Search Documents

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By F. Duan, J. Pfarr, J. M. Goris

"The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co. and the University of Utah, is conducting a field demonstration to evaluate the behaviour of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-48N stope, 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behaviour of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modelled using the finite-element code UTAH III. Field data will be used to verify the modelling. In addition, a comparison between the effectiveness of conventional and birdcage cables will be made.45-48N StopeThe 45-48N stope is located in the 21 ledge between the 6500 and 6650 levels and contains about 233 000 short tons of mineable ore. The orebody lies within the Homestake Formation and is very irregular being approximately 200 ft long and 75 ft wide. Between the 6500 and 6650 levels, it dips from 35 degrees to 60 degrees east with a near-vertical plunge to the south. Mineralization is characterized by arsenopyrite and pyrrhotite with minor gold. The contact between the Homestake and the overlying Ellison Formation creates a plane of weakness along localized graphitic layers. The footwall dips at approximately 60 degrees but between 100 ft and 120 ft above the 6650 level , the hanging wall flattens to almost 20 degrees causing a significant mining problem."

Jan 1, 1991

By J. J. McDougall

Until quite recently, the coal in the Cape Breton field was won from comparatively thick seams with light cover, and from submarine areas, and the system of mining naturally followed was pillar-and-stall. This sytem permitted of cheap extraction, and enabled production from localities where other methods could not be employed to good advantage. Thus the pillar-and-stall system, applied to conditions as stated, justified its adoption. Our working seams today, however, are practically all under heavy cover, or are moving in that direction, and with this gradual increase in cover came the increased cost of roadway maintenance. At Princess colliery, the system of pillar-and-stall was followed until roof and bottom conditions became such that further operations were unprofitable, and the longwall method was then adopted as an economic necessity. This fact should be borne in mind when operating costs of both systems are being compared. The longwall method is not held as a cure for all difficulties of heavy cover, but through it these difficulties can be overcome with less expense than by pillar-and-stall. The longwall system of mining, strictly speaking, is one by which a seam of coal is totally extracted in one operation. There are, however, many modifications of longwall, and in some cases it is difficult to determine whether certain practices should be classed as longwall or pillar-and-stall, or a combination of both.

Jan 1, 1928

By O. Rabeau, M. Legault, F. Fallara

"Abstract - The development of robust 3-D geological models involves the integration of large amounts of public geological data, as well as additional accessible proprietary lithological, structural, geochemical, geophysical, and diamond drill hole data. 3-D models and maps have been available, particularly in the petroleum industry, for more than 10 years. Here, we demonstrate how robust 3-D maps can be used as interactive tools for mineral deposits exploration. In particular, we show how the interrogation of 3-D data sets can constrain exploration targets at depth. The main advantages of this technique for the mining industry are the homogeneity of data treatment and the validation of geological interpretations, taking into account geophysical and geochemical data. Data integration and cross-correlation of geology and geophysics can be achieved in two dimensions in any good GIS package. However, the added strength of 3-D analysis is the integration of separate data sets in three dimensions to build more complete, more realistic models, and in delineating areas of high economic potential at depth. Furthermore, these models can be modified and improved at any time by adding new data from ongoing drilling and geoscientific surveys. This paper presents two examples of 3-D models used for mineral exploration: the Joutel VMS mining camp and the Duparquet gold camp, Quebec. In both examples, the creation of the model is discussed and queries specific to the relevant exploration model are introduced. Eight potential exploration targets are generated at Joutel and seven at Duparquet. Although the targets defined are dependent on the details of the chosen queries, it is apparent that this technique has the potential to generate promising exploration activity that can engender new targets. Sommaire - Le développement de modèles 3-D géo-intégrés fiables implique l’intégration de grandes quantités de données géologiques publiques ainsi que des données lithologiques, structurales, géochimiques, géophysiques et de forages en provenance du secteur privé. L’industrie pétrolière dispose de modèles et de cartes 3-D depuis plus de 10 ans. Ce manuscrit présente un exemple d’utilisation de modèles et de cartes tridimensionnels détaillés comme outils interactifs dans l’exploration de dépôts métallifères. L’emphase est mise sur le processus d’interrogation des données en 3-D pour la définition de cibles d’exploration en profondeur. Les avantages principaux de cette technique sont l’uniformité du traitement des données et de la validation des interprétations géologiques, tout en tenant compte des données géophysiques et géochimiques. L’intégration de données et la corrélation de la géologie et de la géophysique peuvent être accomplies en deux dimensions dans n’importe quel logiciel SIG. La plus grande force de l’analyse 3-D demeure cependant la possibilité de construire des modèles complets et réalistes permettant de cibler des secteurs à haut potentiel économique en profondeur. De plus, ces modèles peuvent être modifiés et améliorés de manière interactive en ajoutant de nouvelles données provenant de forages et de levés géoscientifiques en cours. Ce manuscrit présente deux exemples de modèle 3-D géo-intégrés développés pour l’exploration minérale : le camp de SMV de Joutel et le camp aurifère de Duparquet, Québec. Dans les deux cas, la construction du modèle est décrite et les requêtes spécifiques à chaque type de gisement sont présentées. L’exercice a permis de définir huit cibles d’exploration potentielles à Joutel et sept à Duparquet. Bien que les cibles identifiées dépendent des contraintes utilisées pour les requêtes choisies, cette technique permet de générer de nouvelles cibles qui pourraient relancer l’activité d’exploration dans les camps miniers " matures " ou dans des secteurs moins explorés."

