Search Documents

By Showers JAF

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

Increasing attention is being focussed worldwide on the strategic environmental assessment of mining projects, including consideration of cumulative environmental effects. In New Zealand there is now an end in sight for inappropriate delays in resource consent approval of responsible mining projects. This paper investigates six case examples of recently consented mining and quarrying projects, whose applications were notified. It also explores the nature of delays that occurred, the factors that contributed to the delays, and whether the consent process delivered fair and effective public participation and desirable environmental outcomes.

Jan 1, 2005

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By M Ben, P de Donato, M Kongolo

The extensive literature on sulfide flotation indicates that pyrite poorly floats under alkaline condition. Xanthate concentration has a positive effect on pyrite flotation, but above a pH of 11, pyrite seems to be strongly depressed, independently of the concentration in xanthate. In this investigation, aeration and xanthate concentration effects were studied for pyrite flotation conditioned at pH 11 with lime. Results presented in this paper include surface infrared analyses and pulp chemistry measurements which have showed that aeration had a dual effect on pyrite flotation. It induced pyrite surface activation by oxygen, and oxidation of ferrous iron to ferric hydroxides or oxyhydroxides species. It also favoured dissolution of CO2, leading to calcium carbonate precipitation and adsorption onto pyrite surface. Both CO2 dissolution and ferrous oxidation generated protons and decreased pulp pH. Pyrite flotation was observed to be effective with a statistical monolayer of xanthate that could be adsorbed as mixture of dixanthogen and metal-xanthate complex. Non-floated fractions showed high amounts of carbonate, and presence of hydroxyl iron sulfate (Fen(OH)m(SO4)p, xH2O) which have inhibited the hydrophobicity effect of adsorbed xanthate. Environmental desulfurisation could be improved by aeration control causing pyrite oxidation and pH decrease to reach optimal flotation condition with a relatively low xanthate concentration.

Jan 1, 2005

By Martin JD, McNicol JH

The electrolytic zinc plant at Port Pirie South Australia, was designed and constructed to treat zinc oxide fume recovered by treatment of lead blast furnace slag in two fuming furnaces, The plant was commissioned in late 1967. The equipment installed and the oper- ating procedures adopted,'are described in some detail.

Jan 1, 1975

By Cecala AB

For 20 years the US Bureau of Mines has been researching strategies for improving the physical, social, and psychological work environment of the miner. The products of this program have shown that a consistent link exists between safety and productivity, and the key to this link is the use of effective human factors and management practices. There are specific research findings from the research projects of the Bureau on ergonomic design of mining equipment, redesign of tasks (especially materials handling) to minimize back injuries, human resource management techniques for increasing safety and productivity, and improved shift rotation schedules. Current research is continuing these themes with new applications to high technology mining systems, including computer assisted extraction devices and mine monitoring.

Jan 1, 1991

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

By J A. Brown

Osborne Mine commenced hydraulic filling of three stopes in April 1999. Two of these stopes experienced barricade failures in July 1999 and January 2000. As a result, a review of hydraulic filling was commissioned in April 2000. The design of a trial of revised specifications and practices is in the final stages, prior to the trial commencing in mid-2002.

Jan 1, 2002

SINCE writing the above-mentioned paper, some further indicator cards have been taken from the No. 1 machine, and the writers believe that a reproduction of these cards will be interesting as illustrating the performance of the machine after fifteen month steady running, night and day, seven days per week and twenty-four hours per day, at the average speed of fifty-seven revolutions per minute (see Fig. 1, page 60). For the past twelve months no adjustment have been made in the valve setting, and the only repairs have been in connection with the springs of the poppet valves, and these but slight, the springs latterly having been removed. The cards illustrated were taken with one indicator, and, therefore, are not simultaneous, andmay show to some extent the yariations of individual strokes, and with that qualification may be taken as typical of the machine's average performance.In connection with some feed-water measurements of the winding engines a rough test was run with the two compressors, the Riedler and the Corliss, coupled to the condenser, and running at fifteen and fifty-seven revolutions per minute respectively, with the result of 15.9 pounds of steam per indicated horse power per hour. This result, though only approximate, seems to indicate that the No. 1 machine is running under the guaranteed consumption, and that it is capable of maintaining this under the severe conditions of everyday practice.

