Search Documents

By Leroy C. Stewart

Owing mainly to the use of ethylene dibromide in the production of tetraethyl lead for gasoline treatment, there has been a tremendous increase during the past decade in the demand for bromine. In the United States, production, derived mainly as a by-product from the treatment of brines from salt wells, rose steadily from about two million pounds in 1924 to nine million pounds in 1931. In 1936, production amounted to between 20 and 21 million pounds. Much of the increase during the past four or five years has been due to the operation of the Ethyl-Dow Chemical Company's plant, which extracts bromine directly from sea water. The process employed by the Ethyl-Dow Company is somewhat similar to that in use on salt-well brines at their plant at Midland, Michigan, but whereas these brines contain around 1,300 parts per million bromine, sea water contains only 65 to 70 p.p.m.-about as much as the waste effluent in the brine process. By intensive research, however, a process was developed whereby a very considerable percentage of the bromine content of sea water could be recovered, and at a satisfactory operating cost. In its essentials, the process consists in liberating the bromine from the sea water by treat-ment with chlorine, blowing the bromine out of the water by a current of air, and finally absorbing it in a solution of soda-ash.

Jan 1, 1938

By John E. Udd, Peter Leinberger, Roman Kozarycz

"This paper is based on work done by the authors in a study of the structural features at a quarry excavated in Chazy limestone on the Island of Montreal. Observations on failures on the quarry walls and benches were recorded, and back analyses of small-scale failures were carried out, thus enabling an assessment to be made of the in-situ strength properties of the rock. Using this information, and data from shear tests in the laboratory, the authors made an analysis of the stability of the south wall of the quarry.IntroductionQuarrying, and excavating for foundations, in the Montreal area involves the removal of million s of tonnes of rock on an annual basis. Even when compared with the quantities mined at major open-pit mining operations, the production figures are impressive. At present, for example, crushed stone is produced at almost 20 quarrying operations either on, or near, the Island of Montreal. The annual capacities of the larger quarries are in excess of one million tonnes each. Lesser, but still substantial, production is achieved at the smaller quarries.Excavations, for foundations , especially during periods of peak construction activity, must also involve large quantities of rock . The writers, however , are not able to produce an estimate of the actual annual tonnages originating from excavations."

Jan 1, 1981

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By F. Baerhold

Recycling of hydrochloric acid from the pickling of mild steel using pyrohydrolysis is a state-of-the-art technology. Recent developments have focused on the production of a high value iron oxide by-product, where the chemical purity and physical properties are the main issues. New processing routes, especially for TiO2 and Ni production, use leaching operations with hydrochloric acid. The feasibility of those processes depends on the availability of an economic and reliable process for the recovery of the acid. Depending on the level and type of impurities and the required specification of the by-product, pyrohydrolysis in a fluid bed or in a spray roast reactor can be the ideal solution. In stainless steel annealing and pickling lines, a mixture of nitric and hydrofluoric acids is used to remove the scale from the surface after heat treatment. Nitrate emissions from the pickling and the rinsing processes have to be avoided because of more stringent environmental regulations. An annealing and pickling line that is totally wastewater-free was developed, where not only the nitric/hydrofluoric acid but also the rinse water, is completely recycled. New developments to increase the HNO3-recovery rate and to obtain a metal oxide by-product that is easier to recycle are presented.

Jan 1, 2006

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By R. D. Brown

"An adequate level of R & 0 is crucial to achieve gains in productivity and to strengthen Canada' s position in an increasingly competitive world ." So stated Finance Minister Jean Chretien in his April 10, 1978 budget speech, on announcing a new measure designed to increase the productivity of Canadian industry and to assist in the creation of new technology. The effect of the new measure, which permits an income tax deduction of 150% of certain research and development (R & D ) expenditures , can reduce the after-tax cost of a marginal dollar 's worth of such expenditures to as little as 20 cents . This article discusses the income tax treatment of R& D expenditures in general, and describes in particular the income tax incentives which relate to R& D.

