Search Documents

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By Abdelkabir Maqsoud

Different management options and rehabilitation strategies are available for mine wastes that produce acid mine drainage (AMD). One of them consists in building a cover with capillary barrier effects (CCBE) on the tailings to limit the availability of oxygen, an essential component of the chemical reactions leading to the generation of AMD. Prior to cover construction, a monitoring strategy must be established to evaluate the response and performance of the cover system. The key parameters to monitor should include matric suction and volumetric water content in the CCBE, oxygen flux (and/or oxygen concentration) through and below the cover, and the main meteorological parameters for the impoundment. In this paper, different techniques available to measure the targeted parameters are described and their main properties are given. Recommendations (based on existing cases) on the location and the number of monitoring stations and on the measurement frequency for each monitored parameter are also proposed.

May 1, 2007

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By F. M. Makarinsky

"SynopsisThe Kanichee open pit mine and milling complex is situated approximately four air miles north-west of Ternagami, Northern Ontario, in Strathy Township. Mining and milling production commenced in January 1974.Milling throughput currently is at a rated capacity of 500 tons per day, seven days per week. A bulk nickel-copper sulphide concentrate is produced, and is trucked daily to the smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, some 120 road miles from Kanichee. Concentrate grades produced are in the order of 4.0% Ni and 8.0% Cu, with corresponding recoveries of 68-70% nickel and 86-90% copper. Stage additions of 100% guar-gurn solution reagent to the flotation cells for depression of talcose minerals, proved to be the major break-through for optimizing metallurgical performance.2. HistoryThe present Kanichee Mining property is known to old-timers in the Temagami area as the former Cuniptau Mine. Several attempts were made in the mid '30's and 40's to extract the ore at a profit, but each effort resulted in failure.In 1933-36, Cuniptau Mines Development Co. Limited, later called Cuniptau Mines Limited, sank a 245-foot vertical shaft and completed 2,200 feet of lateral work on the 100-140 and the 225 foot levels. Fifteen tons of ore were sent for testwork to the Mines Branch, Ottawa, Ontario.Cuniptau Mines Limited, in 1936, milled some 3,000 tons, and the resulting concentrate was put through a pilot smelter situated on the present mine site. Metallurgically, the smelting results were not encouraging, primarily due to the high melting point of the talcose minerals in the concentrate. From the period 1937-48, minor exploration work was done by Ontario Mining Corporation, Ontario Nickel Mines Limited, and Trebor Mines Limited. During the period 1948-49, 128 diamond drill holes, totalling 40,900 feet were evaluated by Trebor Mines Limited. In 1961, the name was changed to Ajax Minerals Limited, during 1968, five diamond drill holes were sunk, totalling 1,700 feet. Since that period the property has remained idle."

Jan 1, 1975

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

By M. Kerr, Petra Lampinen, Jinming Zhang, Petra Brodin, C. Hull, Nils-Johan Bolin, R. Asmatulu

"According to Darcy’s equation, the rate of dewatering varies as inverse square of the surface area of the particles to be dewatered and is proportional to the pressure drop across a filter cake. Thus, the difficulty in dewatering fine mineral concentrates can be overcome by using high-pressure filters. When treating ultrafine particles, however, it is often necessary to further dewater the filter cake using a thermal dryer. In the present work, novel dewatering aids that can reduce the pressure requirement have been developed. The reagents are designed to reduce surface tension, increase particle hydrophobicity and increase capillary radius, all at the same time. They were tested for dewatering mineral and coal concentrates in both laboratory and pilot-scale tests. The results show that the use of the novel dewatering aids can substantially reduce cake moistures and, at the same time, increase throughput. In this communication, the case history of using the reagents commercially at the Garpenberg concentrator is given. The use of the novel dewatering aids allowed the operators to use a vacuum filter to obtain desired cake moistures and obviate the need to use a thermal dryer.INTRODUCTIONDewatering is an integral part of mineral and coal processing operations, as it is necessary to remove water from concentrates (or clean coal) to minimize shipping costs, meet contract specifications, and recycle the process water. In general, the cost of dewatering increases with decreasing particle size, which can be attributed to the difficulty in removing the water trapped in the pores (or capillaries) formed between the particles constituting a filter cake.The various parameters affecting the process of dewatering, including the effect of particle size, can be understood in view of Darcy’s equation (Darcy, 1856):"

Jan 1, 2005

By Pierre Gratton, Gordon Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM’s goal is to improve the mining industry’s performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move to external verification of their performance in 2006. The presentation will describe the initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector.

Jan 1, 2006

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

By Godfrey MacDonald

"The East West Caribou deposit with an underground mine, concentrator and ancillaries is located 30 km west of Bathurst, New Brunswick. The Restigouche deposit, an open pit mine is 30 km west of East West Caribou. The ore will be trucked from the Restigouche site to the East West Caribou minesite.History:The East West Caribou ore body was discovered in 1955 and the subsequent metallurgical programme focused on producing a bulk sulphide concentrate. However, in 1966 a Mr. P.G. Kihlstadt of Anaconda did float a Copper-Lead concentrate and a Zinc concentrate. He also reported that as the grind became finer the recoveries improved. In 1968 the Mines Branch in Ottawa produced a Lead concentrate of 30 percent at a 60.5 percent recovery and a 52 percent Zinc concentrate at an 83.4 percent recovery.Laboratory testwork proceed the 1988 start up of our current concentrator and underground mine facilities. The concentrator was designed to produce a Lead ""rich"" concentrate and a Zinc ""rich"" concentrate which were combined to make a marketable Bulk concentrate. In 1990 the operation was suspended because of declining base metal prices, increasing smelter treatment charges, increasing operating costs and operating difficulties.The 1997 operating plan is to produce a Lead concentrate and a Zinc concentrate.The Restigouche ore body was discovered in 1989. The subsequent testwork done at Lakefield Research recommended the production of a Copper, a Lead and a Zinc concentrate. The ore reserve could not support a stand alone concentrator so the project was put on hold.Laboratory testwork was carried out at Lakefield Research to confirm compatibility of the East West Caribou ore and the Restigouche ore in their processing."

Jan 1, 1997

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Dean McDonald

The Committee Bay Greenstone Belt extends over 300km and is one of the largest unexplored greenstone belts in North America with excellent gold and diamond potential. Committee Bay Resources Limited holds over 550,000 acres of land with prospective geology in the Committee Bay area southwest of Melville Peninsula, Nunavut. Committee Bay is a typical Archean greenstone belt comparable to the Yellowknife, Red Lake, Kirkland Lake and other prolific gold belts. Drilling during 2003 at Committee Bay resulted in: 1) the discovery of high-grade gold-bearing quartz veins with silicification and sulphidation at Three Bluffs, and 2) the continuation of high-grade gold mineralization in the hinge area of the iron formation at Inuk. Gold mineralization at Three Bluffs is identified in iron formation and adjacent sediments and has been traced by drilling for over 700m. The Three Bluffs iron formation is open to depth and along strike where is has been traced on surface for over 6km. In January 2004 Committee Bay and joint venture partner Gold Field?s announced a $7.1 million exploration program for the Committee Bay project in 2004. A total of 8,000m in exploration drilling has been approved for the expansion of the Three Bluffs to the resource stage and drilling of at least five new target areas. Additional mapping, sampling and geophysics will be used to identify new gold targets along the very prospective Committee Bay belt.

May 1, 2004

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998