Search Documents

By Kamran Esmaieli

This paper investigates the behavior of ore pass walls under impact loads caused by material transiting through an ore pass. In particular it considers the influence of foliation in the rock mass surrounding an ore pass as both a triggering and accentuating cause of degradation. Based on empirical observations in several underground mines a numerical experiment was designed to understand the influence of rock mass foliation on impact-induced damage on ore pass walls. The distinct element method, and in particular the Particle Flow Code (PFC2D) was used to simulate three different rock masses surrounding an ore pass. Each simulated rock mass has similar properties but was defined by distinct dominant foliation (70o, 80o, 90o) along the foot wall. The numerical experiments investigated different scenarios whereby the walls were loaded by a projected rock fragment striking the foliated walls at a constant impact angle and velocity. The damage inflicted by the projectile rock fragment, on the foliated rock mass, was quantified using the number of impact-induced micro-cracks initiated on the ore pass wall. The results of the numerical analysis indicated that the presence of foliation resulted in greater damage zones in the surrounding rock mass. In addition, the extent of impact-induced damage to the ore pass wall increased as the angle of interception between the ore pass wall and the rock mass foliations decreases. This is in agreement with qualitative field observations.

Jun 1, 2012

By J. Zou

Open-cut method is most widely used for shallow utility lines installation. In urban areas, unexpected utility lines buried underground potentially turn open-cut construction into a highly risky operation, increasing the construction cost while presenting additional safety hazards. Examples include: breaking existing water main leads to flooding the downtown area; hitting an unexpected gas line causes an explosion. To prevent those accidents, the current practice is to stake out the underground utility lines before the open-cut construction based on the as-built information collected from various utility companies and government agencies. However, the as-built information is not always complete and accurate. To verify the locations of some important utility lines and protect them against damages caused by open-cut construction, new techniques and technologies are used but have their limitations in revealing underground utility lines, such as hydro vacuum method and ground penetration radars (GPR). The emerging technology of ultra-wide band (UWB) radar holds the potential to provide a cost-effective, non-destructive detection method. In this paper, a critical review of current practices and established methodologies is given. The functionality and working mechanism of UWB radar technologies are described. Application potential in open-cut construction is demonstrated by conducting lab experiments. Testing set-ups for detecting unexpected utility lines in soil along with preliminary results are presented. The effects of soil moisture content on the detection range are discussed. Research findings are summarized and constraints are discussed in conclusions.

Aug 1, 2013

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By C. W. K

This little sketch of the late Willet G. Miller, Provincial Geologist of Ontario, is intended to be neither a biography of his career nor a eulogy of his life. His biography has already been written in an incomparable manner by Mr. T. A. Rickard, his eulogy by Canon Cody. What more can be said of Dr. Miller than is summed up in the words of that great Canadian divine, Canon Cody, that he was "Big in body, big in heart, and, as we learned, big in brain." This article, then, will merely record a few personal reminiscences of the man himself, and while they are necessarily disjointed, they may at least serve to illustrate certain traits in his character which are not generally known or appreciated outside of the circle of his intimate friends. In the latter part of May in the year 1904, Willet G. Miller, with two? assistants, set out for the small village of Haileybury to begin his geological work in the area a few miles to the south which he was soon to name Cobalt. At that time the Timiskaming and Northern Ontario railway was not finished, although the right-of-way was cleared and partly graded. The nearest railway station was on the Canadian Pacific at the south end of lake Timiskaming, from which point the old steamer Meteor carried passengers and freight up the long, narrow and deep waters of lake Timiskaming, a very pleasant trip of some sixty miles. On this particular trip there was a fairly large crowd on board consisting of settlers going into the clay belt north of lake Timiskaming, of lumbermen, and of a few merchants and commercial travellers who were interested in the small business centres of Haileybury, New Liskeard and Ville Marie. Scarcely any attention was paid to the reports of the newly found silver deposits, although the daily papers had announced discoveries in the district six months before. As a matter of fact, the chief excitement on board was afforded by a moose, which, in swimming from the Ontario to the Quebec shore of the lake, crossed the bow of the boat, the captain steering to within a few yards of the terrified animal.

