Search Documents

By Ma F, Yang Q, Ujihira M

The effect of stresses and acoustic emissions on the gas permeability of coal was investigated in the field and the laboratory in order to find an estimative method of the practicability of gas drainage. In the field, acoustic emissions and gas emissions during gas drainage drilling were monitored tentatively at some coal mines in Japan and China.In the laboratory, acoustic emissions from coal specimens in addition to gas permeability were measured during the triaxial compression loading in order to interpret the results monitored in the field. Besides, the opening of gas permeation channels in coal was considered on the basis of the experimental results.

Jan 1, 1991

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By M McDonald

KiwiRail has a goal of significantly improving passenger rail services to west Auckland, as part of its DART (Developing Auckland’s Rail Transport) suite of projects. The New Lynn Rail Trench (NLRT) project was a significant component of this work. The NLRT project facilitates essential doubletracking of the Western Auckland line, and provides a new commuter transportation hub within a busy town centre.The 1.5 km stretch of track through the New Lynn town centre has bisected the township for over 80 years. Double-tracking the line provided the opportunity to grade-separate road and rail, which would help to re-connect both sides of the township and enhance public amenity and safety.KiwiRail employed an Early Contractor Involvement (ECI) procurement model engaging a consortium comprising Fletcher Construction, Beca Infrastructure and Synergine to develop a Design and Construct solution.With weak soil conditions and high groundwater levels, a diaphragm wall construction method to form the trench walls was selected as the best solution. Further challenges to construction included working within a narrow rail corridor constrained by buildings along much of the boundary, and a requirement to keep the existing line open for rail services. Detailed construction planning was required to ensure rail and construction safety in a constrained space whilst building the trench walls, propping these walls during excavation, and constructing the base slab in the most efficient way possible.This paper will detail the geotechnical conditions and the additional constraints that made this rail trench a challenging structure to design. It will also describe the fi nal design and construction methodologies that were employed, that allowed very successful completion of the project.Additionally, this paper will review the design and construction lessons applicable to the current Victoria Park Tunnel project, and indeed for all future cut and cover tunnel projects in the Auckland isthmus.

Mar 8, 2011

By W Mez

The German mining industry uses different residues for backfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes, a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the DMT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer a secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

It is possible from simple gas behavioral theories to develop more complex relationships which allow prediction of transport phenomena such as diffusivity and viscosity of gas mixtures. Such physical data can be used in engineering calculations for both bulk gas movement and gaseous chemical species movement. Both of these are important in the solution of mines ventilation systems. There are specific limits of flammibili!'y of some common mines gases.

Jan 1, 1983

Good morning. I am very pleased to be invited to present the Opening Address to this inaugural New Zealand Minerals & Mining Conference. It is indeed a pleasure to see so many representatives of this industry, which is so important to New Zealand's economy, present here today.   I extend a warm welcome to all delegates, particularly those from outside New Zealand. To those of you who have travelled from offshore, please closely observe our industry, and do not hesitate to ask Crown Minerals staff here for any further information you may want. I trust you will soon come to the same conclusion that my two following speakers have; that New Zealand is a good investment destination, and further that many of you will decide to invest in New Zealand's minerals and mining industry.   In New Zealand the minerals industry - minerals, coal and petroleum - together constitute an approximate $2.5 billion per year business. In broad terms this is about 3% of our Gross Domestic Product.

Jan 1, 1997

By Chen J, Zhu D

A detailed study on oil agglomeration of fine metal oxide particles is presented in this paper. The major content embraces several aspects which may possibly reflect the current trends in oil agglomeration such as the effect of chemical and physical parameters, the activation of target minerals and the deactivation of gangue particles, the mechanisim of bridging liquid and the kinetics of oil agglomeration process. Systems of ilmenite-feldspar, manganese dioxide - quartz were seperated successfully through oil agglomeration followed by decantation or flotation technique respectively. A triple mixture of vandium-bearing titanomagnetite ilmenite and feldspar was processed satisfactorily using a composite technology: oil agglomeration-decantation-magnetic concentration.

Jan 1, 1993

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

By Roberts M. L

Long Shaft was initially developed using a rail haulage system on every working level comprising battery electric locomotives and granby trucks loaded by rail mounted rocker shovels. Production was commenced using conventional hand held cut and fill mining methods. In an effort to improve productivity and reduce operating costs a mechanised cut and fill stoping method evolved to suit the wider sections of the orebody. To further improve productivity and reduce costs the mechanised levels of the mine are progressively being redeveloped to enable the use of trackless diesel haulage equipment. An added benefit of trackless haulage equipment will be the ability to place development mullock into stopes as Fill.