Jan 1, 1978

By W H. Poole, E. R. W. Neale

A new style of tectonic map based on age of folding has been prepared for the Canadian Appalachian region as part of the Tectonic Map of Canada Project. This style of map pro-vides a clearer picture of the tectonic history of the region than any meth-od hitherto attempted. Precambrian blocks that were relatively unaffected by Palaeozoic de-formation are distinguished on the Great Northern Peninsula and in the Conception Bay region of Newfound-land. K/ A age determinations suggest that these blocks were intruded and metamorphosed during Grenville orogeny. Other Grenville-like rocks, on Cape Breton Island and in New Brunswick, were more actively involved in subsequent Palaeozoic orogeny. Taconic orogeny, the first phase of Palaeozoic deformation, took place in Middle and/or Late Ordovician time and was accompanied by intrusion of ultrabasic rocks. Evidence of the -

Jan 1, 1961

By A. W. Davis

Sapping and mining have constituted an important part of siege operations ever since powder came into general use in Europe. Before this period, famine was the main weapon in the hands of the besiegers, and the history of the middle ages is replete with accounts of sieges lasting two and three years. With the advent of explosives, a position impregnable to assault might be readily won by mining under, and blowing up, its defences. The natural offensive against this method of attack is to countermine and stop the attackers underground before their objective is reached. Thus developed the art of military mining. The French and British, in the Peninsular war, were adepts at this method of warfare, and the explosion of a mine and the formation of a breach were the usual preludes to the general assault of a position. In the Crimea, at Sebastopol, the British and Russians did a lot of underground fighting, as the old maps of their galleries, now in the museum at Chatham, will testify. In the siege of Port Arthur, in still later times, the Japanese and Russians were hard at it as well.

Jan 1, 1926

By T. C. Murphy, W. Taciuk

In 1966, the Iron Ore Company of Canada commissioned a wet magnetic scavanging plant for the recovery of fine magnetite values p.resent in spiral tailings discharged from a spiral gravity separation process. The plant includes dewatering, grinding, classification, thickening, mini-wedge screening, and primary, secondary and tertiary wet magnetic separation stages. The source of feed varies in quantity and quality, so the original design included variable operational procedures to deal with these conditions.

Jan 1, 1972

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016

By C. D. Anderson, C. G. Anderson, P. R. Taylor

"Rare Earths have become critical for our energy and materials driven society. While primary production must ramp up to fill growing demands, the recycle of these strategic elements must also be initiated. This paper will outline the potentials of and metallurgical technologies employed for Rare Earths recycle from various secondary sources.INTRODUCTIONWhen investigating the recovery of rare earths from secondary sources it is necessary to understand the nature of the sources to be processed. As of 2009, the USGS reports the distribution of rare earths by end use, in decreasing order, was: chemical catalysts 22%, metallurgical applications and alloys 21%, petroleum refining catalysts 14%, automotive catalytic converters 13%, glass polishing and ceramics 9%, rare earth phosphors for computer monitors, lighting, televisions 8%, permanent magnets 7%, electronics 3%, and others 3% (USGS, 2011). Additionally, it is reported that the amount of recycling was quite small and consisted primarily of rare earth magnet scrap, although with the sharp increase in the price of rare earths, and the potential shortage in supply, focus in this area is continually growing. Thus, the opportunities, whether realistic or not, are extremely vast in the recycling of rare earth containing materials. The following subsections will present methods proposed for the recycling of rare earths based on the feed material type.RECYCLING OF RARE EARTH MAGNETSCurrently, investigations are ongoing in the area of recycling production scrap and end-of-life materials in the rare earth magnet industry. The following techniques illustrate potential methods for the recovery of rare earths from secondary RE magnet sources.Recycling of Rare Earth Magnet Sludge by Selective ChlorinationDuring the production of neodymium magnets, a by-product of production is the so called “magnetic sludge”. This by-product contains high amounts of neodymium, thus a process for the recovery of Nd has been proposed. In this process the Nd present is selectively chlorinated/distilled by the addition FeCl2 via the following reactions."

