Search Documents

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

By W. Duyvesteyn, B. Sabacky, T. Spitler, D. Verhulst

"The Altair TiO2 pigment process is based on hydrochloric acid leaching of ilmenite at high-acid concentration. Titanium is transferred by solvent extraction into a high-purity aqueous stream with a high titanium concentration. HCl gas is recovered by pressure-swing distillation and is used to regenerate the leaching solution.A new method of TiO2 recovery in dense film with simultaneous dehydration and hydrolysis provides great flexibility in adjusting the characteristics of the TiO2 pigment product.Modifications of this method lead to a flexible, low-cost, high-tonnage process first for the production of nano-sized TiO2, and later for stabilized zirconia-based nanomaterials and nano-sized titanates.IntroductionProcesses for the production of TiO2 from ore by a hydrochloric acid route have been proposed in the past. Most of these processes dissolve impurities and recover TiO2 as a residue or as a hydrolyzed phase in the original solution (Turner, 1948; Berkovich, 1975; Morris, 1982; Judd, 1986; Chao, 1993). Solvent extraction of titanium after leaching in aqueous HCl has also been studied (Tsuchida et al., 1982; Narita et al., 1983) or at least mentioned as an alternative (Ellis, 1963). A number of small-scale studies on leaching and solvent extraction in both sulphuric and hydrochloric systems have appeared recently (John et al., 1999; Lanyon et al., 1999; Sole et al., 1999. As far as we know, only Kerr-McGee (Morris, 1982) and a plant in India and one in Malaysia use a hydrochloric acid route (20 wt% HCl) to commercially produce synthetic rutile.The Altair process originated in a search for an economical method to treat high-magnesium ilmenite deposits, while avoiding the production of a waste metal salt by-product. The first attempts aimed at producing pure TiO2 by leaching out the impurities. Further work centred on completely dissolving the ilmenite in concentrated hydrochloric acid and reprecipitating TiO2. To decrease the impurity level in the product, solvent extraction of titanium into a purified stream was introduced. It also became clear that to take full advantage of the increase in leaching efficiency provided by concentrated acid, it was necessary to regenerate HCl gas."

Jan 1, 2002

By Fraser Rowe

This paper discusses the philosophies, strategies, goals and pitfalls in automating a mine schedule. The intention of the paper is to give an open and honest view of who could benefit from moving to an automated system, what you can expect from such a system, and what you should be aware of. Many companies feel that moving to an automated mine planning solution will allow the mine scheduling engineer to push a button and walk away, but the reality is that is hardly ever the case. Part of that awareness comes from understanding what is meant by ?automated mine scheduling?, and this paper address that. By contrasting what is meant by ?manual scheduling? and ?automated scheduling? it is hoped that the reader can gain an appreciation of the entire process.

Oct 1, 2009

By Richard Poulin

Rehabilitation of mined out areas is often enforced by environmental bonding. It is usually assumed that this process provides financial assurance that rehabilitation will be carried out as agreed at the permitting stage. Shortcomings of the current practice in environmental bonding for mining are reviewed. Of particular importance for the public, for governments and for the environment is the absence of protection against cost overruns and companies defaulting before the bond amount is entirely paid. Elements of solution are identified through the emergence of environmental insurance as a complement to bonding for cost overruns and defaults. A cover of environmental catastrophes could also be added, hence reducing the risk for the public and the environment. We examine the merit of creating a captive insurance company under the responsibility of the mining industry. The use of insurance techniques would incorporate a genuine risk management dimension to the financing of rehabilitation.

May 1, 2004

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

By R. A. Bergman, C. A. Pickles, J. M. Toguri

"Black calcium cyanide is utilized mainly as a reagent for gold extraction. It is produced by reacting calcium cyanamide, sodium chloride and calcium carbide at temperatures in the range of 1200°C to 1400°C in a smothered arc furnace. The equivalent sodium cyanide content of the product is in the range of 45% to 50% and the calcium cyanamide conversion efficiency is in the range of 90% to 95%. Since black cyanide contains impurities such as salt and lime and also because the conversion efficiencies are below 100%, the product contains unwanted materials which significantly increase the shipping costs.The impurity content of the raw materials can not be lowered without increasing their cost and/or the processes to produce them, and therefore the present research was focussed on studying those factors which affect the cyanide grade. The major variables investigated were: the heating rate, the reaction temperature, the salt to cyanamide ratio, the nitrogen content of the calcium cyanamide, moisture additions and calcium carbide additions. It was found that each of these variables had a significant effect on the product grade. The highest cyanide content of the product was obtained for salt to cyanamide mass ratios of 0.55 to 0.60. The salt reduces the decomposition rate of the cyanide and, therefore, at low salt to cyanamide ratios and at higher temperatures, the product grade is decreased. It is likely that the salt evaporates at the higher reaction temperatures and this decreases the cyanide capacity of the melt. High heating rates minimize the residence time and thus salt evaporation is reduced and higher grades can be obtained. As expected, the cyanide content increased with the nitrogen content of the cyanamide. Calcium carbide additions resulted in an increase in the product grade. The presence of small amounts of moisture in the charge caused a significant decrease in the cyanide content of the black cyanide. An equilibrium reaction is postulated in order to explain the black cyanide process and in particular the effect of calcium carbide on the product grade."

