Search Documents

By Johnston G, Revy T

Dominion Mining Ltd. and the JKMRC have conducted a detailed investigation of the performance of two of Dominion Mining's gold treatment plants (Haveluck and Paddy's Flat). In terms of design each plant is considerably different. The Paddy's Flat plant uses a single stage SAG mill with recycle crusher, followed by single stage ball milling. The Haveluck plant uses the more traditional approach of multi-stage crushing and ball milling. The performance of these two plant designs in terms of energy efficiency and cost of comminution equipment, developed at the JKMRC, to accurately predict both power draw and size reduction characteristics at these plants is evaluated.

Jan 1, 1991

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

By A Thompson, E Villaescusa

The Western Australian School of Mines (WASM), Kalgoorlie, has been performing dynamic testing of reinforcement systems as part of the Minerals and Energy Research Institute of Western Australia (MERIWA) Projects M349 and M349A sponsored by WASM, the Western Australian State Government and the mining industry. These projects have resulted in the construction and commissioning of the WASM Dynamic Test Facility and a program of reinforcement system testing. The primary purpose of the WASM projects is to evaluate the performance of complete reinforcement systems when subjected to an axial dynamic load. The test procedure, monitoring and associated analysis enable assessments for each component (ie the element, the internal fixing mechanism and the surface hardware) of the reinforcement system. The performance of a reinforcement system is usually defined by a static force-displacement response to axial loading. However, this static response may not be applicable to dynamic loadings associated with violent failure of rock due to overstressing as mines progress to greater depths. It was therefore appropriate that the responses of reinforcement systems subjected to dynamic loading be defined and evaluated. The key findings from the tests on a number of reinforcement systems are presented and recommendations made regarding their application for dynamic loading.

Jan 1, 2008

By Pollard D. M

The BHAS copper-lead matte leach process, developed in Port Pirie, South Australia, has been in operation on a commercial scale since 1984. This process is one of many developed in the past decade to recover copper via the hydrometallurgical route. In essence, the process involves a single stage agitative leach of 100% -75um matte in an acid chloride-sulphate lixiviant with gaseous oxygen as oxidant. The leach temperature is controlled at 85¦C to assist with reaction kinetics. After leaching, divalent copper is recovered from solution via a conventional solvent extraction/electrowinning circuit to yield cathode copper for sale The BHAS matte leach process has several unique characteristics cf. other commercial oxidative acid leach processes. These include i) the use of gaseous 02 as oxidant ii) H2SO4 addition as make up acid iii) Relatively low chloride ion addition (30 g/1) For this reason, extensive work was carried out into the optimization of leaching by Meadows (1985). Variables investigated included ò Oxygen flow-rate ò Agitation intensity ò Leach temperature ò Free acidity ò Chloride ion concentration ò Matte particle size The current work was conducted to determine the effect of cooling rate, and hence mineralogy, on the leaching characteristics.

Jan 1, 1989

The nature of exploration in Australia is reviewed from its inception to the present time. It is seen as consisting of three phases: the first, prospecting; the second and third, mainly company-based activity. The first yielded the discoveries on which the mining industry was originally built. The great recent growth of the industry has been due mainly to the discoveries of the third. The technical, organisational, legis- lative and other aspects are reviewed. The overall result has been a very great increase in the known mineral resources and, viewed collectively, exploration is seen as providing the principal means of assessing, evaluating and building up the nation's mineral resources.

Jan 1, 1973

On Wednesday 11th November, 1970, a series of violent explosions occur-- red within No.1 Basic Oxygen Steelmak- ing (B.O.S.) furnace at the Whyalla Works of the Broken Hill Proprietary Co. Ltd., (B.H.P.) when the furnace was moved immediately prior to tapping. Water from a burnt out flux chute had flooded the bath while the furnace was tilted slightly towards the tapping side waiting to tap. Although no one was injured, dam- age in excess of $54 000 was caused to the hood and superstructure. The water hydrated the burnt dolomite refractory lining some of which sub- sequently collapsed exposing bare fur- nace shell over part of the cone.