Jan 1, 2012

Accurate hematite solubility data are required to construct predictive solution chemistry models for complex hydrometallurgical solutions. These data are useful in understanding Fe(III) speciation and precipitation in a variety of hydrometallurgical processes. Hematite solubility data were generated in 10 to 70 g/L H2SO4 solutions and at temperatures from 130 to 270°C, using specially modified titanium autoclaves. These measurements represent an improvement over previous experimental data because of better in-situ filtration of the sample aliquots, the approach to equilibrium via hematite dissolution, and the inhibition of Fe(III) reduction on titanium surfaces. Fe(III) reduction was particularly studied to evaluate the inflationary effect of Fe(II) on hematite solubility measurements. Chromate was found to reliably inhibit Fe(III) reduction on titanium. Finally, the generated hematite solubility data were used to construct a solution chemistry model using the OLI software.

Jan 1, 2006

By J E. McMynn

The development of the Granduc mine presents a number of problems which are peculiar to its location and surrounding terrain. Because the development tunnels portal onto an area which is covered by an extensive glacier, and the mountain-side is subjected to dangerous snow slides, it was decided to construct an underground powerhouse to supply the necessary electric power and compressed air. This paper deals with the special problems inherent in the design and -construction of an underground plant. It involves the installation of diesel-electric generating equipment having an aggregate capacity of 1,050 kw.,and of air compressors with a total capacity of 2,400 cfm. Items dis-cussed include the selection of equipment to meet site conditions, the ventilation and cooling of the underground room, and the protection of personnel and equipment from explosions and fire. A short discussion on the automatic supervisory and alarm installation is also included. THE Granduc mine is located 135 miles north of Prince Rupert and 25 miles north of Stew-art. This seems quite accessible, mileage-wise, but, due to mountains,

Jan 1, 1963

By J. B. Evans

"NORMALLY the duties of the exploration engineer and geologist cover the initial, and possibly, the most important phase of mining property evaluation; that phase being the presentation of an opinion of the property's ore reserve potential in terms of tonnage and grade. The prime objective of this pa-per is to outline one method of bridging the wide gap that lies between a know ledge of a property' s tonnage and grade potential and an appreciation of the value of that property in dollars and cents.THE PRESENTATION OF PROPERTY EVALUATIONThe engineer engaged on a mining property evaluation, regardless of whether he be an independent consultant, or a company employee, has as his goal, the presentation of his appreciation of the property's potential value or worth within terms of reference acceptable to his principal.To furnish a complete evaluation report, the evaluator must firstly study all aspects pertaining to the particular property under consideration, then present his appreciation of the property's worth in some tangible form. The ultimate presentation is one giving a Present Value of the pro pert y in terms of monetary exchange. Such an idealistic presentation is not always possible; typical preventives being -insufficient reliable information, limited time, Jack of ability and absence of definite direction."

Jan 1, 1960

By Denis Yaychuk, Gary Billingsley

The economic eva luation of a mineral property or mining venture should include the quantification of ri k as part of the analy is. The re ults of such an analysis provide the decision-makers not only with the most likely financial outcome and the probability of achieving that or any other outcome. but al o with a ranki ng of the relative impact of all the ri sk factors. These type of resu lts offer more complete information for investment and technical deci ions than the traditional cash flow/ ensitivity analysis. In addi tion. by attempting to quantify ri sk. the personnel providing the va ri able input are forced to take a much clo e r look at the data involved, and are fo rced to work together. the reby increa ing substantially the awa reness of the impact their work and others· work has on th e outcome of the analysis.

