Search Documents

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

Secondary steelmaking (or ladle metallurgy) has been developed as a post- steelmaking ladle treatment to produce steel of superior quality. Its rapid growth has resulted from quality improvements, productivity increase, operational flexibility and process route economics. Advances in secondary steelmaking are very impressive during the past decade, and many commercial systems have been developed for performing one or more of the following unit operations: degassing, atmosphere regulation, reheating, refining with synthetic slag, rinsing gas treatment, injection of solid materials and alloying. The metallurgical requirements imposed by the current competitive steel market include more precise analysis tolerances, minimum level of detrimental elements, improved cleanness, demanding service performance and better processability. In most cases, these requirements could only be realized by the application of appropriate secondary refining facilities. Continuing developments in simplicity of design, cost advantage, quick cycle time, improvements in peripheral services such as refractories, instrumentation and in-situ analysis, extensive exploration of new applications, and the use of computer, can be expected. An exciting future is predicted for the widespread adoption of secondary steelmaking to perform most of the major refining functions over a variety of steel quality. It will also become a vital link in the total steelmaking process for production of tonnage steel at the large integrated steelworks and the mini-steelmills.

Jan 1, 1986

I offer some comments which might complement the valuable recent paper by De Angelis et al (1987), on the newly discovered nickel-copper deposit at Radio Hill.The authors have accepted subdivisions and correlations by Hickman (1977, 1983) although they are disputed (Fitton, Horwitz and Sylvester, 1975; Horwitz, 1979; Horwitz and Guj, 1986).Also, in my opinion, more plausible correlations of the Sholl Belt with Whim Creek Belt have been shown, but not discussed, in Hudson and Horwitz (1986, Figure 1). Our suggested correlations and subdivisions have appeared in publications and reports which are not readily available, but it is gratifying to note that many of the observations and conclusions of De Angelis et al are consistent with our conclusions of the Whim Creek Belt.The units of the Sholl Belt (of Hickman, 1983), between the Sholl Fault (Shear Zone) and the overlying Mt Bruce Supergroup to the south, equate well with units of the Whim Creek Belt. A basalt, characterised by an abundance of vesicles and similar in many ways to the Wararnbi Basalt of Fitton, Horwitz and Sylvester (I975), is well developed at the base of the succession, particularly in the southern part of the area (Figure 1). It is overlain by acid tuffs (locally metamorphosed, such as at Whundoo Mine) and associated acid and mafic lavas, similar to those of the Mons Cupri area. The mafics in the succession are marked by the absence of the numerous cherty sedimentary intercalations, such as the Marble Bar Chert, which occur in the Warrawoona Group; and they also lack the intense chertification that is prevalent in all parts of the proven areas of Warrawoona Group rocks.The Whim Creek Group is overlain, locally unconformably (two to three km east of Mount Negri), by the Negri Volcanics which include here the Louden Volcanics (unit Abu of Hickman, 1977), (Horwitz, 1979). The negri volcanics are an alternating sequence of variolitic and quench textured lavas not dissimilar to the highest units of the Sholl Belt (Figure 1). They range from high-Mg basalt to tholeitic andesites (Glikson et al, 1986, pp 79 and 84). The whole succession of the Sholl Belt is estimated to be of the order of four km in thickness, more consistent with the two km thick (Horwitz, 1979, Figure 1) Whim Creek area sequence than with the much thicker Warrawoona Group sequences. The Whim Creek Group (including the Negri Volcanics) is considered to be a widespread grouping (Fitton, Horwitz and Sylvester, 1976; Horwitz, 1979; Horwitz and Guj, 1986) which is prevalent in the northern part of the Pilbara Craton. It is considered by these authors to include the Mallina Formation turbidites of the trough area of Ryan (1965). One component, the Mons Cupri Volcanic, is about 2.95 Ga (Richards and Blockley, 1984). Between the Sholl Fault and Egina, the Whim Creek Group is intruded by large ultrarnafic to granophyric ills of the Millindinna Complex (Fitton, Horwitz and Sylvester, 1975), dated at 2.860 ± 002 Ga by Gulson and Korsh (1983) near the Sherlock River (south side of Caines Well Granite area). The Millindinna Complex has been equated to the same magmatic episode as the layered complexes of the Sholl Belt by Fitton, Horwitz and Sylvester (1975, p 20).

