Search Documents

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By G. B. Hobbs, S. Saimoto, L. Collins

"Plastic yielding and flow in metals is dependent on the microscopic process of simple shear along crystallographic planes and directions known as slip. Thus, by altering the crystallographic direction of the stress axis or placing constraints in the direction of plastic flow, anisotropy of yield strength for the same material is observed. This phenomenon is called texture strengthening. The application of this concept to highly anisotropic crystal structures such as the hexagonal group of titanium and zirconium alloys, the former in missile casing and the latter in nuclear reactor fuel tubing, seems obvious. The outstanding example in cubic structures is the case of deep-drawing steel. The R value, the width strain over the thickness strain during a tensile test, is taken as a measure of texture strengthening. In face-centred cubic structures, texture strengthening has been completely ignored on the basis that materials with R less than one are not amenable to this beneficiation. This study will review two aspects of texture which will lead to strengthening, first the thermal stability of the deformed microstructure, which is dependent on the stress axis, and second, the texture strengthening aspect of fcc metals.A review of recovery and recrystallization in textured aluminum wires, copper and cupro-nickel sheet will be presented with the view of extending these concepts to the manufacture of heat-exchanger tubing. The superior creep properties of specially processed commercial products such as TD-Ni, TD-NiCr and MAR-M200 will be shown to be a manifestation of the same physical phenomena."

Jan 1, 1981

By F. H. Samuel, H. Tahiri, S. Valtierra, H. W. Doty, A. M. Samuel

L'affinage des grains dans les alliages d'aluminium consiste à augmenter le nombre de sites de cristallisation de la phase a-Al afin d'obtenir une structure fine. Les alliages mères de type Al-Ti-B sont largement utilisés comme raffineurs des grains. Cette étude a pour but d'établir des mécanismes convenables d'affinage des grains dans l'alliage A356 en utilisant cinq alliages mères et deux températures de coulée (750°C et 950°C). Les résultats montrent que la phase a-Al prend une forme selon l'alliage mère ajoute; les échantillons coules a haute température montrent une taille de grain plus grosse; les températures de germination et de croissance augmentent avec I' augmentation du Ti ou du B et la taille des grains diminue. L'alliage mère Al-4%B montre une puissance remarquable en comparaison d'autres alliages mères. Pour cet alliage mère, le titane résiduel dans l'alliage A356 réagit avec le bore pour former TiB2 qui, par la suite, agit comme un germe actif pour la phase a-Al.

Jan 1, 2006

By L. Paulino, R. A. Camilli, J. Yamamoto, J. C. Araujo

The first paper presented on this work [1], showed how bath ratio was increased from 78% to over 95% using a structured approach to reduce bath chemistry variability. This update will illustrate the steps taken and update the results presented earlier, showing the effects of long power interruptions and several load reductions as well as load increase during the period from 1999 to 2005. Current efficiency was affected by such processes upset; however, bath ratio in range (±0.05) is still higher than 90%, even after an increment of more than 6 kA. This review will explain each of the steps taken to reach stability in this critical smelting parameter.

Jan 1, 2006

By The Mine Staff

THE PROPERTY of the Lamaque Mining Company, Limited, ?is located in the Town of Bourlamaque, seventy miles east of Noranda, in Bourlamaque township, Abitrbi county, north western Quebec. Gold production commenced at Lamaque in April, 1935, with an initial mill capacity of 250 tons per day. The capacity was doubled in November of the same year, and in December, 1937, it further increased to 1,200 tons per day. During the war years the mill operated at a reduced tonnage, but in 1951 milling units were added along with complementary crushing and shop facilities to bring the capacity to 1,500 tons per day. Finally, in 1953, the capacity was raised to 2,000 tons per day, which rate is being maintained at the present time. The total production at Lamaque from April 2nd, 1935, to December 31st, 1956, has been 9,168,901 tons of ore from which 2,208,168 ounces of gold was recovered. The total value of this production , excluding E.G. M.À.*, was $77,869,653.

