Search Documents

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By D. Verhulst

The Altair process digests ilmenite concentrate in high-chloride HC1 solution, with complete dissolution of titanium and iron. The Fe(III) ions are reduced to the ferrous form, and the solution is cooled to produce crystalline ferrous chloride. Titanium is transferred by solvent extraction into a purified, concentrated Ti stream, which is spray-hydrolyzed to produce TiO2 hydrate. The hydrate is further calcined with additives to generate a high-quality pigment. All the chloride streams are recycled. In the original flowsheet, the iron chloride is pyrohydrolyzed by spray roasting to regenerate 18% HCl, which is subsequently converted to HC1 gas and water by pressure-swing distillation. A modified flowsheet includes an alternative to iron chloride spray roasting, producing more concentrated HCl and decreasing the amount of solution to be distilled. Improvements in digestion, solvent extraction and final pigment production are also introduced. A 100 t/y pilot plant is being built and will test the new concepts and confirm the overall water, acid and impurity balances of the process.

Jan 1, 2006

By G. S. Headley

At the Sullivan Mine, recent experience with sulphide fires, locally referred to as " hot muck", has necessitated extensive modifications to pillar mining design and operating procedures. Potentially hot pillars are now being designed and mined to prevent fires. Unusual safety hazards and difficulties are encountered in working with, and adjacent. to, existing pillar fires. Operating procedures developed for these conditions have proved successful for safe and continuing production. These changes have minimized the impact of hot ore on current operations and have promise for an improved future.

Jan 1, 1977

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By A. Todd Davis

"Introduction“CAN YQUR Company afford not to train?"" This question was asked by Jack Taylor in the Factory Management Magazine for June, 1950. Mr. Taylor went on to say, ""No, it can't; no Company can"". It's true that many training programmes have not done the job they were designed to do because of a number of factors such as parts of management resenting training, management failing to understand the abstract values of training, and management giving impossible assignments or picking the wrong trainers. However, Mr. Taylor summarizes his article by saying that a properly-designed and •conducted training programme brings a company or a corporation to the point where the question is: ""Can my Company afford not to train?""About two years ago, in July, 1952, Nevada Mines Division of the Kennecott Copper Corporation embarked on a training programme, the same type of programme that had been inaugurated earlier at the •Utah Copper Division at Bingham, Magna, and Garfield, Utah. President Charles Cox of Kennecott, in •a speech made •before the Utah Bankers Association in June of 1951, stated that, ""I think that our programme of employee training is one of the most important phases of our entire operation"". That statement might be said to be one of the guiding principles of training at Nevada Mines Division. Training is supported by top managements and down the line to Division managements. As the years go by, the Company expects to receive many benefits from training."

Jan 1, 1954

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By John Wightman

LOCATION OF PROPERTY THE property of Caribou Gold Mines, Limited, is situated in the north-eastern part of Halifax county, seven miles south of the Canadian National railway line at Upper Musquodoboit. Approach to the village is by a secondary road, improved recently by waste rock from the mine dump. A two-wire telephone line, seven miles long, built and owned by the present operators, provides communication to the nearest telephone exchange, Parker&apos;s Corner. HISTORY In 1870, the Caribou area was recognized as a proclaimed gold district. From then on, operations were intermittent, with periods of considerable activity by small companies until there were no fewer than seven mines in a district two miles long by three-quarters of a mile wide. These were the Holman, Truro, Caffrey, MacDonald or Elk, Lake, Dixon, and Hilchey properties, all of which have had separate stamp-mills, and have produced gold for varying periods. Depths of the workings range from 100 feet to 1,000 feet. Power was generated at each property by means of steam boilers. At the present time, the Consolidated Mining and Smelting Company of Canada, Limited, controls all the leased areas, approximately 800 acres, and is operating by means of one central vertical shaft. GEOLOGY The district in and about Caribou Mines has an elevation of approximately five hundred feet above sea level. The area is fairly well wooded, with rock outcrops here and there. These outcrops, along with information from test-pits and shafts, have been the basis for the very excellent geological map of the district prepared by E. R. Faribault some years ago. The rock structure, which is one of the best examples in Nova Scotia of an elliptical dome, has its anticlinal axis in a northeast-southwest direction, and flat plunges in the same directions.

Jan 1, 1938

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By M. Sukhram

In the year 1992, T.A. Utigard published a paper titled "The measurement of the heat-transfer coefficient between high temperature liquids and solid surfaces." In that work, he instrumented an agglomerate of materials with thermocouples to infer the heat transfer coefficient of a high temperature liquid on a solid. The purpose of that research was to help in the design and operation of metallurgical reactors. Since that time there have been many researchers that have worked to characterize heat, mass, and momentum transfer phenomena in high temperature metallurgical processing operations. This paper presents results from the author’s experience with instrumenting thermocouples in copper elements coated with carbon to infer velocity of high temperature liquid metals. It also presents a methodology to determine velocity of a high temperature liquid by inferring the local heat transfer coefficient at a solid-liquid interface

Jan 1, 2015