Search Documents

On the Hauraki goldfields, within the limits of Cape Colville Peninsula, the Paheozoic rocks are confined to the district north of a line drawn from Mercury Bay on the east coast to Rocky Point on the shore of the Frith of Thames. South of Kennedy's Bay they are developed on the east coast only at Kuaotunu, at which place gold mining is carried on in sandstones and slates of this age. Between Tapu Creek and Coromandel there is, along and adjacent to the shore of the gulf, a very considerable development of PaJreozoic and in part of Trias rocks, and between the Tiki Stream and the northern end of Tokatea Hill, along the western slope of the main range, lies the special area of the Palreozoic or carboniferous rocks that have more particularly to be dealt with in this paper. The same formation has a large devolpment between Cabbage Bay and the northern slopes of Moehau, and appears to the water marge on both sides of this part of the peninsula.In this part they are of special interest as having, on the west spur of Moehau, a considerable variety of dyke rocks intruded into the sedimentaries, the interest in which is increased by the fact that these dykes theIllselves are of Palreozoic age and correspond to the dykes that are so' abundant in the Tokatea-Tiki area. It is this Tokatea-Tiki area as a goldfield, and its rocks as distinguished from later volcanic' products' on other parts 'of the peninsula...

Jan 1, 1903

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

The recent paper by Bain (1981) contains an unfortunate, and potentially misleading typographic error. On page 9, second paragraph, Bain states that, "some samples of drill core from the (Candlow) Formation ... contain up to 90 ppm gold and 2 000 ppm arsenic". The gold value should read 90 ppb. In fact, in the original version of the paper (Bain, 1980), the gold value quoted was actually 60 ppb.Bain also refers briefly to some geochemical data which is attributed to me, and which I feel require some clarification.In addition, the paper contains some factual errors relating to the occurrence of carbonate and potential host rocks to Carlin-type gold deposits in the Candlow Formation.

Jan 1, 1981

The history of the industry which recovers rutile and zircon from the heavy mineral beach sand deposits of Eastern Australia began with the initial discovery of zircon in 1895. Whereas a large number of small companies operated during the rutile boom of 1955-57, the industry is now controlled by a few large groups.Mining is mainly by suction dredging. Metallurgical practice is a two-stage process in which a bulk concentrate of heavy minerals, recovered by gravity methods, is separated into its constituent minerals by processes based mainly on surface, electrical, and magnetic properties.Various separating devices using these principles have been developed in the industry and combined in various ways in the operating plants.There is scope for future metallurgical developments.INTRODUCTIONThe existence of deposits of heavy minerals ("black sands") on the northern coast of New South Wales has been known for at least 90 years. The earliest metallurgical operations aimed at the recovery of gold, platinum, tin and monazite. Mainly because of the low grade of these deposits with respect to these minerals, but also due to metallurgical difficulties, such operations were abandoned by about 1895 (Whitworth, 1959). The presence of zircon was recorded quite early (Carne, 1895) but Raggatt (1925) appears to have been the first to report the presence of rutile.The economic exploitation of the deposits was initiated in 1928 when D. H. Newland, State Geologist of New York, made an examination on behalf of The Titanium Alloy Manufacturing Company of America. Developments were then delayed by the world-wide depression, and the first commercial separation of the heavy minerals was made at Byron Bay in 1934 by Zircon Rutile Ltd. using a froth...

Jan 1, 1963

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By B Mead, N D. Pascoe

The Grasberg block cave rail haulage system will be located in the Grasberg mining district on the island of Papua, Indonesia at an elevation of almost 3000 m above sea level. It will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing systems. The design entails approximately 23 km of rail (ballasted and embedded track), over 120 ore chutes to deliver ore to the muck cars and three unloading stations to deliver ore to the crushers. The rail haulage system is a closed-loop system entirely within the underground mining complex.The GBC rail haulage project will be a substantial operation. Trains consist of 11–12 bottom-dump 20 m3 muck cars driven by a 40 t electric locomotive, about 400 t per trainload. Approximately 12 trains and one spare are required to maintain full production at 160 000 t/d. All rail installations will be 1435 mm (standard) gauge with AS60 steel.The rail system is designed to operate in full automated mode, including chute loading, hauling and dumping. The operation will be controlled from a surface control room.The rail haulage project has been divided into five stages, which will be brought online over the course of ten years. Current development and construction are focused on Stage 1 for initial production that will occur beginning in late 2017. This stage includes 24 chutes in three chute galleries, one unloading station, workshop areas and almost 7 km of track (3 km of embedded and 4 km of ballast).This paper describes the key components of the rail haulage system and reports on the current status of development and construction of the system. This paper also overviews the challenges, successes, issues and risks of this project in areas such as scheduling, development, construction and operation.CITATION:Pascoe, N D, Mead, B and Vega, H, 2016. Grasberg block cave haulage project – design and construction update, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 585–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912