Jan 1, 1988

By C V. Putnis, T Geisler, A Putnis

In nature, ilmenite (FeTiO3) undergoes weathering through oxidation and removal of Fe to form an apparently continuous series of compositions from ilmenite to pseudorutile (ideally Fe2Ti3O9), and with further weathering, to leucoxene. To determine the mechanism of acid-leaching of ilmenite to ultimately form rutile, we have carried out an experimental study of ilmenite alteration in autoclaves at 150¦C in HCl solutions. Resulting products were studied by X-ray diffraction, scanning electron microscopy, electron microprobe and Raman spectroscopy. In some experiments the solution was initially enriched in 18O and the distribution of the isotope in the alteration products mapped from the peak shift in the Raman spectra. The results indicate that the alteration may proceed in two stages, each with a sharp interface between the parent phase and the product. The alteration begins at the original ilmenite crystal surface and along cracks through which the fluid can migrate. The first alteration product is pseudorutile û no phases intermediate between ilmenite and pseudorutile were detected. The textural relationship between ilmenite and pseudorutile suggests a coupled dissolution-reprecipitation mechanism rather than a solid state continuous oxidation and Fe diffusion mechanism. The second stage involves a further dissolution-reprecipitation step to form rutile. Raman spectroscopy shows that the 18O is incorporated in the rutile during the recrystallisation. Throughout the alteration process the original morphology of the ilmenite is preserved although the product is highly porous. The rutile inherits crystallographic information from the parent ilmenite, resulting in a triply-twinned rutile microstructure.

Jan 1, 2008

In south-eastern King Island, sediments and lavas of possible Upper Proterozoic to Lower Cambrian age have been intruded by Lower Carboniferous granitic rocks.Within the contact aureole of the Bold Head adamellite north of Grassy the sediments and lavas have been metamorphosed to hornblende hornfels facies grade. The thermal gradient within the contact aureole was small, as the hornfelses exhibit no mineral zoning over a distance of 700 ft from the adamellite.Skarns occur both within the adamellite near its contact with the country rocks, and within the country rocks as partial replacements of three dolomitic limestone horizons. The latter type, the exoskarns, commonly have an andradite-salite mineralogy and carry economic concentrations of scheelite. These resulted from the replacement of carbonate beds due to both diffusion and infiltration metasomatism. Silica, tungsten, minor sulphides, and water were introduced from the adamellite, while aluminium and iron diffused from the enclosing pelitic sediments. Calcium released during marble replacement countered the loss of iron and aluminium in the pelitic hornfelses transforming them to diopside-rich rocks.Endoskarns within the adamellite are the result of two way diffusion across the contact; calcium, aluminium, and iron diffused from sediment to adamellite as silica, potassium, sodium, and water diffused from adamellite to the sediments. From estimates of the lithostatic pressure and mole fraction of CO2, the mineral assemblages of the hornfelses imply that the temperature of metamorphism lay between 530° and 710°C. This temperature range is in good agreement with minimum temperatures, between 610° and 710°C, for the recrystallization of the marbles of the contact aureole, calculated from the determinations of the solid solution of the magnesite molecule in calcite.

Jan 1, 1971

The art of flotation may be divided into two distinct branches, namely:-1. Collective flotation.2. Selective flotation.(1) Collective flotation is applied when all the valuable minerals in an ore are required in one concentrate, leaving ,only gangue minerals in the tailing. The method is applicable, for instance, to such ores as auriferous copper sulphides associated with gangue minerals only, or to silver lead ores low enough in zinc and other valuable minerals.(2) Selective flotation is applied when there are present in an ore two or more valuable sulphides, which cannot be subsequently efficiently treated unless they are separated from one another as well as from the gangue. For example, a silver-Iead-zinc ore, or a copper-gold-iron ore; where the iron is not required with the copper gold concentrate.In order to make these operations practicable chemical reagents have been developed, having power to exert definite actions on the various minerals when brought into contact with them in a water pulp.COLLECTIVE FLOTATION.In order to bring about collective flotation it is generally necessary to add to the pulp a frothing agent and an activator or activators for all the minerals which it is desired to float.SELECTIVE FLOTATION.The object of selective flotation is to activate the mineral which is to be floated, and at the same time to prevent all other minerals from floating.

