Search Documents

By Stanojevic R, McGlinn PJ, Day RA, Levins DM

This paper reports the results of a number of studies that Ansto has carried out for mineral sands companies concerned about low-levels of naturally-occurring radioactivity in their products. Where measured levels of radioactivity have exceeded allowable levels, Ansto has used specialised techniques to identify the source and distribution of the radioactivity and investigated processing strategies to remove the Contamination.

Jan 1, 1993

Since the earliest recorded prospecting of the 1860's mineral exploration and mining in Fiordland has been discouraged by the formidable physical difficulties presented by its isolation, extremely rugged relief, treacherous coastal waters and generally unfavourable weather conditions. Government assistance was often sought by the miners and prospectors but little, if any, support or encouragement was received after the initial period. During the 1840's decorative marble was quarried at Caswell and Dusky Sounds. A prospector discovered and attempted to mine copper sulphides to the north of Dusky Sound (Parks Mineral Beds) and near Mt Solitary. A small Pb, Zn, Cu, Ag, Au bearing quartz reef was discovered and driven on in the granite coast line of Preservation Inlet (Bradshaws Reef) and the ore roasted on site. Alluvial and quartz lode gold was discovered at Preservation Inlet in the 1890's and led to the recorded recovery of 11 000 oz of mainly lode gold. Falloff in grades with depth, thinning and splitting of the reefs and the high mining costs at this location led to a virtual abandonment of the field by 1906. In the late 1950's and early 1960's the geology of Fiordland was mapped by the Geological Survey at 1:250 000 scale, but field work was largely confined to the shore lines of the coast and fiords. In view of the physical difficulties it is not surprising that mineral exploration and mining up to 1970 was limited to the scant attention outlined above.

Jan 1, 1977

By D Walker, A Tsvetkov, P Voigt, O Kloiber-Deane

The GPM Gold Operation has been employing an Albion Process™ plant at its Sotk (Zod) gold mine in Armenia since 2014. Long term data from the operation is now being published for the first time. The data presented includes concentrate throughput, as feed to the Albion Process™ plant (tonnes per day), sulphur grade in concentrate (% S), total sulphide sulphur oxidation in the Albion Process™ plant (% SOx) and gold recovery from Albion Process™ plant residues (%). The data provides a basis for evaluation of the effectiveness of the commissioning, ramp up and operation of the Albion Process™ plant. Notwithstanding the impact of a slower concentrator commissioning than expected, the plant demonstrates Series 1 behaviour on McNulty ramp up curves, indicating successful commissioning and fast ramp up. Interrogation of the data and operational experience indicates that this successful operation is a result of a process that is flexible, robust and stable, one that was designed well based on solid testwork results and pilot plant trials during the study phase undertaken by Glencore Technology and Core Resources, and where the local operators were provided with appropriate training in operation of the plant. CITATION:Voigt, P, Walker, D, Kloiber-Deane, O and Tsvetkov, A, 2018. Ramp-up and long-term performance of the Albion Process™ plant at GeoProMining Gold Armenia, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 339–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

By K Barbosa, G Wilkie, F Reyes, V Jokovic, C Evans

The idea behind Grade Engineering is to exploit the natural heterogeneity of an orebody (spatial, temporal) in order to divert low-value waste out of the mining value chain. Essentially, this involves rejecting material at relatively coarse particle sizes (10 mm to 200 mm). However, lack of knowledge about the inherent particle grade distributions in these coarse particle size ranges limits the opportunities for optimisation. Particle grade distributions are essential for quantifying and modelling gangue liberation and yield curves. These curves can then be used to predict the mass and value flows that will go towards the accept and the reject streams. Particle grade distribution information for particles coarser than 10 mm can be collected based on chemical assays of sufficient number of individual particles. However, for smaller particles (1 mm to 9 mm), a significantly larger number of particles is required for assays. Moreover, in some cases, the mass of individual particles is smaller than the minimum mass required for chemical assaying. Also, other quantification techniques such as automated mineralogy, eg Mineral Liberation Analysis (MLA), require extended measurement times to analyse statistically representative numbers of particles at these size ranges. This work investigates the use of 3D X-ray microtomography to fill this quantification gap at these size ranges (1 mm to 9 mm). In-house image processing algorithms are used to estimate the mineral/metal content in each particle. Particle grade distributions, as well as density distributions, are thus produced without a minimum mass requirement and with each scan providing information about tens to hundreds of particles at a time. Mineralogical data from MLA analysis, of finer size ranges, is used to inform X-ray microtomography, so a simpler 3D mineral map can be obtained using the image intensity. Chemical assay information of the scanned samples is used to validate and correct the mineral phase segmentation.

