Search Documents

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

Underground mines in Australia and worldwide are extending to greater depths. The effect of depth brings a number of challenges to mining engineers including geotechnical, ventilation, haulage and selection of mining method. The main effects of depth from a ventilation perspective are increased heat and humidity leading to reductions in productivity, occupational safety and health issues and the potential for fatalities. Numerous approaches have been undertaken over the years to mitigate against these effects. In this paper a review of various approaches to improving climatic conditions at a number of mine sites worldwide is undertaken. From these case studies it is argued that for mines at depth with the potential for a climate problem perhaps an alternative design philosophy to the established design philosophy should be utilised. In conclusion, the paper proposes some simple rules of thumb for use in mines with climate problems or the potential for climate problems.

Jan 1, 2008

The kinetics of chlorination of alumina and bauxite with CO/CI2 mixtures were studied in the range 300-1100°C. The temperature of prior calcination is critical in determining the reaction rates. An optimum chlorination temperature in the range 600°C-750°C was demonstrated such that there is no increase in reaction rates with increasing temperature. This lack of rate sensitivity to rising temperature is largely a function of the influence of gaseous diffusion gradients in the porous alumina together with a progressive decrease in surface area.

Jan 1, 1976

An intensely sheared and mineralisedIzone occurs in the Quartz Dolerite Greenstone (or Younger Greenstone) mass on, the western limb of the Kalgoorlie Syncline. This zone comprises the western part of the Golden Mile and has produced the greater part of the 33,000,000 ounces of gold produced to date from the main mining belts. A study of.th e general geological and structural features gives rise to the expectation that the lode shear system,will continue southward on a pitch similar to that of the maln syncline whose axial plane may be referred to as the "Boulder Dyke". Although payable ore has recently been found further south than previously, the expectation of large quantities extending southward from the present mining areas is Problematical.'

Jan 1, 1964

Increasingly, mineral operations need to manage water as a key business asset. Managing water solely as an environmental issue leaves a business exposed to social, cultural and economic risks associated with water. Adopting a company-wide strategic approach, which takes account of the true value of water will provide businesses with opportunities and risk protection. Rio Tinto has recognised the business imperative for water stewardship and has responded by producing the Rio Tinto Water Strategy. This strategy commits the company to managing water assets in a responsible manner, taking account of environmental, social and economic values. To incorporate the true value of water in site decision making, a new set of tools is required at the operational level. A key part of the strategy focuses on developing a framework to value water based on case study examples from around the Group. This paper presents progress on the companyÆs experiences in developing and implementing the water strategy.

Jan 1, 2006

By Christie AB

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database mangement system on a PC-type computer. The data are plotted as maps using the Maplnfo geographic information system (GIS) package. Thesholds separating anomolous values from background values are determined using the PROBPLOT univariant statistical package, which enables the descrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to sevelop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.]

Jan 1, 1995

By Thomas W

Due to record low tin prices and an uncompetitive position in world markets, the Renison tin mine has undergone three major phases of restructuring in the last three years. This has involved substantial job losses, almost all of which have been through voluntary retrenchments. Retrenchments took place in 1988, 1990 and 1991.The last phase of restructuring was the most dramatic, as many aspects of the operation of the mine were changed. New pay structures were introduced, and the miners' contract system was scrapped. Drastic pay cuts occurred in many areas, although the opportunity was also taken to increase pay at some of the lower levels where inequities existed. Work practices were changed, as was the management structure.

Jan 1, 1992

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

Open stoping dimensions are typically controlled by a number of factors including production drilling capacity, scheduling, fill constraints, orebody dimensions and host wall rock conditions. Frequently host wall rock conditions are the key control on stope dimensions. As a new mine is brought into production, there is a steep geotechnical learning curve for those associated with the development of the mine. Initially, the experience and observations gained at other mines is used to guide the stope design. As experience is gained at the new operation, site specific techniques can be validated for use. This has been the case at BHP Cannington, where a heavy emphasis has been placed on the validation of empirical stope stability techniques for site specific conditions and experience. A range of empirical and numerical techniques can be applied during the design of open stopes. The empirical techniques are an experience based application of known performance levels during the design of open stopes. The numerical modelling and structural tools can be used to compliment the empirical techniques so that an understanding can be gained of the likely stress and structurally controlled failure mechanisms.

Jan 1, 2000

By Fewings JH

When the mining and milling of 1100 Copper Orebody commenced, difficulties were experienced in producing a satisfactory grade of copper concentrate. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 Orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in an inherently flotable fine pyrite and silica fraction. The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to'the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1970

By M Miettinen

That microorganisms, both living and dead, and products derived from the organisms, can function as flotation agents and flocculation agents is abundantly clear. They can modify the surfaces of minerals. They can function as flotation collectors and as flotation depressants and activators. In many cases they or their products can function as specific flocculation agents. Problems that must be solved before such microorganisms or products from the organisms can be used in commercial operations include culturing the organisms at a cheap cost and reduction in dosages required for various separations. These tasks are formidable. However, the concept of using such natural materials in place of various chemical reagents that may be toxic is very attractive. An attempt is made to show some of the promise of microorganisms in mineral bioprocessing and to consider the problems that must be overcome before commercial application of the technology is realised.

