Search Documents

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By D. Raicevic

After more than 93% of the uranium is extracted from Elliot Lake uranium ores by a sulphuric acid leaching process, the leach residue (tailings) contains small amounts of uranium and radioactive isotopes, particularly radium-226, which is the most serious health hazard. Heavy metal components and pyrite are also present, along with the gangue minerals. Currently, over /000 acres of the Elliot Lake area are covered with these tailings, which contain over five million tons of pyrite. Because of constant oxidation of the pyrite by bacteria (thiobacillus) and the presence of moisture, pyrite slowly generates sulphuric acid, which steadily leaches the metal-bearing constituents from the tailings. The seepage-flows of the dissolved contaminants, although often quite low in volume, have an environmental impact on the Elliot Lake area. Although these seepages are treated and most of the contaminants removed and impounded, a small amount of the radioactive contaminants reaches Lake Huron via the Serpent River. This paper describes a flotation approach for treatment of the Elliot Lake uranium tailings to produce new, decontaminated tailings practically free of pyrite, with radium, thorium and uranium contents considerably reduced. The decontaminated tailing produced, which comprises about 75% by weight of the current uranium tailings, appears to be suitable for mine backfill. Because mine backfilling normally uses about 50% of the plant tailings, the surface storage of about half of the uranium tailings, therefore, would be eliminated by this process. Mine backfilling would also increase the mine production and thus enlarge the over-all uranium resources due to recovery of the ore from pillars. The pyrite concentrate produced from the current uranium tailings would be suitable for sulphuric acid production. The possibility of uranium recovery, and disposal of radium and thorium from the concentrates produced, is now being studied at CANMET.

Jan 1, 1979

By Ward E. Kilby, Bruce I. Mcclymont

"Data from the South Fork Pit Area of the Bullmoose deposit in northeastern British Columbia are used to demonstrate the usefulness of microcomputers to the on-site geologist. The technique utilizes a series of digital surf aces in the form of a network of points to define various geologic parameters such as seam positions, topography and coal quality characteristics. Manual digitizing, kriging and combinations of these techniques are used to calculate these digital surfaces, the best method depending upon the type and quality of the data in question. Digital surfaces, each modelling a specific feature when combined and manipulated with the computer form a powerful tool, the deposit model. The resultant model, containing all the surfaces, is used to examine seam and inter-seam thicknesses, deposit volumetrics, seam quality characteristics and the adequacy of sampling.IntroductionCoal deposit modelling using computer-based techniques has become routine. However, a geologist working in the field, without access to mainframe or minicomputer, ha s considerable difficulty implementing these procedures. However, microcomputers, which are portable and inexpensive can handle exploration data, perform various geological analyses, and produce deposit models virtually at the same time as the data is being collected. For the on-site geologist this means that quick access to the results of such modelling could point out inadequacies in deposit definition and trends in coal quality deserving investigation."

Jan 1, 1985

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By David L. Anderson

"The government o f Canada has, since 1981, been under intense political pressure to modify its foreign direct investment (FOI) regulatory regime(1). To date the government's response has been limited to administrative and ""cosmetic"" changes: substantive issues have been largely ignored(2). However, as long as the economy continues to flounder , the Foreign Investment Review Agency (FIRA), as it is presently formulated , will continue to be an easy target for government critics . This phenomenon, in conjunction with the virtual certainty of a federal general election within two years, suggests that changes to the FIR Act will be seriously entertained by the present government.Recent events indicate that if change s are made, they will likely entail the adoption of a special-sector approach within the existing framework of a general screening system(3). Since this approach is currently employed in Australia(4), it would seem to be appropriate, from a public policy perspective to study that country's experience in developing and operating such a scheme. In doing so, I shall focus on the mineral sector; the rationale for doing so is as follows. First, this sector served as the focal point of the Australian FOI regulatory debater(5), Second , with the exception of the oil and gas industries, the non-petroleum mineral sector is one of the few areas of the Canadian economy wherein the Trudeau government has adopted an explicit domestic ownership target(6). Third, the non-petroleum mineral sector is, undoubtedly, a prime candidate to be denoted a s a special-sector if such a framework were to be utilized by the Canadian government!"".Although international comparisons are fraught with danger , a Canadian/Australian comparison is particularly appropriate(8). Both countries have reasonably similar economic, political and social structures . Furthermore, as noted above , Australia is the only other western country which employs a general screening mechanism for FOI. In addition, it utilizes a special area approach ; within this scheme, an explicit target of a minimum of 50% Australian ownership of all new resource projects has been formulated and clearly promulgated to all of the relevant interest groups. This policy, broadly defined, has been in place for more than six years and during this time the Australian mineral sector has, by world standards, prospered(9). Hence, the Australian experience in designating the mineral sector as a key area within a general screening system, should be of interest to Canadian policy-makers."

