Search Documents

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By P. Scinto, P. Hudson

"Modern day ore bodies are becoming increasingly harder, more abrasive and lower grade. The Mako deposit is located in Senegal and consists predominantly of primary mafic and felsic lithology that are both very competent and very abrasive ores (Axb < 30, BWi >20 and Ai >1.0). The deposit was initially discovery in 2010 and the Toro Gold management team fast tracked the Mako Project through development and into production to achieve its first gold pour in January 2018. The comminution circuit comprises primary crushing single stage SAG milling with recycle crusher (1oCR SS-SAC). The mill reached design throughput and grind size seven weeks after first ore. The Mako project marks another successful international application of single stage milling, which represents a simple and easy to operate comminution circuit for small-to-mid size projects with a low capital cost. This paper describes the ore interpretation, comminution modelling, grinding circuit selection and design, as well as an overview of the commissioning and ramp-up of the mill.INTRODUCTION The Mako Gold Project is operated by Toro Gold Ltd., which holds a 90% interest in the project. The project is located in south-eastern Senegal in the Kedougou region, close to the Gambia river and township of Mako. The Mako deposit lies in the “Kenieba Window” of eastern Senegal and western Mali, which hosts a number of gold mining operations and development projects. The Mako Gold Project has an estimated life of 8 years with overall recoverable gold estimated at 924 koz. The process plant is designed to treat 1.8Mt/a of ore and produce 128 – 143 koz of gold per annum. Lycopodium Minerals Pty Ltd (Lycopodium) was appointed to provide feasibility studies and EPCM services for the greenfield project. Forming part of consultancy services provided by Lycopodium, Orway Mineral Consultants (OMC), a subsidiary of Lycopodium, was involved in the design, commissioning, ramp up and ongoing post commissioning support of the comminution circuit."

Jan 1, 2019

By H. Qi, J. L. Feng, D. J. Li

"In the present paper, the characteristics of the granite burst under loading/unloading conditions was studied by means of both laboratory experiment and finite-discrete element method (FDEM). After gaining the mechanical properties of the granite samples under uniaxial compression conditions, the parameters taken as input arguments in the FDEM modelling were then carefully calibrated so as to provide some basic data including Young’s modulus, Poisson’s ratio, uniaxial strength, Lame constants, cohesive strength, and frictional angle for further being used in simulating granite bursts. All the simulating results by the FDEM were basically in agreement with that obtained from the uniaxial compression test and triaxial granite bursts in laboratory, respectively. This study shows that that such computational mechanics of discontinua can be employed to gain powerful insight into the failure mechanism of granite burst, which could also be a useful tool to clarify the collapse mechanism of rock structures in rock engineering design and rock test scheme optimisation. INTRODUCTIONBased on discontinuum state a priori, discontinuous modeling techniques that are commonly referred to as discrete element methods (DEM) treat the material directly as an assembly of separate blocks or particles, which was originally proposed by Cundall (1971) and Cundall and Strack (1979) from the viewpoint of analogous molecular dynamics simulation to better account for and understand the interaction between the blocks. The distinct feature of these formulations is that a constantly changing problem of geometry and contact conditions can be addressed by solving the equations of motion using an explicit time marching scheme (most often in a ‘leap-frog’ format), while updating contact force histories as a consequence of contacts between different discrete elements and/or resulting from contacts with model boundaries (Bicanic 1998). The most notable implementations of DEMs are arguably represented by the universal distinct element code (UDEC) (Itasca Consulting Group Inc., 2013) and the particle flow code (PFC) (Itasca Consulting Group Inc., 2012). Another formulation is the discrete crack framework that is based upon some criteria for an advancement of crack front, which is coupled with extensive local and global re-meshing while simulating by numerical methods such as finite element technique, commonly using fracture theories. Certainly, it is relatively easy to trace the propagation of single crack front governed by some principles of energy release rates (Ingraffea 1997) but tracing of multiple cracks leads to topological and algorithmic complexities. Otherwise, there is no consideration of interacting cracks in these formulations of finite element or enhanced finite element techniques (e.g., in XFEM and ABAQUS)."

Jan 1, 2015

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the decade up to 2010, mining revenues increased from 6% to 14% of Australian GDP, and minerals contributed 55% of total exports, with a growth in mining employment from 1% to 1.7% of the national workforce (Connolly and Orsmund, 2011). The growth in Australia?s minerals operations is mostly located in remote areas, or in rural communities with a limited population. As a result, operations have increasingly implemented long distance commuting (LDC) programs, often called ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO), as a staffing strategy to meet rapid industry growth in locations with limited local populations. The rapid expansion of the minerals industry has resulted in considerable public debate about the benefits and costs to all sectors of Australian society. In response to the concerns of constituencies from many parts of Australia, the Minister for Regional Australia, Regional Development and Local Government, The Hon Simon Crean MP, asked the House Standing Committee on Regional Australia on Tuesday 23 August 2011 to inquire into and report on the use of ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO) workforce practices in Regional Australia. The recently published report highlights the national interest and the diverse opinions about this practice in Australia. Resource extraction companies have developed several options to meet the accommodation requirements of their long distance commuting workforce. In this paper, initial results are reported from an ongoing survey of FIFO (and other non-residential) resource industry workers (n = 286) in the Australian resource extraction industries. The purpose of this study was to better understand how accommodation arrangements may impact on the health, wellbeing and job satisfaction of non-resident workers; and to attempt to find a relationship between different accommodation variables and workforce wellbeing and retention. In doing this it investigates evidence for the linkage between accommodation factors, hours of work, health, well-being, job satisfaction and job retention in the LDC work force.