Jan 1, 2005

Carbonation of reinforced concrete is a potential durability issue for vehicular tunnels. This is particularly the case where elevated carbon dioxide concentrations exist and when the design life is 100 years or more. The process of carbonation can result in loss of passive protection to embedded steel reinforcement and initiation of corrosion. Therefore, tunnel design needs to consider the potential for carbonation on internal surfaces and how design life can be achieved in severe environments. This paper examines methods for predicting carbonation and how deterioration can be mitigated through appropriate concrete mix design and construction practices.

Jan 1, 2008

By Wang Xia, Zhou Aiming, Shi Shengyi

Zhangmatun Iron Mine is situated in the suburbs of Jinan city, Shandong, China. Because of surface environmental constraints, no suitable site can be selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a doubleshaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two stopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining. Utilisation of cemented tailings backfill solves not only the problem of disposal of mill waste, but also the resource problem of providing backfill materials to the mine. The strategy also maximises ore recovery for the mine.

Jan 1, 1998

By Barber J

The manganese ore of Groote Eylandt is a shallow sedimentary deposit of Cretaceous age. There are a number of deposits which vary greatly in ore texture, density, percentage of matrix and thickness. The thickness in the present five operating quarries varies from 1-5 metres. The mine output in 1973 was 3 million tonnes of which 60% was blasted, the remainder ripped and bulldozed. The shallow deposit and its varying thickness create rather unique blasting problems which must be overcome in order to produce a minimum overall mining cost but not necessarily resulting in a minimum drilling and blasting cost per tonne. Future planning envisages the introduction of site mixed slurry explosives following test work and the application of a twin boom single operator rotary percussion drill. The paper outlines the overall developments,present and envisaged practices and the reasons for these changes.

Jan 1, 1974

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

Although geophysical methods of prospecting have proved indispensable in the search or oil deposits elsewhere; it is only 'in recent years that they have been used to any significant extent in Australia. The increase in their use has been quite remarkable over the past two or three years, due in Sao small measure to the encouragement given by means of Commonwealth subsidy. There is no doubt that the use of' geophysical methods will coxi-tinue to increase and this increase could be greatly accelerated as and when oil is discovered in commercial quantities,This review of their use A in Australia and the remarks and statistics are confined to work on the mainland. There has been, a substantial amount of geophysical work in Papua, but as operating conditions are so very different to the mainland Papua has been regarded as a separate province.

Jan 1, 1962

Engineering availability of the 120/200 tonne Wabco haulpak fleet at Mt. Whaleback was in the mid fifties and unstable. The project to achieve a reliable 66% during 1980 highlighted "plannable" maintenance, short cycle scheduling, condition monitoring, backlog control, and, above all, the importance of involving all affected people. It is not sufficient for consultants to design systems and make them work. The people who use the system must understand it, support it and "own" it. In this way, they will develop it and improve results after the outside help has been withdrawn INTRODUCTION In early 1979, PA proposed a programme to improve engineering availability of the Mt. Newman Mining fleet of 70 Wabco haulpak trucks of which 53 were 120 tonne and 17 were 200 tonne units. (Subsequently five 200 tonne trucks from Hamersley Iron were added to the fleet). The ore truck workshop was also responsible for 75 tonne trucks used as water trucks and general purpose vehicles. The need for action was clear. The fleet was achieving availability in the "mid fifties" with wide variations indicating that the fleet was becoming unreliable. Projected tonnages required a reliable 66% availability to be

Jan 1, 1982

By S McKnight, S Hall

Much of the research regarding the use of bacteria for the oxidation of sulfide minerals has been conducted using pure bacterial strains or synthetic minerals, often under ideal conditions, which does not reflect the conditions commonly encountered in commercially operating plants. This has also led to much conjecture as to the exact mechanism by which bacteria are able to enhance sulfide oxidation and as to which species of bacterial microflora are the most dominant. Recent advances in 16S rNA sequencing has confirmed that many of the bacterial species once thought to dominate commercial oxidation circuits were simply more willing to grow under the culturing conditions used and may only play a minor role in the oxidation process (Rawlings, 2002). Consequently this research will look at bacterial oxidation under conditions more reflective of commercial operations, focusing on the presence of organic carbonaceous material within a refractory sulfide orebody to be sourced from the Fosterville deposit of Perseverance Corporation Limited.

Jan 1, 2004