Jan 1, 1909

By J P. Wyethe, D P. Padayache, B R. Green

The development of an ion exchange process for the recovery of vanadium from solutions containing low concentrations of vanadium and/or slurries is discussed. The process can be used to improve overall vanadium recovery throughout the plant, and/or to reduce the vanadium concentration of waste materials prior to their disposal. The development of the process on a laboratory and miniplant scale is discussed, and includes:selection of a suitable resin with the desired loading and elution characteristics; laboratory-scale testwork to evaluate the use of the resin in both resin-in-pulp and fixed bed configurations; recovery of a high-value vanadium product from the resin eluate; and a preliminary techno-economic assessment of the financial viability of the process.

Jan 1, 2000

Industrial relations on Australian and New Zealand resource projects can be volatile. Therefore investors have become increasingly aware over the years that sound industrial relations during construction is vital to the overall success of their project. There has been a wide range of actual industrial relations performance, project by project, and the degree. of success often directly correlates with the degree and thoroughness of pre-project planning. However, although many projects have been crippled by delays and cost overruns because of labour disputes, good results are achievable. Total commitment to the project by all parties involved is essential and it is up to the employers to seek out this commitment and not just trust mother luck. Industrial relations must be taken very seriously as the price of failure can render a resource project unviable.

Jan 1, 1983

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

Coal mining safety and health legislation is more than typical of safety legislation which has been born of adversity. Indeed, in the main it has been the child of disaster. Requirements which now appear obvious were indeed only occasioned by either social injustice or more commonly by great disasters. Even then changes were often made only after months or years of deliberation by committees. Early mining legislation in New South Wales benefited from the experience in Great Britain. The pioneers of our industry were miners from there and brought with them the basic British legislation, so we started with knowledge gained the hard way. A review of accidents statistics provides a measure of the effectiveness of mine safety legislation, but unfortunately rules cannot control human nature. Miners, managers and inspectors must work as a team to make mines safe and new legislation in New South Wales is planned to this end.

Jan 1, 1975

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

By G Muller, P Larrondo, M C. Godoy

The categories of Mineral Resources and Ore Reserves that may be used for public reporting in Australasia are defined in the current JORC Code (2004). Most internationally accepted codes emphasise the principles of transparency, materiality and competence in classifying resources. They also provide some guidance in considering the impact of data quality. There is no method recommended in the JORC Code to classify a Mineral Resource into the allowed categories of Measured, Indicated and Inferred for public reporting. A clearly defined procedure is desirable for many reasons, including consistency, repeatability and auditability. The demonstrated use of geological knowledge in the classification method is desirable. In deposits with abundant historical data there can be large variations in data type and quality. Quantification of the error of the estimates may also be considered. Ways to formally incorporate such information into the resource classification process are presented as a first step towards establishing an objective, repeatable methodology that allocates resources into appropriate categories based on defined criteria of accuracy and precision.

Jan 1, 2006

By R Dimitrakopoulos

The development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and may require the use of stochastic conditional simulation techniques. Multiple-point methods have been developed for petroleum reservoir modelling, enabling reproduction of complex geological geometries. This paper considers a multiple-point approach to capture the uncertainty of the lithological model. The implementation of the method at the Yandi channel iron ore deposit in Western Australia and performance characteristics are discussed. The uncertain lithological model translates into considerable grade-tonnage uncertainty.

Jan 1, 2007

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

The source and origins of the hydrothermal fluid of orogenic, or quartz-vein lode-gold deposits remain uncertain and disputed: Resolution would likely have a significant affect on exploration strategy. The gold-carrying fluid is interpreted to be a low-salinity mixed aqueous-carbonic fluid of near ambient pH and redox state, that may be derived either magmatically through crystallisation of granites at depth in the crust or through metamorphic reactions in a range of rock types. Classic isotope and geochemical tracers of fluid source have not differentiated these possibilities and have produced conflicting conclusions. Mass balance calculations show that fluid composition will be modified by wallrock reaction between source and deposit, and tracers should not be expected to give clear indications of fluid source. Fluid oxidation state can also be modified along flow paths. Tracers should be interpreted with care and with view to possible modification. Modelling of full flow paths and examination of the hydrothermal histories of proposed source rocks may be alternative approaches to determining fluid source.

Jan 1, 2002

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984