Jan 1, 1988

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

By Pollard D. M

In the batch phase disengagement test, an organic and an aqueous phase are mixed together for a known period to produce a dispersion which may be either organic continuous (aqueous phase droplets) or aqueous continuous (organic phase droplets). The continuity of the dis- persion will depend upon the method of init- iating the dispersion, the conditions under which the system is operating, such as temper- ature and impeller speed, and the properties of the liquids, such as viscosity, inter- facial tension and solute content. Once the dispersion has been agitated for the required period, the agitator is turned off and the position of the coalescence interface and the sedimentation interface recorded as a function of time. This will produce a plot similar to Figure 1, where the overall dir- ection of travel of the droplets of dispersed phase is away from the sedimentation inter- face and towards the coalescence interface where the droplets coalesce with the homophase.

Jan 1, 1987

It is recognised by the current JORC (1999) code that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological continuity and grade continuity. No prescribed criteria and rules will work for all situations or even between different ore types within the same deposit. Also these criteria and rules are sometimes applied without a clear understanding of their appropriateness, accuracy or correct implementation. For these reasons case studies are useful to evaluate and compare criteria commonly used to assist in resource classification. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody are used as the basis of a case study for the above-mentioned purposes. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce a random sample grid, a semi-random sample grid and a regular sample grid. Using nearest neighbour, inverse distance squared, ordinary kriging and sequential gaussian simulation, block iron grades are estimated using these three blasthole data subsets as inputs. This provides four groups of estimates with the ordinary kriging estimate based on the complete blasthole dataset being considered to represent the true estimate of iron grades. Also generated during this process are estimates of the error for each block. These error estimates range from the simple, such as drill spacing, through to more advanced methodologies such as kriging efficiency and simulation. These estimates of grade and grade estimation error are then compared to the true estimate using graphs and statistics. In order of increasing accuracy the block grade estimation and simulation methods were nearest neighbour, inverse distance weighting, ordinary kriging and finally conditional simulation. The simulation in some instances doubled the accuracy of individual block grade estimates when compared to nearest neighbour and inverse distance weighting estimates. It was found that many methodologies for estimating the error of individual blocks performed equally well with only methods such as average drill hole spacing and classification by search ellipse pass number performing poorly. An approach on how to convert the abovementioned error estimates of individual blocks into a meaningful JORC classification is also discussed. Although advanced non-linear resource estimates are applicable, most iron ore mines are still using relatively straightforward methods. The use of blasthole data and some simple linear interpolation methods and simple linear based error estimates makes this study repeatable for most iron ore sites and their resource geologists. This style of investigation is recommended as a useful approach for the Competent Person to apply to their deposit and thus better select, implement and understand the criteria used for resource classification and provide more consistency and confidence in the resource classification process.

Jan 1, 2002

There are countless petroleum and mineral fiscal systems throughout the world. This is because many petroleum and mineral producing countries have developed their own methods of calculating government take through fiscal evolution or individual negotiation. Those countries fortunate enough to have petroleum and mineral reserves within their national boundaries are naturally reluctant to yield this resource without a reasonable return for their population. As resource companies are perceived to be enormous conglomerates with endless amounts of cash and resources, governments and the general public demand reasonable division of production while these finite resources last. On the other hand, because companies engaged in the exploration for, and production of, minerals, oil and gas have to be large or lucky (preferably both) to sustain the great physical and commercial risks involved, the income and profit figures look so large that the general public sees them as an acceptable target for taxation. Taxation of the resource industry has been one of the industry's greatest cash flow problems through the years. Allen and Seba (1993) attribute this to the fact that the most equitable tax systems are those that affect the widest possible total of the population.

Jan 1, 1996

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

By Smith I. K

A Data Acquisition System with a capacity to monitor 2000 analog instruments has been installed at the mines operated by the Zinc Lorporation, Limited and New broken hill Consolidated Limited (ZC/LVbHC), New South Wales, Australia. Since commissioning in March, 1982, the system has proved its value in providing up-to-date information to both Rock Mechanics and Mining personnel. The paper describes the function of the major software and hardware components of the system, and identifies the advantages that an on-line monitoring system provides in the day-to-day operation of a large underground mine.

Jan 1, 1983

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990