Jan 1, 1984

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984

By Nichols. R. S.

"Surface coal mining production from Elk Valley and area in southeastern British Columbia began in 1913. Since 1970, five open-pit mines have been put into production: Westar Mining&apos;s Hanner and Greenhills Operations; Fording Coal&apos;s Fording River Operation; Byron Creek Collieries&apos; Coal Mountain Mine and Crows Nest Resources&apos; Line Creek Operation.ln 1983 these mines produced 14.9 million tonnes of raw coal at an average strip ratio of 4.9 bank cubic metres of waste to 1.0 tonne of raw coal. This is 70% of the estimated 21.1 M tonnes annual capacity .Multiple seams are recovered with truck/shovel and dragline equipment. There is a wide range of equipment types in use with a recent trend toward larger and more mobile equipment.Coal mining in Elk Valley involves advancing along strike in four steps: hangingwall waste removal; seam cleaning; coal recovery; and foot wall waste removal. Each mine is unique in its approach to these four steps but the truck/shovel methods can be categorized into three main groups: seam dips < 35 degrees as at Harmer, Fording and Greenhills; seam dips 35 to 50 degrees as at Line Creek; and seam dips >50 degrees as at Byron Creek. Dragline mining at Fording involves bath waste and coal removal by draglines."

Jan 1, 1984

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system&apos;s inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By A. C. Moerman, C. W. Pelley, K. R. Notley

"The software package described in this paper facilitates the handling of diamond drilling information in the creation and maintenance of a geological information database. Once entered, the drilling information is stored in a direct access file for rapid retrieval. The drill data are sorted into vertical cross sections and interpretation is performed using on-screen menus to define areas of common rock type and outline the mineralized zones. Intersections of individual zones can then be examined and outlined in the longitudinal dimension at a graphics terminal.With the aid of surface-fitting routines, the digitized information can be used to generate three-dimensional models of each zone. From these models intermediate cross sections and level plans can be obtained. Several interpretations are possible and plotter drawings can be obtained. An output file for use by ore reserve estimation software can also be created.Future work will tie this software to geostatistics and mine planning programs and will be aimed at converting mainframe software to run on microcomputers. IntroductionComputer applications in underground mine planning and geology are not new. Operations such as Sherritt Gordono and Kidd Creek have been using software developed about a decade ago for handling geological information and designing stoping blocks. However, general use of such systems has been limited mainly due to the cost of hardware which was affordable only to large corporations. Software to perform the work was usually developed on site and was largely unavailable for use by others, being site-specific, or too expensive for other organizations to purchase.The increasing power of microcomputers and mini-computers, and their relatively low cost compared to the mainframe computers which were previously used, has led to the increased use of computers at mining operations of all sizes. Sources of software for use in geological interpretation and mine planning have increased in number with the proliferation of the use of microcomputers."

