Search Documents

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one&apos;s thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By E. Godin, M. Rigaud, S. C. Panigrahy, I. Malinsky

"RésuméDes boulettes de concentres d&apos;hématite spéculaire à basse silice ont été produites en substituant la bentonite par de la tourbe, adéquatement traitée, additionnée d&apos;une faible quantile de soude caustique durant le boulettage. La réductibilité de telles boulettes et leur gonflement pendant la réduction ont été évacues, en utilisant quatre mélanges gazeux différents, formes de H2 - CO - N2.L&apos;influence du pouvoir réducteur du gaz utilise, sur le gonflement des boulettes, à été mis en évidence. Quelles que soient ces conditions réductrices, les propriétés mesurées sur les boulettes liées a la tourbe sont comparables aux propriétés obtenues avec des boulettes traditionnelles liées à la bentonite.ABSTRACTAdditions of peat moss and small quantities of NaOH during balling of low silica specular hematite concentrates have eliminated the need to use bentonite as a binder. The reducibility and swelling of such pellets have been evaluated using four different gas mixtures, consisting of H2 - CO -N2. The influence of the reducing power of the gases, on the swelling behaviour of pellets has been documented. Under the different reducing conditions, this new type of pellets exhibit properties similar to the ones obtained using bentonite."

Jan 1, 1987

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By J. F. J. Thomas

"AbstractBoth the quantity and quality of waters available as raw materials are important to Canadian industry and to the national economy. The huge demands of many Canadian industries is illustrated by tabulated figures, based on the 1950 Canadian production of certain products, and on United States figures for the gallons of water required to produce a unit quantity of each product. It is suggested from comparison with American survey results and figures that Canadian industrial water consumption is 1 to 11/2 billion Imperial gallons per day. Since present information on Canadian usage is meagre and it is not certain that American survey results can be directly applied to Canadian industry, this estimate must await confirmation in future studies.The hydrologic cycle and the principal factors affecting the quantity and quality of water, namely, climate and season, topography, geology, vegetation, and human activities, are discussed and the principal salts dissolved in water which affect industrial use are enumerated.The present survey studies by the Mines Branch on water quality are outlined. Besides chemical analyses of municipal water supplies within a watershed, periodic sampling and analyses of major surface waters for a one-year period is being carried out. The importance of studies on seasonal variation in quality is stressed by comparing the dissolved salts in various river waters with river flow. Figures showing such relationships in the Rideau river and Ottawa river at Ottawa, the Columbia river at Trail, B.C., and the Battle river at Unwin, Sask., are presented. Different rivers show different quality changes with changing flow, and possibly only after long-term studies can the relationships be predicted.Quality studies on water may be as important as studies on many other raw materials. The quantity of the raw material, water, is not inexhaustible nor is the quality indestructible, and more realization of its importance, followed by conservation and intelligent use, is desirable."

Jan 1, 1952

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Eldon L. Brown

Location and History The Sherritt Gordon property is located in northwestern Manitoba, about 100 miles north of The Pas and 40 miles northeast of Flin Flon. It is connected with the Manitoba Northern railway, which runs from The Pas to Flin Flon by a branch line, 42 miles in length. The location of the property is shown on the sketch-map, Figure 2. The ore deposit was first discovered by Philip Sherlett, a Cree Indian, in 1922. In 1924 Sherlett&apos;s claims lapsed and the ground was re-staked by Carl Sherritt and Dick Madole, and was optioned by them to J. P. Gordon in the summer of 1925. Gordon re-optioned the property successively to three well-known mining groups, one of which did some surface trenching .and put down 28 shallow diamond-drill holes before dropping their option. In the latter part of 1927, a Company known as Sherritt Gordon Mines, Limited, was formed to take over the property, and preparations were made for systematic development work. Preliminary Development In order to fill-in gaps left by the original drilling, a light diamond-drill outfit was flown-in to the property from the Hudson Bay railway in the early fall of 1927. Ten shallow holes were put down before freeze-up .and a considerable amount of surface trenching was completed. Based on the results of the surface trenching and the shallow diamond-drilling, an extensive development campaign was outlined. A winter road, 90 miles in length, was cut from mileage 55 on the Hudson Bay railway, and during the winter of 1927-28 a total of 2,600 tons of freight was hauled-in to the property. This freight included four complete diamond-drill outfits, two complete mining plants, building material for two sets of camps, and supplies for one year&apos;s operations, including 105,000 gallons of fuel-oil for Diesel engines.

Jan 1, 1933

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By T. S. Li, D. Ilievski, I. Livk

Micromixing of the fluid and the particulate phases in a continuous gibbsite precipitator was investigated for three different micromixing states, namely maximum mixedness (MM), complete segregation (CS), and maximum mixedness of the fluid but complete segregation of the particulates (MMF-CSP). The influence of the micromixing on continuous precipitation of gibbsite was studied at different precipitation conditions via simulation. Three different cases were considered with respect to the precipitation kinetics: (1) gibbsite secondary nucleation is favoured with slow crystal growth and agglomeration rates; (2) gibbsite crystal agglomeration and growth are dominant mechanisms with secondary nucleation suppressed; and (3) gibbsite crystal growth is the only relevant phenomenon. Simulation results for the cases (1) and (3) showed that the crystalline products for both the MM and MMF-CSP micromixing states were very similar, but the product obtained from the CS micromixing state was considerably different. This indicates that at those precipitation conditions the fluid micomixing has the dominant effect on the product properties, and the particulates micromixing effect is insignificant. However, when operated under the conditions of fast crystal growth and agglomeration kinetics, i.e. case (2), both the fluid and the particulates micromixing were found to affect the precipitation process, resulting in a significantly different product. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists ofCIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation&apos;s entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007