Jan 1, 1986

By Alfred Guenkel, Kyle Marte, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985 (Borbely, Devuyst, Ettel, Mosoiu & Schitka, 1985). Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. Though it is possible to supply sulphur dioxide (SO2) in either gas or liquid form, the majority of these SO2/air operations use sulphite-based salts as the ‘SO2’ equivalent reducing agent. This is probably due to the lower capital cost, safety concerns with, and availability of liquid SO2. Sodium metabisulphite (SMBS) is commonly employed, and its cost is an order of magnitude higher than that of sulphur. The increased capital expenditures (CAPEX) for a sulphur-burning SO2 gas plant could have a pay-back of less than two years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas inventory. Furthermore, a SO2 gas plant will not trigger the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and Boleo).This paper discusses the different processes which require SO2 as a reducing agent and compares the capital and operational costs of a SO2 gas plant to conventional process alternatives using sulphite-based salts or liquid SO2.The heart of the SO2 gas plant is the sulphur furnace. The most economical way to produce SO2 is by combustion of sulphur in air producing up to 19.5 vol% SO2. Examples of large and small sulphur furnaces are discussed in terms of design, operation, and impacts on operational costs.The SO2 gas produced in a sulphur-burning plant has to be contacted with the liquor to be reduced. The choice of gas-liquid contacting device is important, and two contacting devices are discussed: 1) Gas sparging into the bottom of leach tanks (high, nearly constant, back pressure due to liquid head) and 2) absorption columns (low gas-side pressure drop)."

Jan 1, 2014

By A. C. Hnatyshyn

INTRODUCTION THOSE concerned with coal mining operations in Alberta have been asked repeatedly the same question, "Why is mechanization in Alberta proceeding so slowly as to lag far behind the mines in the United States?" This question is often asked in such a manner as to indicate that a severe reprimand is overdue to the mining engineers of this Province for their apparent indifference to the problem of improving their mining operations by increased mechanization. To the average person, unacquainted with mining conditions and problems, mechanization appears to be simply a matter of introducing equipment to load coal underground and, once this is done, substantial economies in operating costs will automatically follow. Invariably, those who have followed this simple reasoning have found, to their regret, that such is not the case and that effective mechanization involves something more than the mere process of introducing loading equipment into a mine. To be effective, any programme of mechanization must take into consideration all operations incidental to the mining, transportation, and handling of the coal from the working face to the tipple, and must utilize equipment which can be best adapted to any peculiar condition or circumstance prevailing in the mine concerned. In the use of such equipment, the net and final result should be an improvement in operating costs of sufficient magnitude to at least return to the operator, over a specific period of years or during the expected life of that equipment, all his investment plus a fair return on that investment.

Jan 1, 1951

By A. M. L. Cushing, S. Kelebek

Presently, adsorption is one of the effective methods of removing toxic contaminants from waste waters. The contaminants from metal mining industrial operations include an effluent water containing various types of heavy metal species at concentrations beyond the maximum allowable limits, which are 0.5 ppm and 0.3 ppm for nickel and copper species, respectively. Adsorption behavior of copper ions pre-chelated with diethylenetriamine (DETA) and triethylenetetramine (TETA) onto natural bentonite and peat has been investigated. Both natural bentonite and peat was found to be capable of removing these copper-polyamine complexes from aqueous solutions relevant to process water effluents. However, the adsorption capacity of bentonite was significantly higher than that of peat. Two models were used to study the adsorption kinetics: a pseudo-first-order rate expression and a pseudo-second-order rate expression. For both adsorbents, the data conformed best to the pseudo-second-order rate expression. Representation of the experimental data through adsorption models was also investigated. Out of the four cases considered, namely, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms, it was found that for both bentonite and peat, the copper polyamine adsorption data conformed best to the Dubinin-Radushkevich adsorption model. The Langmuir model also represents the bentonite-copper polyamine adsorption system reasonably well as the second best case, suggesting that the amount adsorbed on bentonite might be a monolayer with strong affinity.

Jan 1, 2015

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970