Jan 1, 1988

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By D. A. Trotter

"Low-pressure sodium light sources have been available for several years, but have not received wide acceptance in underground mining. This is because they are difficult to operate using DC power, they are not an intrinsically safe light where explosive gases may be encountered and they give poor colour rendition.With the need for energy conservation, several Canadian hard-rock metal mines are now changing their lighting to low pressure sodium, as it has the highest efficacy of any light source in terms of lumens per watt. Studies have pointed out several other advantages as well. Glare can be controlled, they penetrate fog well, they are easily maintained, they have a long life and they give the highest visual acuity when compared to other types of lighting. As well, in an underground mine, contrast is much more important than colour for task identification. For close work, the colour problem is alleviated with the use of cap lamps.Case studies are presented from Canadian practice. These show how the lights are modified for underground use, calculations preceding light installation, and how and where the lights are installed in the underground environment. Mention is made of worker reaction to the lights and possible physiological effects.IntroductionThe importance of good underground lighting to the total environment of mining cannot be overemphasized. In addition to the obvious benefits of improved worker morale, available studies show that good lighting practices reduce accident severity and frequency as well as increase production."

Jan 1, 1982

"Technological innovation is an extremely complex activity. The author presents his interpretation of innovation and the innovative process. He reviews the strategy used by participants in coal mining innovation in the past and discusses changes required to meet the challenges of the future.Introduction if an industry is to be successful and viable in today&apos;s world, the companies active within the industry must remain close to the frontiers of knowledge. The coal mining industry is no exception. Technological problems facing the coal mining industry are basically economic and social. Economic problems are those concerned with the long-term growth and profitability and social problems, with the health and safety of the mine worker and the impact of the mining operation on the environment.Technological innovation can be a key factor in meeting these problems successfully. The general belief is that the information base for technological innovation exists within mining companies and governmental agencies but current industrial and governmental strategies and structures impede the transformation of this knowledge into the mining products and processes required for growth.The purpose of this paper is to determine where Canada is in terms of coal mining on the innovative ladder. The paper as presented: defines innovation and innovative process; gives an historical ""broad brush"" review o f innovation in the industry; and suggests the challenges to be faced in the future."

Jan 1, 1985

By Henry Brehaut

"It is difficult to know how much environmental information is absorbed by those in a position to put it to use. The following information may seem like ""old stuff"" to those whose companies are taking steps to improve their environmental performance. This paper is directed in particular to those people who are interested in determining what further changes are required to make improvements as concerned environment citizens.IntroductionUntil recently, the author was comfortable with the fact that none of the operations for which he was responsible had any environmental charges against them. It was not until one of his operations was charged with non-compliance that the author discovered due diligence as a way to avoid a second charge, and when an unfortunate spill occurred at another operation, the meaning of risk prevention was learned. Knowledge was gained step by step to the point where finally environmental information is being heeded, rather than waiting to learn from sad experience. With the appreciation of what it takes to do a good environmental job, comes an understanding of the challenge that lies ahead, and the fact that there is a lot to learn.At a recent environmental gathering, comments from the participants varied considerably. Some just didn&apos;t understand why government was being so unreasonable, while at the other end of the spectrum one individual whose company was well along the path to becoming a good environmental citizen remarked that it was all very basic. What was immediately understandable to one went right over the heads of others, indicating the different stages that have been attained in the acceptance of environmental responsibilities."

Jan 1, 1991

By James E. Fisher, Roger Cotton

"The legal background f or environmental issues, and the growing emphasis both from government and private concerns of corporate and management liability for environmental problems provides one of the driving forces behind the growing concern with environmental law for the future. One prime objective must be the identification and minimization of potential liability, both for the corporation and its officers, directors and employees.This paper will identify the basis for liability of individuals and corporations for environmental matters, focussing on current legal requirements, and the appropriate legal response to events of such potential liability. It will also consider the reduction of liability through the implementation of management systems and environmental policies in order to ensure due diligence both with respect to corporate responsibility and the responsibility of the individuals within the corporation.IntroductionConsolidated Professor Mines Ltd . and its predecessor have been exploring in northwestern Ontario for about sixty years . During the last twenty years, the company has been interested in developing a gold mine, the Duport Project, on Stevens Island in Shoal Lake . The lake straddles the border between Ontario and Manitoba and is a drinking water supply for Winnipeg and environs.The Duport Project involves the mining of 450 t/day grading an average of 0.35 oz Ault of ore . At the minesite, located on Steven s Island in Shoal Lake, only preliminary processing of the ore will take place, to produce gravity and flotation concentrates for final gold recover y at a mainland plant well removed from the Shoal Lake watershed. No hazardous chemicals will be used at the island site."