Jan 1, 1975

By M Csar

The Nicolsons Find gold project is located 35 km southwest of Halls Creek in the east Kimberley. It was discovered in the late 1980s by John Nicolson and Stuart Skoglund, when high grade gold mineralisation within outcropping gossanous quartz reefs was found. The area has produced a modest 28 150 ounces of gold over two brief mining periods in 1996 and 2002 - 2003. Indicated and inferred resources as of September 2011 stand at 1 384 000 t at 5.58 g/t Au for 248 500 ounces of gold.The project is situated within the Halls Creek Orogen. Principal host units are metasediments and volcaniclastic sediments of the Koongie Park Formation. Minor mafic units are also recognised. Immediately east of these units, emplacement of the loadstone granite is believed to have provided the structural setting for the later gold mineralising event.Mineralisation is hosted within a broad, brittle-ductile arcuate shear zone about the western contact of the Loadstone granite. In the Nicolsons Find area, the shear zone strikes north-northeast and within the shear zone, gold is hosted in a series of narrow, quartz rich veins up to 200 m in strike length, plunging moderately to the north-northeast. To date, mineralisation has been drilled to a depth of 360 m below the surface. The veins are stepped or en-echelon in nature with low gold values towards the quartz vein limits where compression is inferred and higher grades present in the dilational body of the quartz veins. Gold is fine grained and can be present with or without associated sulfides. Sulfides are generally minor and consist mainly of arsenopyrite with traces of chalcopyrite, pyrite and sphalerite. Where present, sulfides are generally indicative of higher gold values.CITATION:Csar, M, 2012. NicolsonÆs Find gold project, East Kimberley, Western Australia, in Proceedings Narrow Vein Mining 2012 , pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

The paper contains the publication of timber shapes recovered from the Burra Mines during open cut operations in the 1970s. The timber was in the process of being disposed of for fire wood. All timber shapes still in existence in September 1990 were drawn.The collection revealed a number of different types of caps and legs. There were also end plates and wall plates from what appeared to be a hanging sets of shaft timber.

Jan 1, 1993

The use of operational research in mining is illustrated by simple examples of the techniques of simulation, linear programming, theory of sampling, and experimental design.Statistical simulation of the delays in answering telephones was used to compare the efficiency of alarm systems in collieries, and to determine stock control policy for a bin in mucking, filling, and tramming operations. Linear programming was used to help minimize transportation costs between collieries and washeries. The theory of sampling was applied to separate and balance the components of error introduced at the' various stages in the collection and reduction of routine samples of coal, and to the assessment of errors of estimates of grade in orebodies from drill samples. 'l'he principles of experimentaldesign were used to compare wear of different conveyor beltings and costs of battery and diesel locomotives in underground transport.INTRODUCTIONIn operational research some of the procedural techniques and professional attitudes of mind found among scientists and, in particular, mathematicians and statisticians, are applied to operational problems in industry ranging from policy making in the broadest sense to the humblest sampling procedures. These apply in mining equally with other industries.Anyone who reviews a procedure critically and in a systematic way may legitimately claim to be doing operational research. On the other hand, what is found in books on operational research is usually a collection of mathematical and statistical techniques which, though forming only a corner of operational research activity, illustrate the novel approaches to problems which characterize the discipline and which would probably not occur to the un...

Jan 1, 1962

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

Analysis of different environmental scenarios and to represent, spatially, of impacted areas is possible by the use of geoprocessing techniques, specifically Systems of Geographical Information (SIG). Through these systems it is possible to create dynamic mathematical models, constituting of a georeferenced digital database and employing the integrated data originated from several sources. In this context, the general goal of this paper is to apply this tool in an environmental analysis of a specific karstic area impacted by mining activities. In order to preserve a limestone site, internationally recognised by its archaeological features, including caverns, lakes and evidences of prehistoric ages, the Brazilian government has created the Lagoa Santa Environment Protection Area. This place is located in the proximity of the Belo Horizonte international airport. In the past two decades exploitations of dimension stones have increased in this area. These exploitations have been done without a mine plan promoting several environmental impacts. The objective of this paper is to analyse these activities using SIG as a basic tool to locate the main mining related impacts and propose mitigation measures including waste and tailings disposal and reshaping of the landscape and introducing a drainage system for the considered zone.

Dec 6, 2010

This paper considers the opportunities and problems which in-situ leach mining technology presents to the mining industry. These are exemplified by concerns addressed in the development of a proposal to mine uranium by in-situ leach techniques at Beverley in South Australia.

Jan 1, 1988

The purpose of this paper is to outline the current status of financing in the Australian Gold Mining industry and to discuss a number of developments that have occurred during 1983/84.Recognising the importance of equity financing various equity issues, including project valuation, will be discussed against the backdrop of an industry experiencing both rapid growth and a changing structure.Nothwithstanding the current tax exempt status of the industry there is a trend towards more debt financing. A number of financing issues will be covered and it will be shown howvalue can be created through astute financing planning.

Jan 1, 1984

Investigations into the flotation behaviour of single minerals, mineral mixtures and ores at the CSIRO Division of Mineral and Process Engineering have led to the development of sophisticated laboratory flotation testing equipment. Both routine and complicated flotation investigations can be conducted in a precise and reproducible manner using procedures and equipment that have been refined over many years of conducting careful batch flotation testwork. Several important advances in flotation research can be attributed to changes in testing procedure developed as a consequence of the availability of this equipment. The flotation cell and ancillary equipment is described and associated developments and techniques discussed.

Jan 1, 1992