Jan 1, 1957

By W. J. Cherones

This paper describes the history of the development and application of the electric mining shovel in open-pit mining, dea1ing particularly with far-reaching advancements in three primary areas: metallurgy, mechanical design and electrical systems. Hoist drives and crowd drives, including the Magnetorque and Electrotorque systems, and the integral propel drive are given close attention.

Jan 1, 1972

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By H. J. White

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel- base superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES® 282® alloy for applications in aircraft and land base gas turbines and other high-performance high-temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (~ 900 °C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability, and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/ repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R- 41, Waspaloy, and 263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, we present (1) results from hot ductility testing of annealed and annealed/aged material; (2) results from Time Resolved X-ray Diffraction (TRXRD) studies during a welding thermal cycle of annealed and annealed/aged material, and (3) gas metal arc (GMA) and gas tungsten arc (GTA) welding of annealed and annealed/aged material.

Jan 1, 2010

By J. Erik Scheel

Overview ? About Hard Creek Nickel ? Turnagain property ? Proposed power line ? Recent Preliminary Assessment ? Favourable economics ? Property Geology ? Mineralization and metallurgical characteristics of major lithologies ? Development of the acNi (ammonimum-citrate H2O2) technique ? Overview of necessary steps ? Results of the technique ? Conclusions

May 1, 2008

By B. Surender Mohan

Mining lignite pollutes the environment and causes ecological damage if unattended. Being conscious of the importance of environmental resources for the well-being of the living system, the Neyveli Lignite Corporation (NLC) adopts the policy of environmental regeneration as the foundation on which productivity is built. NLC started investing on Eco Care and Environment Protection long ago and it continues. Early investment in environmental protection has resulted in steady growth of the Company along with a healthy environment. The future vision of NLC is to be in the vanguard among the contributors to the community, environment and the nation by developing and utilizing industrial and human resources to the optimum. Untiring efforts are being put in mines (NLC as a whole) to maintain and sustain the ecological balance arising due to continuous mining activity. NLC?s Environmental Management System is becoming a symbolic role model for many of the opencast mines in Southeast Asia. NLC has been bestowed with number of prestigious Environment and Sustainability awards in recognition of the mammoth contribution in maintaining a clean and green environment.

Aug 1, 2013

By Marc R. Laflèche, Suzanne Paradis, A. Shirley Péloquin, Harold L. Glbson, Robin Potvin, Pierre Verpaelst

"The Archean Blake River Group is best known from a central volcanic complex in Rouyn-Noranda. This volcano-tectonic depression, delimited by the Hunter Creek fault to the north and the Horne Creek fault to the south, is interpreted to be a cauldron approximately 20 km in diameter. Its western and eastern boundaries are the Flavrian Plutonand the D'Alembert shear zone respectively. The complex has an exposed stratigraphic thickness of 10.5 km. Two cycles, composed of andesitic units overlain by bimodal, andesite - rhyolite units, are observed in the area, and are, in turn, overlain by an andesitic unit interpreted to be the lower part of a third cycle.The southern sector of the Blake River Group, south of the central volcanic complex, is considered to be outside the limits of the cauldron, but partly contemporaneous with it. The maximum stratigraphic thickness exposed in this area is 4 .6 km. At least two cycles occur in this sector. The oldest unit, a pre-cauldron andesitic to basaltic unit, occurs only in the southern part of the sector. In the north, two partial andesite - bimodal cycles, interpreted as contemporaneous with the cauldron volcanism, are observed.The eastern sector of the Blake River Group, east of the central volcanic complex, apparently overlies the complex. Two units are observed in this sector: a lower bimodal unit and an uper andesitic unit. The bimodal unit is coupled with the uppermost andesitic unit of the central volcanic complex to form a cycle, and the andesitic unit is considered to be the uppermost unit of the Blake River Group. The total exposed stratigraphic thickness in the sector is 2.5 km.The western sector of the Blake River Group, north and west of the central volcanic complex, is interpreted as the lateral equivalent of the complex. Three andesite - bimodal cycles are exposed in this sector, giving a total stratigraphic thickness of9 .5 km. The two lower cycles correspond directly to the central volcanic complex cycles; this correlation is facilitated by two stratigraphic marker units observed on either side of the Hunter Creek fault: the Fish-roe rhyolite flow, east of the Flavrian pluton, and a spherulitic rhyolite lapilli-tuff, west of the Flavrian pluton.Many of the volcanogenic massive sulphide deposits found in the central volcanic complex are spatially and temporally associated with synvolcanic faults, and felsic domes and feeder dykes that are the sites of felsic volcanism in the bimodal units. However, these features also occur outside the central volcanic complex, and the similarities recognized in this work between the complex and the surrounding area suggest that such deposits need not be restricted to the central volcanic complex. The presence of volcanogenic massive sulphide deposits outside the complex confirms this."