The following paper deals with a method for the" Proximate Analysis" of Chloridized Ores, which are free from arsenic, antimony and lime. When these are present the analysis is rendered far more complicated, and many of the methods which I am about to describe could not be applied. Sufficient scope is therefore offered for discussing the analysis, when these metals are present, in a separate paper, which I hope to contribute at a future date.I am fully aware that this method is far from being perfect. No doubt many, modifications and improvements will suggest themselves to my readers, and I trust that this paper will be the means of giving a certain impetus to the study of Proximate Analysis which at the present time is practically dormant. For the benefit of my readers who are not initiated into the details of ordinary estimations, I have briefly described well known methods, which, however, will be found fully described in most text-books of analysis. Assuming that the ore contains. sulphates and chlorides of soda and magnesia, sulphates, sulphides, chlorides and oxides of copper, lead, iron, zinc, manganese and silver chloride, the analysis would be conducted as follows. The first compounds to estimate are the chlorides and sulphates of soda and magnesia.

Jan 1, 1901

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.Low-sulfidation epithermal gold mineralisation at Ridge Mountain occurs within the Oligocene to Miocene volcanic rocks comprising andesite, porphyritic dacite and diatreme breccia. A diatreme breccia complex with a NE–SW elongated orientation covers an area of 3.0 × 1.7 km. Four main stages of mineralisation were identified, comprising: E–W- to NW–SE-trending quartz-chalcedony veins with disseminated pyrite, chalcopyrite and gold. N–S- to NNE–SSW-trending breccia veins with quartz matrix and disseminated pyrite and accessory sphalerite, galena, chalcopyrite and gold. NE–SW-trending quartz and calcite veins with disseminated pyrite and accessory sphalerite, galena, chalcopyrite and gold. ESE–WNW- to ENE–WSW-trending quartz veins with disseminated pyrite. This stage is only mineralisation that is hosted by diatreme breccia and clearly postdates.Quartz veins of the first, third and fourth stage are less than 2 m wide. Only breccia veins of the second stage are up to 10 m wide. Gold is present in all stages as microscopic inclusions in quartz and sporadically in pyrite. Macroscopic gold can be seen in the first and second mineralisation stages. Gold commonly occurs in association with sphalerite, galena and chalcopyrite in the second and third mineralisation stages.CITATION:Kucera, J, 2015. Diatreme breccia-hosted epithermal gold deposit at Ridge Mountain, eastern Mindanao, Philippines, in Proceedings PACRIM 2015 Congress, pp 587–592 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The mineral matter has been isolated from a selection of Australian bituminous coals using low temperature (radio-frequency) oxidation or hydrogen peroxidation techniques and the species present identified by x-raydiffraction. Quartz, kaolinite, and a range of mixed layer clay minerals are the dominant constituents of the coals studied, with carbonate, sulphate, and phosphate minerals abundant in some samples. The clay bands thatoccur within these coal seams contain similar mineral assemblages to the coals themselves, but the lutites that form the inter-seam strata have a markedly different mineralogy, characterized by abundant quartz andillite and a low kaolinite content.The kaolinite is thought to have formed chiefly by interaction of silica and alumina in the waters of the coal swamp, aided by the catalytic action of organic acids, while most of the other clay minerals are probablydetrital. The absence of illite from Australian coals is not fully understood, but it may reflect the action of organic acids on the detritus in the swamp, coupled with deposition in freshwater rather thanmarine conditions. Pyrite, although present in some coal samples when fresh, may undergo oxidation during storage to form a number of sulphate minerals, some of which may interact with any calcite present toform gypsum.The mineral matter assemblage in the coal determines to a great extent the fusion characteristics of the ash.Unless abundant carbonates are present, coals with kaolinite-rich assemblages have a very refractory ash, while those rich in chlorite or montmorillonite have ash fusion temperatures between 1000 and 1300°C. Theinfluence of the minerals on coal preparation and coking properties is also brieflY discussed, as well as the potential of mineral matter studies in coal seam correlation.

Jan 1, 1978

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

In formulating its strategic plan in 1998 the New Zealand Minerals Industry identified two related critical issues facing it. These are, broadly speaking, the issues of access to minerals; and the perception the public has towards the industry and its behaviour towards the environment. This presentation will report on the Industry's response to the public perception issue. The Industry has, through the NZMIA Council, and its Communication and Website Committees, developed and implemented strategies covering: communication through the print media, and through its website www.minerals.co.nz, a long-term educational outreach programme with schools, focussing on the significance of minerals, their contribution to community wellbeing and the negligible long-term environmental effects of the Industry's activities.

Jan 1, 2000

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964