyamin, W. C. Chen

"To investigate the evolution of fluid-driven fracture of rock-like material subjected to borehole fluid pressure and its consequential damage with regard to post-peak stabilization, micro-seismic activities have been monitored using nondestructive technique of acoustic emission (AE) corresponding to the macro-scale complete history of loading curve by setting the hollow cylindrical external circumferential strain to be a closed-loop feedback signal during servo-fluid-driven tests. Development of a novel fluidinduced loading system injected from internal borehole as well as monitoring system were equipped such that the initiation and propagation of micro-cracks enable to analyze experimentally. By programming/controlling either injection rate or fluid pressure, synthetic sandstones with low-permeability made by cement mortar were conducted in this study. It found that both the growth of macro-crack initialized intensively as reaching the breakdown pressure and the micro-seismic activities represented by AE locations show nice agreement. The experimental results in this paper provide better understandings of fluid-driven fracture mechanism.INTRODUCTIONFluid-driven fracture is a process of generating cracks by injecting viscous fluid into solid material. Conventionally, fluid-driven fracture tests have been performed by mining industry to measure the in situ stress (Haimson & Fairhurst, 1969) and fluid-driven fracture has been employed by the petroleum industry to recover oil and gas. Additionally, the mechanism of crack growth or the extension of existing cracks is important to the evolution of volcanic dikes over distances of a few kilometers (Lister & Kerr, 1991; Rubin, 1995), crack propagation in dams (Bolzon & Cocchetti, 2003) and the disposal of radioactive waste (Sun, 1969)."

Jan 1, 2015

By G. Forté, R. Girard

The Alcan Bayer Process Experimental Centre (BEC) is an essential development tool for the Bauxite & Alumina researchers at the Alcan Arvida Research and Development Centre in Jonquiere, Quebec. Between the laboratory tests and the industrial prototypes or the industrial applications, the BEC is a key element for technology transfers. The Bayer process is the extraction of aluminium oxide (or alumina) from the bauxite ore. The Bayer Experimental Centre's history and flowsheet are presented. The major pieces of equipment are described. Safety and design considerations are presented. Finally, examples of applications, double digestion and pressure decantation, are briefly described.

Jan 1, 2004

By W. L. Single

"LET ME FIRST OF ALL thank you for sending this invitation to me to participate in this Annual Meeting of The Mining Society of Nova Scotia. As an engineer, although I don't get an opportunity to practice very much engineering these days, I am, of course, always pleased to be able to meet with my fellow engineers to exchange views, but I must admit that today I feel a little bit out of place in the midst of all the experts that are here today. Let me make one thing clear - I'm a generalist! Your program states that I am to make a keynote address. I have always thought that a keynote speech is one that says something that has not been said before - announces some new program or policy, or says something startling. I am sure you will understand when I tell you that keynote addresses are made by politicians and that civil servants speaking publicly are usually expected to give an account of what is, or what is likely, to happen as a result of policies that have been announced in keynote speeches by politicians. I am reminded of a statement by a distinguished parliamentarian who said, ""However exalted a civil servant may be, he is not above the elected officials."" So today I will confine myself to giving you an overview with particular emphasis on the development side of oil and gas. The theme of ""Oil and Gas"" is a topical one these days. I suppose it's because of all the copy that is being generated by the media on the U.S. energy crisis, the Mid-East situation, the fact that most of the world's proven oil reserves are in Arab hands and, of course, the accelerated exploration activity that is taking place in the North Sea, in the Arctic, and off the coast of Newfoundland and Nova Scotia."

Jan 1, 1973

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By P. Archer

The Blondeau Formation has been examined in a stratigraphic drill section at Barlow Lake. The formation contains pyroclastic flows and volcanogenic sediments throughout, but epiclastic sedimentary rocks dominate the upper parts of the section. Five distinct types of pyroclas tic flows are known in the section, as well as minor mafic lava flows. Volcanogenic sediments are commonly intercalated with the true volcanic rocks. Sedimentary rocks include fine-grained intraclastic sandstones, heterolithic sandstones and green and black shales. Interpretation of the origin and relative disposition of the volcanic and sedimentary rocks favours a model of near-emergent vulcanism in an upward shoaling environment.

Jan 1, 1984

By C. Gerow

THIS paper is entitled "Some" problems, rather than "The" problems, met in selling coal, since the problems to be met in selling any commodity have to deal with an infinite number of circumstances and conditions. These are believed to be more varied in the case of coal than probably any other commodity. This is due, perhaps, to the fact that coal has been one of the basic materials in the guiding of industrial and national achievement for the past two hundred years. During this time its use has developed from a most haphazard one to uses involving all modern scientific methods, which, rather than simplifying matters as regards the marketing of coal, have added many fresh problems, and these vary according to the particular market served. Since the concern of this paper is primarily the selling of Nova Scotia coal, it is proposed to deal chiefly with some of the specific conditions met in the markets presently served by this coal. For the purpose of discussion, these markets may be considered as divided into three main groups, namely, the Maritime market, the Quebec market, and the Ontario market. THE MARITIME MARKET First of all, let us consider the Maritime market. This is a market which has been regularly served by Nova Scotia coal since coal mining became the first industry in Cape Breton, slightly over one hundred years ago. Conditions as applying to the use of coal have naturally tended to adjust themselves to the characteristics of the coal most readily available, and, therefore, marketing problems are fewer in the Maritimes than in districts where many coals of varied characteristics are offered. Up to recent years, the problems involved were chiefly those of providing satisfactory service insofar as de-liveries were concerned. However, with the speeding-up of manufacturing processes and the necessity of reducing costs to a minimum, users of coal have become interested in obtaining coal that will give the most economical service. It is, therefore, now of importance that the salesman should have full knowledge of the particular conditions applicable to each customer's use in order to deal to the best advantage.

Jan 1, 1936

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

By D. O. DeGagné, J. F. Archibald

Spray-on polymer linings, as partial or full replacement for traditional forms of area rock support, have seen rapid growth in interest within Canada. A wide variety of lining types, ranging from polymer chemical to water-based cementitious materials, have been developed and commercially introduced to the underground mining market. Following approximately one decade of development work, several general conclusions have been reached regarding the performance of this class of area support media, these being that: health and safety assessment of the broad range of materials has shown the majority of them to be acceptable and safe for underground use; significant ground support potential can be offered by them, being equivalent to or better than capabilities offered by traditional support forms such as bolt-and-screen or shotcrete, and; their abilities to be rapidly deployed and provide near instantaneous support restraint offer considerable operational and cost benefits to underground operators. A review of currently available liner materials, their historic development within the Canadian mining industry, and overviews of support, health and safety, operational considerations and cost benefits are provided in this paper.

Jan 1, 2001

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV-500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV- 500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By J. W. Stickney

"On July 1, 1977 Hudson Bay Mining and Smelting Company Limited announced the commencement of construction of a 3800 ton per day concentrator at Snow Lake, Manitoba. Snow Lake, a community of 2200 people, is located 130 road miles from the main metallurgical plants at Flin Flon.The design, detailed engineering and equipment selection for the project was awarded to Wright Engineers Limited of Vancouver, B.C., who would be working in close liason with Hudson Bay Mining personnel throughout the project.The feasibility of constructing a metallurgical plant in the Snow Lake area, in addition to the concentrator at Flin Flon, had been under study since 1964 with plants of varying capacities and designs being considered. Each successive study recommended a plant of increased capacity and sophistication and finally upon an in-depth study in 1976 of ore reserves, freight rates and operational benefits, the construction of a 3800 ton per day copper-lead-zinc concentrator appeared highly benificial."

Jan 1, 1981