Search Documents

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

By D. M. Slavich

"In today's operating and investment climate, project evaluation is both more important and more difficult. It is more important because economic and financial analyses of a proposed project provide a basis for judgment of a project's commercial viability by equity participants, lenders and, in some cases, other participants such as off takers and governments. It is more difficult because these analyses must, of necessity, be based on estimates, projections and evaluations which must be made in a period remarkable for its economic and political uncertainty.Project evaluation starts with the analysis of the engineering, commercial and financial information available. Beginning with the preliminary design and capital cost estimates, alternative financing plans can be developed outlining possible sources of funds, terms and security arrangements. Pro-forma financial statements can also be developed, including sources and uses of funds, cash flow schedules, income statements and balance sheets. With these results, various profitability measures can be determined.Subsequently, in an effort to deal with uncertainty, these results can be tested by measuring the impact on project viability and profitability of changes in project and external variables such as product process, mining and processing rates, operating and financing costs, currency exchange rates and other factors.The results are a number of financial projections reflecting different assumptions for key project parameters. The projections can be used to structure the project to achieve the maximum financial performance. Projects, the financial viability and profitability of which can be demonstrated under varying market conditions, will be the most competitive in capital markets."

Jan 1, 1982

By L. R. Bower

"This paper describes a highly versatile variable speed unit with a torque multiplication feature as a direct replacement for a fluid coupling .The unit is comprised of a modulating clutch with torque converter and lock-up options.The UCD does not start or stop the motor. This is carried out in the normal manner.The UCD continually monitors and rapidly regulates the output speed to the requirement of a set point demand from input signals or a pre-set program with full manual override.The pre-set program can include start and stop ramps, top speed and minimum speed regulation and also mid-speed set point with security for man-riding, etc. Speed variation is from zero to 100% on a constant duty basis.The input signals can be from any source, e.g. belt weigher. load profile bunker probes, mine monitoring system, etc.The UCD when fitted with a torque converter has a torque multiplication feature which automatically provides a starting torque up to two and a half times greater than the full load torque without exceeding the normal motor power levels.IntroductionIt is common practice in the mining industry to drive conveyors, whether they be belt or chain, through a transmission system incorporating a fluid coupling between the driving motor and gear-box .However, there are drawbacks and in an effort to attain a better degree of drive and control, two-speed motors - inverters cycle- converters - hydrostatic drives, etc ., have been introduced."

Jan 1, 1986

By J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

"Ni-based superalloys have been replaced in the last low pressure stage of jet turbines for aircraft by titanium aluminides. In order to improve the properties of these Ti-Al alloys and extend their usage deeper into aircraft engines grain refinement by inoculation has been investigated. Borides are the most common inoculants for Ti-Al alloys, however they form brittle particles which are detrimental to the final properties of the alloy. Inoculants manufactured from a Ti-Al alloy with refractory metal additions were proposed to alleviate the issues arising from inoculation with brittle particles. An alloy was chosen which had less than 10% lattice mismatch with the alloy of interest (Ti-46Al) to maximize efficiency. Initial experimentation showed a decrease in as-cast grain size by a factor of 2 between the inoculated and non-inoculated samples along with an absence of the brittle particles found with boron inoculations. Investigations into the interaction between the inoculants and the melt were also carried out to better understand the inoculant size distribution and efficiency upon solidification.INTRODUCTIONTitanium aluminum alloys are an interesting material for aerospace applications. Their high temperature oxidation resistance and high specific strength make them particularly promising (Kim & Dimiduk, 1991). Recently, titanium aluminides have replaced nickel based superalloys in the last low pressure stage of the GEnx turbine engine. In order to increase their usefulness in turbines their properties must be improved for high temperature (>800oC) applications. Grain refinement is one method to improve the properties of a material, however current methods of grain refinement of Ti-Al alloys by inoculation have significant drawbacks. A new method of inoculating Ti-Al alloys by using Ti-Al alloys with small refractory metal additions (Nb, Ta) has been developed to avoid the drawbacks of current methods while still being effective grain refiners."

Jan 1, 2016

By A. Holland, T. Krumins, E. Olin, J. F. M. Castilleja, J. Geldart, C. Fleming, I. Jackman

A flowsheet has been developed to treat the flotation tailings from a copper mine in Mexico to recover gold and silver by cyanidation and carbon-in-pulp (CIP). The plant will treat ~15,000 t/day of a 60:40 blend of current flotation tailings and the mine’s historic tailings. The tailings also contain a significant amount of cyanide-soluble copper, and the economic viability of the project is strengthened by recovering most of the copper and cyanide associated with this process. The solution and solid phases in the CIP tailings will be separated in a counter current decantation (CCD) circuit and the CCD solution overflow will be treated by a SART Process. Copper precipitates as a salable copper sulphide product in the SART Process and the cyanide that is associated with the copper complex is regenerated as free cyanide. After SART, a portion of the SART product solution will be recycled to leach to reuse the free cyanide, while the remaining solution will be used as wash water in the CCD circuit. Incorporation of the SART Process in the flowsheet allows the CIP circuit to be operated aggressively as a gold plant, which means most of the silver in solution passes through CIP to SART. Silver co-precipitates with copper in SART and is recovered very efficiently with the copper sulphide by-product. Incorporation of SART also allows the leach and CIP circuits to be operated with relatively high levels of free cyanide, which enhances silver leach kinetics and helps keep copper from loading onto the carbon in CIP. The flowsheet was developed in the laboratory and successfully demonstrated in a fully-integrated pilot plant in 2018.

Jan 1, 2019

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By A. B. Parsons, P. G. Howes

"This article discusses how recent changes in the federal and Quebec .income tax laws have contributed to an improved investment climate for mineral exploration in the Province of Quebec. Individual investors who are resident in Quebec and who are in the highest tax bracket (1984-60.4% marginal rate) may obtain tax benefits that result in only nine cents of each invested dollar being at risk.IntroductionIn a recent submission by the Mining Association of Canada to the Royal Commission on the Economic Union, it was stated that the mining industry ""is no longer discovering and opening new mines at rates sufficient to offset the depletion of existing orebodies and to maintain pre sent output"". With world metal prices still in a depressed state following the prolonged 1981-82 recession, moreover, the continuing success of Canadian mining in world markets will depend on this country's ability to compete in a new environment characterized by subsidized Third World production . For the most part, this new competitive environment will encourage the development of cost-efficient mines that are better equipped to withstand the troughs and valleys of international metals prices."

Jan 1, 1984

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

By Arsalan Talebzadeh

Construction -Surface ?First two intake fans constructed in 2007; third fan added in 2008 to reduce resistance in the system. 450 HP fans. ?Excavation for exhaust fans started in 2008. ?In parallel with underground construction in preparation for the changeover. ?Bulkhead in place prior to completion/ commissioning of

Oct 1, 2010

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By John B. Hodgeson

AMMONIA is an essential constituent in the production of the ammonium-sulphate and ammonium-phosohate soil fertilizers manufactured by the Consolidated Mining and Smelting Company of Canada, Limited. The fertilizer plant, built in 1930 at Warfield, near Trail, provides a means of utilizing the large amount of sulphuric acid produced from the sulphur dioxide which is removed from the smelter smoke. The plant has an avail-able source of cheap power which makes the production of fertilizer economically possible. The fundamental operations involved in the production of ammonia at the Warfield plant are, first, the manufacture of hydrogen by the electrolytic dissociation of water; next, the recovery of nitrogen by the fractional distillation of liquid air; and finally, the combination of hydrogen and nitrogen in proper proportions and under suitable conditions to form ammonia.

Jan 1, 1938

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966