Jan 1, 1991

By M. Beech-Jones

The increased emphasis on the efficient utilization of capital and mineral resources has led to several new advances in the science of mineral separation. One example of a recent development is the application of high-capacity high-intensity wet magnetic separators to fine hematit e recovery by a leading Canadian iron ore producer. The iron ore recovery feasibilit , flow-sheet development, circuit operation and metallurgical performance are reviewed.

Jan 1, 1979

By Akira Fujisaki

"The oil crisis accelerated the change of non-ferrous metals&apos; demand structure. Maturing societies in developed countries and preference for lighter, thinner and smaller products are eroding the non-ferrous metal industries&apos; growth potential. Inventory-control, stockpiling and developing new demand are measures Japanese smelters have taken to cope with the changing demand.The most effective means for risk management of product demand lies in the cooperation between ore producing countries and metal consuming developed countries to assist developing countries in their efforts to ""take-off"", which in turn will bring about a surge of demand for metals.SummaryThe non-ferrous metal industry in the world is suffering its most serious slump since the war. With some of the markets of the advanced industrialized countries approaching saturation point and economized usage of natural resources and substitution growing, the possibility of a quick recovery of the demand for base metals is dim.To cope with the changing product demand Japanese producers have had recourse to such measures as strict inventory control and stockpiling for the purpose of stabilized imports. They have also tried hard for securing raw materials and promoting new field s of demand but the very core of ""risk management"" has been the diversification of line s of business to bolster and stabilize the foundation of management of the non-ferrous metal industry in Japan.To see the demand for nori-ferrous metals recover from the slump and be put on a path of solid development, we have to wait for the economies of the developing countries to ""take off"" and for its realization the economies of the developed countries must be reactivated with new growth industries playing a leading role, and the transfer of technology and money recycling must be carried out smoothly under an orderly international trade system."

Jan 1, 1983

By M. R. Swaan, G. J. Stewart

"ABSTRACTThe application of failsafe techniques to ask the ""What if"" questions about any process has been well established in the chemical industry for many years. The unusual number of fatalities that occurred in Ontario during 1986-87, prompted Inco management to look at the Fail Safe techniques as a method of improving safety performance.INTRODUCTIONOne of the major areas at any time for potentially disastrous accidents is the shaft, where all men and materials must travel. In April 1987, Inco&apos;s Thompson Mine&apos;s first Fail Safe Team was established to look at its shaft operations. The initial group of eight people was made up of hourly equipment operators, mine foremen, engineering, maintenance and the superintendent. This group took the name of Shaft Risk Analysis Team or SRAT.The many tasks or jobs that are performed in a shaft prompted the team to divide the work under six major headings; slinging, moving men, skipping, dewatering, shaft inspections and moving materials. Each of these areas contained many different tasks which are interrelated. The only way to understand this interrelationship was to flow chart the steps that actually occur in getting any job done.The flow charting is done by the foreman and operators using existing standard manuals and their experience of what actually takes place. In many cases, it soon became apparent that they had been ""working around"" many problems created by their standards. Fine tuning of these flow charts takes place at the weekly meetings, where input from all involved leads to a better understanding of the actual job being analyzed and its potential hazards. Two major points need to be emphasized in getting good flow charting at a mine:I. It must never be blame oriented or you will never discover how the jobs are actually done and hence you won&apos;t know what to improve.2 . All team members must have equal voting rights in deciding how to put the charts together so that they have ownership of the finished product. It is far too easy to end up with amanagement view of the way it should be. Many different techniques or methods are being employed to improve the tasks and reduce the risks associated with any job once the basic flow chart is established. The ones found to be the most useful are highlighted."

Jan 1, 1989

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007