Search Documents

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By R. E. Dye

Introduction Research concerning all phases of hoisting practice, but more particularly the causes and prevention of hoisting rope deterioration and the improvement of safety dogs 158 for shaft conveyances, has been carried on intensively for the past three years in the Province of Ontario. Prior to the hoisting accident at the Paymaster mine on February 2nd, 1945, there had been no fatalities in the Province due to a hoisting rope failure. It was probably on this account that little original research on hoisting problems had been undertaken here and that the mining industry had been content to look to British, South African, and United States investigators for new developments in this field. Except for the Paymaster accident this might still be the case since, in any industry, it is apparently necessary for a serious accident to occur before any extensive programme of preventive research is launched. When this accident occurred, the Government of Ontario, with the close co-operation of the Paymaster officials and the mining industry as a whole, took immediate steps to determine the cause. A five-man, non-industry committee, selected from the Faculty of the University of Toronto with Dean C. R. Young as Chairman, was appointed by the Government, and a three-man Committee consisting of R. D. Parker, General Superintendent of the International Nickel Company of Canada, Limited, R. L. Healy, General Manager of Wright Hargreaves Mines, Limited, and R. E. Dye, General Manager of Dome Mines, Limited, with the latter acting as Chairman, was appointed by the Ontario Mining Association.

Jan 1, 1948

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By Arun Verma

Thermal energy storage offers a means of effecting significant costs savings and conservation of premium fuels. Na2SO4 has been found to be a good material for storing thermal energy in the medium-temperature range, mainly because of its dimorphic nature and high heat of transition. Basic data and development of the salt to a practically usable block are discussed.

Jan 1, 1978

By Ronald E. Pike

"PREFACEAt the CIM Annual General Meeting in Quebec City, R.E. Pike of The Toronto-Dominion Bank described how the Canadian banking industry worked with the minerals industry to assemble the large capital requirements for resource projects in Canada and overseas. He developed a profile of the mining industry and Canadian banking, both being important sectors of the Canadian economy and global in context. He also outlined the banking and financing partnership that existed in the past. In looking to the future and challenge that lies ahead f or each industry, Mr. Pike questioned whether the financing practices of the 1970s will be acceptable over the next decade. In that regard, he highlighted the risks that impact on each industry and illustrated how that financing partnership might evolve in response to those forces. The folio wing is a synopsis of his paper.IntroductionThe Canadian mining and metals industry is prominent in the domestic economy and respected internationally. Any measure of its performance illustrates that status-percentage of GNP, employment, exports, capital investment, size relative to other producing nations, etc.Energy, Mines and Resources Canada has forecast that the non-fuel minerals industry will grow in real terms by an average annual rate of 3.0% over the period 1981 to 1991. Using the GNP as reference, that growth in non-fuel mineral production will represent 7.7% of GNP. In translating that growth to capital expenditure, the EMR Canada estimates the aggregate amount at $43.8 billion ('79 dollars) or approximately 12% of total business investment in Canada during the 10-year period.About half of the $43.8 billion will be devoted to the ferrous sector-$8.4 billion in iron ore mining and $12.4 billion in the steel industry. Capital investment in nonferrous s projects is estimated at $13.3 billion, and it is projected at $6.7 billion for industrial minerals. The residual $3.0 .billion is exploration spending."

Jan 1, 1982

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By Xueyuan Nie, Xuezhi Zhang, Henry Hu, Shen Xinwei, Jimi Tjong, Li Fang

With the demand for weight reduction in vehicles and airplanes, researchers have shown great interested in casting wrought aluminum alloy 7075 because of its potential advantages such as high strength-to-density ratio and stress-reduction capabilities. It is therefore essential to conduct a fundamental investigation on solidification behavior and grain microstructure of alloy 7075. In this study, a commercially-available wrought aluminum alloy 7075 was used to study the solidification behavior of alloy 7075. A thermal analysis was performed based on the cooling curve and its corresponding first and second derivative curves. The nucleation of the primary a-Al phase and eutectic phases were analyzed. The comparison between the microstructures of the wrought and cast 7075 alloys shows that coarse microstructure and porosity are present in the cast alloy. The techniques for grain refinement in casting, such as the addition of the nucleating particles and applied pressure, should be employed to reduce the dendrite arm spacing and the porosity.

Jan 1, 2015

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Mineral Exploration Best Practice Guidelines (the Exploration Guidelines) have been prepared to assist professional geoscientists and engineers to conduct consistently high-quality work in order to maintain public confidence. The Exploration Guidelines are meant to assist professional geoscientists and exploration practitioners in planning, supervising, and executing exploration programs. In Canada, there are generally two types of public resource reporting: “Disclosure”, as defined by NI 43-101, is the reporting of technical information to the public and market participants for securities legislation purposes where a Qualified Person (QP) must be involved, and reporting of exploration information for governmental agencies to support obligations under laws including the Mining Acts of each of the Provinces and Territories. The Exploration Guidelines are also relevant where the results will not be publicly reported but are intended for internal company use. While this document is intended as guidance for work conducted or supervised by geoscientists in Canada, many of the practices described herein can be adapted to mineral exploration activities in other countries. The Exploration Guidelines are not intended to inhibit original thinking, or to prevent the application of new approaches that may develop into fundamental components of successful mineral exploration programs. Rather than provide prescriptive solutions to specific issues, they include general guidelines for current professional practice and to demonstrate and defend the merits of new methods. These guidelines do not preclude individuals and companies from developing more detailed guidelines specific to their own requirements. The initial version of the Exploration Guidelines was prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) Exploration Best Practices Committee and adopted by CIM Council on August 20, 2000. On January 9, 2018, CIM Council formed a new committee, the Mineral Resources and Reserves Committee (CIM MRMR Committee) with a mandate to, among other things, update the Exploration Best Practice Guidelines. The mandate for the committee was accepted by CIM Council on March 2, 2018. The new document was adopted by the CIM Council on November 23, 2018.