Jan 1, 1936

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

Australis Mining N.L. operates a continuous mode carbon-in-pulp (CIP) gold plant, processing sand and slime tailings from previous gold mining operations in the Norseman area. Plant design is that of conventional countercurrent contact between pregnant pulp and activated carbon. Gold desorption is achieved by the Zadra process using near boiling tempera- tures and atmospheric pressure. Process water is drawn from nearby Lake Cowan (saline). The plant operates at, or above, design specification of 400 dry tonnes per day. This paper describes the plant design and operating processes utilised in optimising throughput and gold recovery. TNTDnPTTnmTnM Favourable world gold prices and substantial reserves of sand and slime tailings prompted Australis Mining N.L. to construct a gold extraction plant during 1981. The projected plant throughput was set so as to complete treatment of available tailings over a three year period. Metal- lurgical tests indicated that, with a regrind facility satisfactory gold recovery could be achieved using a countercurrent CIP process. Reflecting the entry of Australis Mining N.L. into its first large scale treatment operation, the plant design emphasised simplicity but effectiveness of Operation.

Jan 1, 1982

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

Solid Energy New Zealand Limited (æSolid EnergyÆ) is a state-owned coal mining company, producing 4.0 Mtpa from a number of opencast and underground mines in the Huntly, West Coast and Southland regions in New Zealand. The company currently exports 2.1 Mtpa of coking coal. Exports are expected to grow strongly over the next five year as the company expands production into new semi-soft and thermal coal reserves. Domestic coal demand is also expected to grow strongly, particularly in the North Island, as the Maui gas field reserves diminish, and thermal coal becomes more important for electricity generation and meeting the energy needs of forest processing and other industries. Solid Energy is expanding and developing its risk management practices across all areas of the business: strategic planning û extensive use of scenario analysis and probabilistic modelling over a 20 year period; investment decisions û development and application of a rigorous six stage æProject Assessment GuidelineÆ process for all new mine developments; geological and geotechnical risk assessment techniques û use of best practice techniques including seismic surveys; financial risk management û a dynamic approach to hedging based on effects based analysis of Cash Flow at Risk analysis against preset risk tolerances; risk financing û the use of a captive insurance subsidiary, and the experiences of a small coal company seeking to obtain insurance cover on a æhardÆ international insurance market; and integrated risk management û the challenges of trying to implement a broad integrated risk management approach across the company, that supports implementation of strategic objectives as well as meeting æcompliance or legislative basedÆ risk management requirements.

Jan 1, 2003

By Chapman J, Kanchibolta S. S Poetschka N L

A field study was undertaken at Marandoo iron ore operations to investigate the effect of blasting on the lump/fines ratio. Three blasts, each in a different ore domain were monitored and the blasted ore was subsequently audited through the tr

Jan 1, 1998

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By Shibata Y, Shimizu R, Fukushima A

Kobe is divided by the Rokko Mountains, runn- ing from east to west. The southern section of Kobe is highly developed in contrast with the northern section, but big, new residential pro- jects like the Hokusetsu New Town and Hokushin New Town are steadily being developed. To handle future traffic between the two sections of the city, the double-tracked Hokushin Line, now under construction, will connect the Shin Kobe Station of the Kobe Municipal Transit (Kobe's subway system) to the Tanigami Station of the Kobe Electric Railway. The locations of Kobe city and Hokushin Line are shown in Fig.-1 and Fig.-2 respectively.

Jan 1, 1987

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005