Jan 1, 2006

Microseismic (MS) methods offer one of the few ways to monitor a 3D volume of rock and essentially see into the rockmass and the regions of real time rock fracture. This is a critical component when considering workplace safety as well as the economic viability of a mining operation. New Gold Inc. New Afton Mine, an intermediate copper-gold mining company located 350km northeast of Vancouver in the south-central interior of British Columbia, Canada, has recently installed a MS system to help understand the block caving process in space and time. For a block cave mining operation is it important to utilize the MS events to map out the seismogenic zone related to the regions of stress concentration and fracturing mechanisms which lead to caving. The geological setting within the local array is complex, consisting of several distinct lithologies with unique material properties that each affect the microseismic signal differently. The block cave consists of a muck filled void, also affecting the seismic waveform path. This paper compares the use of a single velocity model to a variable velocity model which accounts for the differing lithologies and cave. The variable velocity method determined 3D raypaths for all source to receiver possibilities through five irregular shaped geological domains and the estimated cave. For calibration blast data, the variable velocity model is found to successfully decrease the error for event location from an average of 38m to 20m (47% improvement), and its importance to location accuracy is expected to increase as the cave develops in size.

Aug 1, 2013

By V. Feldman, I. Holl, J. Zampini

"The Renard Mine, 100% owned by Stornoway Diamonds, is located approximately 250 km north of the Cree community of Mistissini and 350 km north of Chibougamau in the James Bay region of north-central Québec. The project benefits from a large and growing resource, good mining conditions, strong social acceptance, a modest environmental footprint, and the development of direct-to-mine road infrastructure. Construction began on July 10, 2014; following the completion of a 946 million CAD project financing transaction. Now completed, the mine is the first diamond mine in Québec, and one of only six in Canada, employing approximately 500 people. First ore was delivered to the plant approximately 5 months ahead of schedule on July 15, 2016. Commercial production was declared on January 1, 2017. In general, the project ramp up has been characteristic of a type 1 McNulty curve. One of the challenges during production ramp-up was a redesign of processed kimberlite dewatering (replacing the dewatering centrifuge with two stages of hydrocyclones and a dewatering screen). A processing opportunity captured by Stornoway was the design and installation of an ore sorting facility which rejected free waste rock from the valuable host rock; kimberlite. Through tackling both challenges and opportunities, Stornoway has realised and is now exceeding their original design tonnage.PROJECT DESCRIPTION Stornoway Diamond Corporation (Stornoway) was established in 2003 resulting from to a plan of arrangement between Northern Empire Minerals Ltd. and Stornoway Ventures. In 2011, Stornoway acquired 100% interest of the Renard Mine. The construction of the Renard Mine began in 2014 and achieved full production in 2017 [1, 2]."

Jan 1, 2019

By C. A. Pickles, K. Mackowiak, D. Gajonera

"Shake-flask oxidation tests were performed on Red Dog mine waste to study the initial dissolution behaviours of lead, zinc, and iron. The conditions for accelerated acid generation in terms of Eh and pH were determined. Each mineral behaved distinctly, with galena dissolving first, followed by sphalerite, then pyrite, although there was some overlap in behaviour. Iron was not detected in solution until approximately day 40 and was present at low concentrations. The experimental conditions and the theoretical model results indicated the formation of iron oxyhydroxides at low weathering times and jarosite at longer times.RÉSUMÉ Des tests d’oxydation par agitation en flacon ont été effectués sur les déchets miniers de l’exploitation Red Dog afin d’étudier les comportements initiaux de dissolution du plomb, du zinc et du fer. Les conditions entraînant la production accélérée d’acide en termes d’eH (potentiel d’oxydoréduction) et de pH (potentiel d’hydrogène) ont été déterminées. Chaque minerai se comportait différemment ; la galène a été la première à se dissoudre, suivie de la sphalérite, puis de la pyrite, mais un certain chevauchement des comportements a été observé. La présence de fer en solution n’a été détectée qu’après environ 40 jours et ce, à de faibles concentrations. Les conditions expérimentales et les résultats du modèle théorique signalaient la formation d’oxyde-hydroxyde de fer sur de courtes périodes d’altération atmosphérique, et de jarosite sur des périodes plus longues."

