Search Documents

By Ibrahim AR

The experimental phosphate mine of abu Tartur has been recently placed into production. Some problems'have been encountered in maintai- ning grade control due to the differences between early block estimates and actual produ- ction grade. An area of 100 km2 is evaluated by using four methods of evaluation , namely polygonal, inverse distance , inverse distance squared and geostatistical methods. The results of calculations are compared statistically with the control values of grade and thickness. The comparison showed that the. kriging technique gave better estimations for the relative ore reserved, while for grades or thickness any of these techniques except the polygonal can be Used.

Jan 1, 1986

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By Gao K, Wu C, Xia J, Burdett M

X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques have been adopted in this study, to investigate the structure of carbonaceous materials such as graphite, brown coal char as well as coke, in order to explain their dissolution performance during ironmaking. These materials have been selected for study since they are commonly used recarburizers in the metallurgical industry. It was concluded that the crystal structure in a carbonaceous material can have a significant influence on its dissolution into iron melts. The material with the highest degree of ordering, which is graphite, showed the best dissolution performance. In contrast, the material with the lowest degree of ordering, which is brown coal char, showed the worst dissolution performance.

Jan 1, 1996

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

The combustion characteristics of Australian coals which contain high inertinite have been studied in a laboratory drop tube furnace and a Thermogravimetric Analyser. The pyrolysis chars and combustion residues were microscopically characterised using a modified coal petrography technique. Results indicated that the overall burnout of inertinite-rich Australian coals under pulverised fuel combustion conditions could be generally within a range of 97 - 99 per cent burnout. The studies showed that poor coal burnout cannot be generally related to high inertinite content in the Australian coals. The extent of coal burnout varies from coal to coal and vitrinite as well as inertinite may contribute to the unbumt chars in combustion residues. Combustion conditions had greater influence over char formation and coal burnout than the coal properties. However, under similar pf combustion conditions, coal rank and coal maceral composition had a strong influence over the coal combustion behaviours and final coal burnout. Simple correlations using coal properties may be used but with caution to determine coal volatile release and burnout at high temperature and rapid heating conditions.

Jan 1, 1991

By Cusack BL

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. This resulted in a deterioration in metallurgical performance with increased loss of lead and zinc to residues at each concentrator. Investigations to determine the cause of the problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical Deterioration.

Jan 1, 1970

Evaluation of reserves on a production scale within a shear-hosted gold deposit is complicated by the nature of the mineralisation itself. The 'payable' ground seems to be confined to areas with intense shearing, while the remainder of the deposit is characterised by 'background' mineralisation at a very low level.

Jan 1, 1993

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

SPOT imagery acquired in May 1986 of the areas that include the Dugald River lead-zinc lode, northwest Queensland, Australia and the Ngwenalekau copper deposit, Botswana has been evaluated and compared with LANDSAT MSS imagery of the same areas. The data have been processed using band combinations, band ratioing, principal components analysis and classificatory techniques and the outputs compared with those of geobotanical, geochemical and biogeochemical data as well as geological information. For both study areas the image processing techniques cited have successfully distinguished discrete vegetation associations related to discrete surficial and bedrock geological units; and, notwithstanding the sharp contrasts between the nature of the geobotanical anomalies that in both areas occur over mineralised bedrock in Proterozoic sedimentary sequences, they have successfully identified the areas of anomalous vegetation over the mineral deposits. Greater vegetational and geological detail is revealed than on outputs generated from LANDSAT MSS data [see Cole, 1977, 1982(a) and (b)]. The additional information yielded by SPOT imagery compared with LANDSAT MSS imagery results from its greater spatial resolution - 20 metres as against 79 metres - and from ti fact that the three SPOT MSS spectral bands - 0.50 0.59um, 0.615-0.68um and 0.79-0.89um - respectivelc cover those sections of the electro-magnetic spectrum in which leaf pigments, notably chlorophyll, absorption for photosynthesis and leaf cell structure strongly influence reflectance. This accords opportunities for the detection of reflectance aberrations caused by stress due to drought and/or metal toxicity as well as for the identification of anomalous vegetation communities of moderate sizr These cannot be accurately discriminated on LANDSA I MSS imagery on which only very large geobotanical anomalies like that over the Lady Annie phosphate deposit in northwest Queensland [Cole, 1977, 1984; Cole and Owen-Jones, 19771 can be detected.

Jan 1, 1988

By P Barrette

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, any tool that provides real-time feedback on the process is vital (Edwards, RP 1994). The introduction of an on-line moisture sensor would become a welcome addition to the process control field instrumentation package now applied. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the æwish listÆ of mineral processors since the problem has always been that you can only control what you can measure, (Konigsmann, 1990). Today, the task of moisture determination is still done by the classical technique of loss in weight utilising uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of seven to nine percent, but controlling the moisture content below eight percent is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from five to twelve percent before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a unique and promising novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimisation of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarise the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. The commercial model of the equipment is described with the features and benefits to the users summarised.

Jan 1, 2003

The word governing derives from gubernare meaningto pilot a ship. Being inclined to metaphors, one could be forgiven to think that politicians act this verb and captain the Nation's ship into some definite course. In the case of at least the mineral resources industry, it seems that there are not many James Cook followers in our parliaments: Australia's approach to mineral and energy policy is often chaotic - witness the 1935 to 1961 ban on iron ore export-ing which prevented the development of a significant steel industry at time when the World was hungry for this metal, just to mention one amongst many other examples.The follies of Australia's mineral policies are well il-lustrated in the case of uranium mining. Although Australia had the Western World's largest economic reserves of uranium, it is onlythefifth producing nation and its uranium potential is largely unrealised. At the root of this situation are the interventionist attitudes and policies of successive Federal Governments which for more than four decades distorted the Investment decision and, in more recent times. discouraaed investment.

Jan 1, 1990

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

By K Biegaj

The paper describes challenges the author has encountered on Australian underground gold and nickel mines over the last eight years, when recovering high-grade gold/nickel bearing mine floor material with a mobile supersucker/giant vacuum cleaner and other equipment. Whilst for a number of years the mine floor vacuuming and other mine floor clean-down technologies have been accepted/adopted and are working well in other parts of the world and on the South Australian opal mines, regrettably, they have not yet gained acceptance of mining executives and mine managers of gold and metal mines in Australia, who still elect to leave the never to be recovered gold/metal behind or to put it plainly - waste it.For reporting purposes during the mining process, the portion of gold/metal included in calculation of ore reserves prior to obtaining capital funds for their development, continues to be camouflaged in various reconciliation and call factors. This approach, ie wasting of capitally developed and already broken ore stocks should be viewed by the shareholders as totally inappropriate to say the least, especially with the current gold and other metals prices.The author attempts to provide answers as to why the technology referred to above has not yet been accepted on Australian gold and metal mines and outlines the way forward.CITATION:Biegaj, K, 2012. Why do shareholders and mining executives allow mine managers to leave behind high-grade broken ore underground?, in Proceedings Narrow Vein Mining 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox's Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005