Nov 23, 2018

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013

By W. McCombe, G. Remple, L. Nightingale-Mercer

The McClean Lake Mill is located approximately 850 kilometres north of Saskatoon, Saskatchewan, Canada, and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and a multi-year expansion was completed in 2014 to increase its production capacity to 24 Mlbs U3O8 per annum. The mill also underwent various upgrades to allow it to safely transition from processing low grade ores to high grade ores from the nearby Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones of the deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk posed by hydrogen gas. During 2013 Orano and its consultant Hatch designed and engineered several novel upgrades to the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit could be safely operated with ores that evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project, and also provides an update on the operational reality of hydrogen in the circuit gained through five years of operational experience with hydrogen evolving ores.

Jan 1, 2020

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By W. E. Roscoe

The probability of making an exploration discovery in Canada can be calculated from Derry's (1970) data on exploration expenditures and number of discoveries over the last nineteen years. Considering an average exploration "try" to be $30,000, the probability of a discovery with one try has decreased tenfold from about 0.01 in 1951 to 0.001 in 1969. A plot of these probabilities can be extrapolated to the future, giving a 1969-71 three-year average probability of 0.00096 with 90 per cent confidence limits of 0.00042 and 0.00153. Using this probability, various calculations can be made, such as (1) the probability of making at least one discovery for any given exploration expenditure, (2) the probability of ultimate ruin or survival of the exploration investment process and (3) the expected value of an exploration investment. There is a critical minimum amount per discovery that must be re-invested in exploration, no matter how large the original investment is, for exploration to survive at all in the long run. Currently, this critical minimum is $31,200,000 with 90 per cent confidence limits of $19,600,000 and $71,400,000.

Jan 1, 1971

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By George S. Martin, Michael D. Winship

"Placer Dome Inc. is the operator of the Musselwhite project located 100km north of Pickle Lake, Ontario. J.S. Redpath Limited was contracted to conduct an underground exploration program using shaft access.During the winter of1988, the shaft collar was established in 16 metres of water bearing sand and till overburden. This paper will illustrates the engineering techniques used to overcome the obstacles to installing a shaft collar in deep overburden. Specialized dewatering and piling procedures were employed.INTRODUCTIONHarold and Allan Musselwhite discovered gold in the Opapimiskan Lake area, north of Pickle Lake, in 1962. The prospectors were grubstaked by ten companies in 1973.A diamond drill program was initiated shortly thereafter.In 1983an underground ramp exploration program was carried out on the West Anticline portion of the property. The program was unsuccessful in establishing an ore reserve so surface exploration continued. In 1986the ""T"" zone was discovered. Further surface drilling was done and an over-all drill-indicated reserve of 6 million tonnes at 7 grams per tonne was outlined. The gold mineralization occurs in several vertical tabular deposits within the iron formation. In late 1987the joint venture partnership, now consisting of Placer Dome Inc., Inco Gold Co., Corona Corporation and Esso Minerals Canada, contracted J.S. Redpath Limited to conduct an underground exploration program on the ""T"" Zone.The scope of work for the project was to: 1. establish a 45 km winter road in 1988 and 1989;"

Jan 1, 1989

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American?s suite of specifications for gearless mill drives (?GMDs?). These specifications are based on experiences in both Anglo American?s and others? operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

The Industrial Minerals Milling Section of the Mineral Processing Division has been engaged for the past three years in a study of the separation of minerals, by means of electronic sorting equipment, on the basis of their colour. Considerable knowledge of the subject has been built up. Because the object of this study is application as a means of beneficiation, a number of examples of the separations achieved are presented. Introduction T 0 the mineral collector, the colour of a mineral may be pleasing, even fascinating; to the mineralogist, student or professional, it may also be practical. It serves, to some extent, as a distinguishing feature in many minerals, and helps to fix with reasonable accuracy the identity of a few. It may now become a useful tool of the mineral dresser. The idea of using a difference in colour as a means of separation of one mineral from another is not new. Hand sorting dates back to ancient time. However, the means by which this can be done mechanically was developed only during the past decade. As far as the Mineral Processing Division is concerned, interest dates from March, 1960, when the following item was observed in the

Jan 1, 1965

By S. B. V. Stewart, W. W. Forsyth

"Since the Mathew's method for open stope design was first proposed by Golder Associates in 1980 it has been applied at a number of mine sites in Canada. The initial hypothesis was based on a relatively small amount of data and the intervening period has allowed the collection of a significant amount of new data to test the validity of the method.This paper examines a brief history of the evolution of rock mass classification systems to provide background and emphasize their empirical and non-rigorous approach. It also presents the new data which appear to indicate that the initial hypothesis was reasonably good. The modification to the original graph proposed by Potvin is discussed as well as the applicability of the method to predicting the onset of caving. The original graph has been updated and has been subdivided into four zones described as ""stable""; ""potentially unstable""; ""potential major failure""; and ""potential caving"". The method is recommended as a useful open stoping design tool provided it is recognized that it is not a rigorous design method.Finally the paper proposes a recommended approach for application of the method by would-be users and addresses some typical pitfalls that may be encountered."

Jan 1, 1995