Aug 1, 2013

By David Davidson

Overview- Points To Be Addressed ? Review the building blocks of a successful and vibrant industrial economy ? China?s current position in the global economy ? China?s voracious appetite for raw materials ? Distortion in import/export trends ? Areas of strategic importance for China - Steel and its components - Agriculture self sufficiency - Energy now and for the future ? Do current valuation techniques fairly value ?strategic? assets? China ? The Economical Miracle - Massive shift in population from rural to urban - ?Middle class? growing rapidly, hence strong consumer growth - China is the manufacturing center for the world ? cheap labour and - modern facilities - Infrastructure build out ?US$585b stimulus package and 5 year plan - Rail ? 30,000 kms of new track planned by 2020 - Power ? 50% capacity increase, including 35 nuclear reactors - 100 major new airports - State of the art process and manufacturing facilities - Port capacity ? 100m TEU capacity increase by 2020 Class 1 national highway ? 35,000 km?s by 2020

May 1, 2010

By P. G. Claridge, G. P. Holmes, M. A. Redfearn

"IntroductionThe purpose of this chapter is to describe current practices in operation and maintenance of flotation circuits in Canadian mineral processing plants. The chapter consists of five sections covering description of equipment, typical flow diagrams, operating practice, instrumentation and maintenance. The approach to this subject matter is intended to be practical in nature, hence no deeply technical treatment of flotation theory will be included.Flotation is an extremely common method of beneficiation of ores. Reasons are the relatively low cost of flotation compared to many other processes, the wide range of minerals to which flotation may be applied and the high efficiency of separation which can usually be achieved. The flotation process as we know it today has been developed within this century and it has had a major impact on the mining industry. While flotation is commonly considered to be important because it provides a relatively simple method of separating minerals in complex ores, the availability of flotation has also made a multitude of mineral deposits in Canada into economically viable mining operations because it allowed production of a concentrate of valuable minerals from the ore. These concentrates could then be transported from geographically remote locations to centraHzed plants for further processing, although the existence of the remote and perhaps small ore body alone would not have justified installation of metallurgical processing plants on site and the grade of ore would not have justified direct shipment of ore.Some of the more common minerals concentrated by flotation are sulphides of copper, nickel, cobalt, iron, zinc, molybdenum, lead and arsenic, as well as non-sulphides such as sodium chloride, potassium chloride, phosphates, silicates, chromite, fluorite, limestone and coal. Precious metals are also recovered by flotation, generally in association with another sulphide mineral."

Jan 1, 1989

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By R. G. K. Morrison

As mines grow deeper, the problem of ground control becomes one of increasing importance. The literature on the subject has grown extensively in the past few years, but is still far from conclusive. Detailed and precise observations are on record covering most phases of the problem, and control measures have progressed to the point where, in a large measure, they are effective. The success of methods to date must be attributed to the efforts which have been exerted to reduce convergence of stope walls and to the realization that a regular progression of stope faces approaching longwall has a beneficial effect. This paper attempts to explain the relationship between these two factors and the general problem of ground control. The problem at present lacks the co-ordination of the practical with the scientific outlook, but fortunately as time goes on there are indications that our scientific friends are becoming more interested and more familiar with the practical issues involved. Opinions vary widely regarding the mechanism of the problem and there are several schools of thought, two only of which will be discussed. One associates the incidence of rock-bursts with the stresses built up by a sagging hanging-wall, while the other takes the view that stresses primarily responsible for the sagging hanging-wall are also the cause of rock-bursts. The first group starts its reasoning from the convergence of the walls, probably the most conspicuous feature of deep mining, and works back to the conclusion that rock-bursts are in sorne way due to the breaking up of the sagging layers. The second group begins with the stress zone apparent around excavations at depth and follows mathematical conceptions based on certain assumptions which, in the absolute sense, are known to be inaccurate, but which are justified by the similarity between the conclusions reached and the results obtained in practice. This reasoning is followed to the point where rock-bursts result from the failure, under stress, of rock in situ, quite independent of wall convergence.