Jan 1, 1925

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By Craig Dirk

Agenda Applications of ?GPS ?Drill Navigation ?Cycle time monitoring ?UDS / Boom Stress monitoring ?Payload systems ?Laser Surveying Future Applications

May 1, 2006

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By D. Monder

Fuel cells are promising sources of electrical energy because of their exceptionally high efficiencies and low environmental emissions. Solid oxide fuel cells (SOFC) are high temperature, ceramic electrolyte cells, which unlike most other fuel cells, can work with a variety of fuels besides pure hydrogen, including hydrocarbons and hydrogen sulfide. In this presentation I present the models we have built for a single H2S fuelled SOFC. The goal is to model the electrochemical reaction coupled with mass transfer, fluid flow and current/voltage distribution in an yttria stabilized zirconia electrolyte fuel cell assembly operated between 750 and 850 °C. Two models of the above SOFC are discussed in this work, 1) an algebraic model derived by integrating a one-dimensional model along the thickness of the cell, and 2) a two-dimensional finite element axi-symmetric model. Important physical and kinetic parameters in the 1-D model are fitted using experimental data sets at three different temperatures and reasonable fits are obtained for the data sets at 800 °C and 850 °C. However, the third data set at 750 °C does not give a good fit using this model. We need to apply the curve-fitting to more data sets to investigate it further. The main conclusion that can be drawn from the present study is that the ohmic resistance of the cell is very high. Contact resistances are believed to be the reason behind this although there could be contributions from resistive interphases. The 2-D model also gives reasonable fits to data sets. One of the publications by the laboratory group doing the experimental work in our department presented very interesting data that shows the cell performance being a strong function of fuel flow-rate. We want to model this behaviour and will have to depend on the 2-D model as the 1-D model does not have flow-rates as parameters.

Jan 1, 2005

By Normand Champigny

The Forces of Change ? The current business environment ? What can we expect for the future on management of physical assets ? The impact of maintenance on production costs ? What is RCM is doing is improving business performance ? The beginnings of RCM The RCM II Process ? RCM II is a structured process that involves employees in determining the best failure management tactics for systems and equipment in their operating context ? The method is an effective approach to risk and cost reduction as well as failure management

May 1, 2002

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By T. C. Holmes

Introduction The Dome mine, in the Porcupine mining camp of northern Ontario, is one of the important gold mines of the country, having produced over 139 million dollars worth of gold from the commencement of production in '1910 to the end of 1944. The geology of the mine is complex and a number of types of ore are known, each occurring under particular conditions. The mine workings are very extensive and by far the greater part of them have been geologically mapped only in reconnaissance fashion. By 1940, when the writer joined the mine staff, the orebodies in the sedimentary trough and the 'nose' orebodies, the first types to be developed, were almost worked out and many workings were inaccessible, so the descriptions of these types are based largely on study of the plans and records. The same applies to a lesser extent to some other types. At various places in this paper, statements are made as to the mineralogical or chemical composition of the rocks. Most of these determinations are based on examinations made with a hand lens and cannot, therefore, be regarded as very reliable. General Geology As there are several types of ore in the mine, occurring under quite diverse conditions, a brief outline of the geology is given here, sufficient to provide a general picture into which the fuller descriptions given with each type of ore can be fitted.

Jan 1, 1947

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract - MEGATEMII airborne electromagnetic data collected over the Iso and New Insco massive sulfide deposits have been modeled using three modeling packages. The EMQ package is a quick inversion tool which indicates that the Iso body is a dipping, plate-like body. The New Insco body is inferred to have a geometry somewhere between a dipping plate and a sphere. The Maxwell package was used to refine the properties of the plate-like body at Iso. The EMIGMA package was able to identify which parts of the New Insco orebody were more conductive. It was observed that the most conductive parts correspond to copper-rich zones and the next most conductive to pyrite-rich zones. The EMIGMA package was also used to show that a thick-prism model might be more appropriate for the New Insco orebody. Gravity modeling constrained by the known geology was successful in identifying the denser sulfide zones. The densest zones appear to be pyrite rich. Magnetic modeling identified diabase dikes. Over New Insco, a small magnetic anomaly was attributed to pyrrhotite-rich sulfides. There was only a weak magnetic anomaly over the Iso body, consistent with the nonmagnetic sulfides logged in the holes drilled at that location. Sommaire - Les données MEGATEMII recueillies au-dessus des dépôts d’Iso et de New Insco ont été interprétées en utilisant trois outils de modélisation différents. L’outil EMQ a été utilisé comme un outil d’inversion rapide suggérant que le dépôt Iso peut être considéré comme une plaque inclinée, et que le dépôt de New Insco se situe quelque part entre une plaque et une sphère. L’outil Maxwell a été utilisé pour raffiner les propriétés du dépôt Iso. L’outil EMIGMA nous a permis d’identifier les différences de conductivité à l’intérieur du dépôt Iso. Il a été observé que la partie la plus conductrice correspond à la zone riche en cuivre, suivie par la zone riche en pyrite. L’outil EMIGMA a aussi permis de montrer qu’un modèle de prisme épais pourrait être plus approprié pour décrire le dépôt New Insco. La modélisation des données gravimétriques, contrainte par la géologie connue, définit bien la zone de sulfures massifs. La zone de pyrite semble être la plus dense. La modélisation des données magnétiques identifie bien les dykes de diabase. Au-dessus du dépôt New Insco, on observe une faible anomalie magnétique correspondant aux sulfures non magnétiques observés dans les carottes de forages à cet endroit."

Jan 1, 2006

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971