Jan 1, 2017

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By L. V. Chugaev

In the course of the hydrothermal refining of copper-nickel products containing covellite, oxidation of Fe2+ ions by the CuS?Cu2+ pair takes place, and iron is precipitated as hematite. Lower copper concentrations in the solution and higher solution acidity lead to the partial oxidation of sulphide sulphur, whereupon hematite is reduced by covellite causing iron to go back in solution. It is demonstrated that in the process of hydrothermal treatment of the covellite-containing solid product in pure water covellite oxidises millerite to polydymite (Ni3S4). Formation of polydymite during the process of refining seems to be due to millerite oxidation both by covellite and the CuS?Cu2+ pair.

Jan 1, 2007

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011

?Podolsky Water treatment plant discharges to Norman North bog which drains into Whistle / Post Creek watershed and into Wanapitei Lake ?Whistle Mine closed and reclaimed but continues to treat and discharge water to Whistle Creek

May 1, 2009

By J. F. Hazzard, R. J. Chalaturnyk, C. Khazaei

"Various measurement, monitoring and verification (MMV) techniques are used to ensure the safety of operations in petroleum projects. One of these techniques is microseismic (MS) monitoring of the caprock. A challenge in MS monitoring of caprock is that unlike projects such as tunnelling in hard rocks, the number of recorded events are much smaller and also wide spread through the rock mass which makes interpretation of the physical meaning behind the events very difficult.In this paper, a numerical technique is introduced and validated for coupling a finite difference code, FLAC3D (Fast Lagrangian Analysis of Continua), with a discrete element code, PFC3D (Particle Flow Code). Then, a similar approach is adopted for modeling microseismic events in the caprock. For this purpose, the underburden, reservoir and overburden layers are modeled by FLAC3D. A rather small section of caprock above the reservoir is nulled in the FLAC3D model and substituted by a PFC3D inclusion. The reservoir pressures are then applied to the reservoir section of FLAC3D. Once the FLAC3D cycles, there will be induced pressures in the caprock due to its undrained response to the change in pressures within the reservoir. These induced pressures are transferred to PFC3D as boundary velocities. Then the PFC3D cycles and sends back the boundary forces to FLAC3D. This back and forth process continues until equilibrium is reached. During this process, there will be bond breakages within the PFC3D inclusion that can be regarded as MS events. An algorithm for recording the microseismic energies based on a change in local strains is also implemented. The results are then compared with real data. The effect of injection fluid temperature is also studied. No significant appearance of microseismic events was observed due to injection of CO2 in both cases (i.e. with or without considering temperature). However, this continuum/discontinuum approach seems promising for understanding the microseismic response of caprock in more detail and also using the MS data for validation of geomechanical models."

Jan 1, 2015

By R. H. McCorkell

"Sample drops were evaporated on Lexan disks on which fission tracks were etched and counted after neutron irradiation. [U] = 0.01 ppb could be measured. This method is rapid, cheap, simple and accurate when sufficient control and checking is possible, but several types of error were encountered in its use, the natures and sources of which were investigated but not always determined. The most troublesome were ""annealing"" processes which sometimes altered the fission tracks so that they were not fully revealed, or acquired varying appearances, after etching. Several different annealing processes seemed to exist and seemed to be produced by alteration of the Lexan surface by dissolved components in the solutions and, perhaps, by radiation and local heating during neutron irradiation. The appearances of the etched tracks varied with the natures of the droplet solutions even when annealing appeared to be absent, and for this reason, standards are best prepared by additions of known amounts of U to sample solutions. Contamination of sample droplets by U-containing dust from the air is best avoided by preparing the disks away from areas where other U-analysis is being carried out.IntroductionFission tracks are regions of radiation dam age produced in solids by the fission of atoms such as 235U. They can be enlarged to sizes visible through optical microscopes by etching surfaces through which they pass with solvents in which the solids are slightly soluble. A sample to be analyzed for U may be placed against a film of a solid of negligible uranium concentration (the track detector) and irradiated with thermal neutrons in a nuclear reactor to fission 235U. The track detector is then etched and the number of tracks per unit area, ?, which is proportional to the uranium concentration of the sample, c, and the neutron do se, n, is found by counting through a microscope. Uranium in solutions ha s been measured by evaporating drops on track detectors, irradiating, etching and determining the number of tracks per drop, T(2,3,4,5). Extensive test s of this method are reported here."

Jan 1, 1983

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

By Jan W. Merks

The objective of metrology in mineral exploration is to derive unbiased confidence limits for masses of metals contained in reserves and resources. Sets of test results for gold and silver determined in pairs of interleaved bulk samples give unbiased confidence limits for the central value of each metal. The same sets of test results show how to verify spatial dependence by applying Fisher?s F-test to the variance of a set and the first variance term of the ordered set. A significant degree of spatial dependence gives a higher degree of precision for the central values of gold and silver. Plotting variance terms of an ordered set against the variance of the set and its lower limits of asymmetric 99% and 95% confidence ranges gives a sampling variogram. Sampling variograms put in plain view where spatial dependence in sampling units or sample spaces dissipates into randomness. The application of statistical methods to test results for sets of ordered core samples within boreholes, and for sets of ordered ore volumes within profiles, plays an important role in defining reserves and resources.

Oct 1, 2009

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012