Jan 1, 1990

By R. M. Young

In. East Kootenay, two Companies are operating, the Crow's Nest Pass Coal Company of Fernie, with mines at Coal Creek and Michel, and the Corbin Coal and Coke Company, of Corbin and Spokane. Wash., with mines at Corbin. The Crow's Nest Pass Coal Company has also coke-ovens of the bee-hive type at Fernie and Michel. The mines have a productive capacity, with present development and plant, of approximately 1,500,000 tons of coal, and of 300,000 tons of coke annually. The total production in 1923 was 828, 990 tons of coal and 65.990 tons of coke. In the early years of operation, the mines furnished a very large percentage of their output to the railways and smelters. These were, in fact, the primary markets for which the mines were opened and the ovens constructed. The Great Northern Railway had built into Femie, and later extending its line to Michel, became a heavy consumer of both of these mines. The Spokane International, connecting the Crow's Nest branch of the C.P .R. with Spokane, furnished tonnage to Corbin. The Canadian Pacific Railway bought for Crow's Nest consumption. The smelters at Grand Forks and Trail in the Boundary country were large and steady consumers of coke, while in-termittently Northport, Butte, Helena, and Great Falls shared in the product of the ovens.

Jan 1, 1924

By R. O. Suzuki, S. Natsui, R. Nashimoto, T. Kumagai, T. Kikuchi, H. Takai

A newly developed computational fluid dynamics model based on a multi-phase particle simulation is presented for predicting the entrainment behavior of liquid metal into slag due to rising single bubble. By comparing results calculated using this model against experimental data, it was found that the transient behavior of bubbles and the two immiscible liquids can be accurately estimated by this method. The rupturing of the thin water film surrounding the bubble was less reliably predicted, but this 3-dimensional unsteady numerical model still nevertheless provides valuable new information for directly predicting the change in the liquid-liquid interface over time. This model predicted the Young-Laplace pressure, and the interface shape was simulated with volume conservation using this model as opposed to the conventional particle method. This simulation model can calculate both of dispersed phase and continuous phase seamlessly.

Jan 1, 2015

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By Hans Chr Andersen

Almost every form of iron ore and carbon material has been used as a raw material in the production of pig iron in electric reduction furnaces. Experience derived from the operation of the large 33,000-kva. Tysland-Hole furnaces, however, indicates that production results are very much influenced by the raw material conditions. The author presents the principle pattern of the metallurgical structure of the interior of an electric pig iron furnace. On the basis of this, he discusses the variations of electrical and metallurgical conditions for the process which will take place with changing raw materials. The formation of a coke bed underneath the electrodes, and its influence on the furnace operation, is illustrated. Quality and grain size of the coke added to the charge will influence the build-up of the coke bed and will thereby also affect the electrical re-''Elektrokemisk A/S, Oslo, Norway. resistance and reduction potential in the furnace.

Jan 1, 1963