Jan 1, 1939

By R. S. Boorman, H. G. Ansell

"Poor separation of lead from a copper concentrate of a major base metal producer was thought to have resulted from copper (0.2-0.4%) in the galena which caused it to float with chalcopyrite. No inclusions of copper mineral were detected which could account for the flotation of galena. The tendency for copper-bearing galena to float with chalcopyrite was confirmed by Hallimond-tube experiments in which the floatability of copper-doped synthetic galena (0.1-0.4% Cu) was approximately four times as high as copper-free galena. The difference in the cell edge (5.9338 ± 0.0003 A, Cudoped galena; 5.9361 ± 0.0002 A, Cu-free galena) indicated that the copper was lattice-bound and did not occur as submicroscopic mineral inclusions."

Jan 1, 1973

By Nicola Robjohns, Kenneth A. Grace, Jane Spooner

"The important volume end use sectors for the rare earth elements and yttrium continue to be in steelmaking, petroleum cracking catalysts and glass polishing. The market sectors which may provide future high volume demand, to replace the older sectors where demand has declined over the past decade, include magnets, automobile catalysts, ceramics and superconductors. Increases in production capacity in all major rare earth producing countries are expected to restrain large price increases for high purity rare earth oxides over the short term. A sharp increase in demand for yttrium in advanced ceramics and superconductors would lead to a shortage in separation capacity, however, and to a corresponding rise in prices for separated rare earths.IntroductionWhile visiting the Geology Department of the University of Toronto in 1981, Professor Lu from the Institute of Geochemistry of Academia Sinica at Gweiyang in China introduced one of his seminars with the observation that in China, rare earths are not rare at all.Indeed, while being rare in terms of abundance as measured by, say, the Clarke scale, the rare earth elements, like many other low abundance elements, are subject to geological, geochemical and mineralogical concentration.The rare earth elements comprise the fifteen inner transition elements of Group IIIB, Period 6, of the periodic table, from lanthanum to lutetium (the lanthanides), as set out in Table 1. The rare earths constitute a distinct group as they have extremely similar chemical characteristics due to the uniformity of their outer electron shells. The element yttrium is usually, by convention, included in the rare earth group as it occurs with the rare earths in nature and has properties very similar to them.The rare earths are divided into two subgroups, the ""light"" rare earths, made up of the first seven elements of the series, lanthanum to europium, and the ""heavy"" rare earths, comprising the remaining eight elements, gadolinium to lutetium, plus yttrium. These two subgroups are also referred to as the cerium subgroup and the yttrium subgroup, respectively. The subdivision is based on differences in the atomic radii resulting in somewhat different properties for the two subgroups."

Jan 1, 1991

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35&apos;W, latitude 49°25&apos;N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By Nicole Peter

When introducing digital training technology a practical approach helps address cultural concerns.  Solutions to help create acceptance are discussed.  Resistance to change may be deeply rooted in traditional mine training personnel.  Traditional training staff members may consider themselves less digitally-savvy and resist technological methods available to them. A transitional approach intended to help mitigate or resolve resistance is presented as a continuous improvement pathway toward full adoption.  This presentation contends every mine should welcome the benefit of a digitally connected critical enabler.  The adoption of a digitally savvy learning centre is often viewed a disrupter to existing practice.  Given a commitment-driven learning centre model, technology offers the opportunity to transition from a compliance-based training model to one of competence.  Learning and Development practitioners should welcome the latest advances in neuroscience, Bloom’s taxonomy of learning model, and principles which guide mine safety training as outlined by the Lowell Institute for Mineral Resources at the University of Arizona. By employing digital applications to include animation, game-based simulations and immersive Virtual Reality (VR) these technologies create a viable digitally-savvy learning centre. We will outline the ingredients of a digitally enabled, or VR, Learning Centre to offer some observed benefits, successes, and potential short-comings. Much excitement in the industry surrounds implementation of simulation and/or VR headset training.  Given fair consideration of these as a ‘fit-for-purpose’ solution we examine the paradigm shift required to create real results for on-the-job learning.  Interim steps may be needed to meet the cultural transformation.   Simpler forms of VR, in the form of 3D models and VR environments as displayed on a large interactive touch screen, can serve to bridge this challenge and address a group learning environment. Features of the interactive 3D technology and ease of adoption are presented.  Usage of the touch screen is similar to that of a smart phone. It may be implemented as an obvious transitional tool.  To help describe merits of the interactive touch screen the presentation points out these sample underground and surface mine training applications. There are 3-D simulations such as ventilation, emergency response, support installation, and mine cycle and activity scheduling programs. These applications offer the ability to conduct entry examinations, complete digital pre-use checklists, and perform planned task observations in the virtual world of work. The tool may be used to teach the flow of hydraulics and do fault-finding on machinery such as loaders and dump trucks. Learners may navigate in a virtual mining environment to identify hazards, detect and assess abnormal ground conditions, address poor design features, and alleviate traffic constraints. It is possible to use connected physical controls to navigate machinery in the virtual environment. We conclude the presentation with a “compare and contrast” approach to cite potential cultural benefits by adopting a transitional method. 

May 4, 2025

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001