Jan 1, 2002

By John Dasher

The analyses reported on in this paper indicate that there are hydrometallurgical routes from sulphide concentrates to copper that are potentially competitive with smelters which are not permitted to emit sulphur oxides. The various hydrometallurgical processes, and their economics, are discussed.

Jan 1, 1973

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability. The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employes to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed."

Jan 1, 2002

By Jamie Archibald

The Department of Mining Engineering at Queen?s University conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part II of the study, deals with underground operations consisting of backfill transportation and backfill placement. Part I of the study, which deals with surface operations consisting of backfill material supply and backfill plant preparation, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By Alfred Annor

Deep mining requires innovative approaches in ground control technology and the search for new ground support materials including backfill. There is a need to look at mine waste materials that may be available in deep mines to assess their suitability for use as composite backfill. Composite materials are widely used in all areas of engineering because of their unique and often superior structural properties compared to those of the singular constituent materials. Over the past few years, there has been a growing interest towards the investigation and use of various types of composite backfill materials as special applications fill in mines. A research project is being conducted at CANMET- Mining and Mineral Sciences Laboratories, Natural Resources Canada, to investigate the properties of potential ground support materials for use in deep mines. As part of this investigation, composite backfill materials were prepared by combining waste rock aggregates and mill tailings in various ratios, to determine their optimal mix proportions for strength development. A few cemented rockfill and straight tailings paste backfill samples were also prepared and were used as controls for the study. Two sample sizes were used for the investigation in order to evaluate the scale effects on the material behaviour. A set of samples were cured at 44 EC to simulate the anticipated temperature conditions in deep mines. A second set of samples were cured at 23 EC to provide engineering reference data. The test results show that compared to either the cemented rockfill or the straight tailings pastefill material, the composite backfill samples were the strongest and stiffest of all the test materials investigated in this study. The composite backfill samples also produced the lowest void ratio and porosity values compared to the cemented rockfill and the straight tailings backfill material. This paper will present the results of the laboratory investigations to date. It will also outline the on-going work at CANMET - Mining and Mineral Sciences Laboratories to further assess the ground support potential and viability of using composite fills in deep mines.

May 1, 2003

By D. E. Wakefeld

"My first reaction to Joanna LaForte’s discussion paper is that she has quite properly assumed that I would like the process of equitable participation between aboriginal landowners and mining companies to be a fast process. On the other hand, I have been a business lawyer long enough to know that the past experiences of the parties will have a significant effect on how they will proceed at any one time.In my article, I was trying to convey the importance of responding to the wishes, aspirations and fears of aboriginal communities in Arctic regions without land settlements. I agree that if it is necessary to wait for governments, the process will be quite slow. My article did point out that often aboriginal communities and mining companies who have become comfort-able that a project is in their mutual interest regard the government(s) involved as their common enemy. I agree that the education and training of aboriginals should “expedite the negotiations and end the power struggles equitably”. Also, I did not mean to suggest that the elders distrust of changes in traditional land use was solely due to concern for alienation and separation from their offspring; however, I suspect it is one reason for their caution. I also agree with this author that establishing opportunities that enable the young aboriginal community members to remain in the north and avoid the problems that await them in southern urban culture should be a common concern of the mineral developer and the Arctic aboriginal community.When this author suggests I am “overly concerned about how much land the aboriginals will control, how educated they may become, how ignorant they are of mining procedures, how objections from aboriginals will escalate expenses, etc.”, she attributes to me as “concerns” matters that were intended to be general information for my readers. My references to the increased land holdings and the improvement in education of aboriginal peoples was intended to deter mining companies from any attempt to be inequitable in their dealings with aboriginal communities."

Jan 1, 1996

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

By Laura Mottola

This paper outlines a framework for ensuring the success of the implementation phase that follows research and development of new mining technologies and systems. It is based upon recent and past lessons learned that have demonstrated the critical challenges to effective technology transfer, which frequently receive inadequate attention within the culture of the mining business. The paper focuses on mining automation implementation challenges and then outlines a Roadmap which is proposed as an integrated framework to deal with the key aspects of people, process and technology. This framework is built upon: assembly of a Strategic Team to develop a Roadmap; fully understanding the business requirements of the technology initiative; defining Key Performance Indicators in a Balanced Score Card; performing a Stakeholder Analysis to identify the affected groups; and finally developing a master Project Plan to execute the Roadmap.

Oct 1, 2009