Aug 24, 2022

By S L. Nicol, B J. Hogg, O J. Mendoza, S Nikolic, A Burrows

The top submerged lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. The key advantage the ISASMELT™ TSL technology provided was the ability to process feed materials in a highly turbulent bath, reaching close to equilibrium conditions, uniquely allowing for operation below the liquidus of the molten slag phase. The details on what happened below the liquidus line in the phase diagram became critical for the successful operation of the technology. During the development of the ISASMELT™ technology this led to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore Technology, and the Pyrometallurgy Research Centre (PYROSEARCH) at The University of Queensland. The fusion of the phase equilibria research into the technology development allowed for understanding of the behaviour of molten splash, reliable tapping of the furnace, and the ability to operate the furnace with a refractory lining and achieve a year campaign life in excess of four years. The outcome has allowed for the highly successful adaption of the ISASMELT™ technology to recycling of complex feed streams necessary to drive circularity in our modern global economy.

Aug 21, 2024

By Ormsby W. R, Farrar L

The stratigraphy of the central Pine Creek Geosyncline has been simplified into a three-fold subdivision comprising the Batchelor, Frances Creek and Finniss River Groups. The Batchelor Group consists of a sequence of shallow water coarse clastics and crystalline carbonates and is conformably overlain by the marine carbonaceous shale dominated Frances Creek Group. Interbedded within the carbonaceous shale are turbidites, iron formation, tuffs, carbonate and non carbonaceous shale. The Finniss River Group is a flysch sequence of greywacke and mudstone. The stratigraphic and structural evolution and igneous history are all interrelated. Although the Batchelor Group may have formed in a tensional regime, it is likely that regional compression and accompanying thin skinned deformation began during deposition of the Frances Creek Group. Continued compression resulted in D2 folding d6collement deformation, wrench faulting in compressional zones and thrust faulting. Occasional relaxation of compression is marked by a number of periods of basic intrusion and perhaps distal volcanism. The style of deformation within sediments varies away from granitic basement highs and is similar to that observed around salt domes and found in experimental diapiric models. Sedimentary facies changes also indicate local emergence of basement highs during sedimentation. As compression continued, the deposition of thick sequences of the Finniss River and El Sherana Groups brought about regional metamorphism. Relaxation of compression and waning of associated subsidence resulted in a relative increase in the rate of uplift and partial melting of diapiric sialic basement. In places, granitic magma moved upwards and crystallised forming grossly concordant bodies. Other masses moved laterally and formed extensive granitic sills. Later compression periods caused mainly brittle deformation which may have been strongly influenced by underlying basement fabric.

Jan 1, 1994

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By D M. Silva, J C. Alves

According to the literature, material transportation represents 50 per cent of the operating costs for an open pit mine. In this context, this paper proposes a multistage approach for dynamic truck dispatching in real open pit mine environments, implemented in the commercial package SmartMine®, marketed by Devex SA. The first stage of this approach defines the optimal number of trucks that maximises the tonnage production by means of a robust linear programming model, which considers the operational constraints of a real mining process. The second stage uses a dynamic dispatching heuristic joining computational simulation and multicriterion optimisation techniques for decision making for truck dispatching. Another relevant contribution of this work is the publication of realistic instances collected from a dispatching system managing an iron mine, containing information about the hauling and loading fleet, the equipment situation when the working shift starts, cycle times, the time line of special occurrences (such as equipment stoppages and loading equipment reallocation in order to satisfy the mine planning) and the tonnage produced. These instances were generated with the purpose of submitting the method to the test of a real situation that considers the uncertainties existing in the process studied. The proposed approach was validated by means of a discrete event simulation model applied to the previously designated instances. Using this multistage approach as a mechanism for dispatch decision making, it is shown that the haulage fleet productivity increased when compared with the real values reported from the instances. These results are important because they show that the proposed approach generates efficient dispatch decisions for trucks operating in a real environment, reducing operating costs, increasing production and making the mine more competitive.

Sep 26, 2011

By C Taylor, E Retz

Sequential Gaussian conditional simulation of wide-spaced exploration data has been completed in order to optimise a drilling grid at Fortescue’s Eliwana deposit. The aim of this drill grid is to improve the confidence in the Inferred Mineral Resource. A mineralised domain within the Joffre Member of the Brockman Iron Formation was selected to be tested as it makes up a large proportion of the Inferred Mineral Resource and is drilled at a reasonable spacing.One hundred realisations of Fe, SiO2 and Al2O3 grades were completed in the domain. Three realisations were selected for each analyte to represent the range of equiprobable values and a further realisation was selected to represent the truth data set. These realisations were used to flag theoretical drill holes on varying spacings and patterns. The theoretical drill holes were used to estimate into block models using ordinary kriging.These estimates were analysed and the accuracy and precision of each drill spacing was assessed. It was concluded that the greatest improvement in estimation results was noted at either a 100 m × 50 m or 50 m × 50 m spacing.CITATION:Taylor, C and Retz, E, 2015. How much do we need to drill?, in Proceedings Iron Ore 2015, pp 491–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N M. Rana, A Take, N Ghahramani, S McDougall, S G. Evans

A critical issue associated with mining operations has been the stability of tailings impoundments. Some breach events have produced catastrophic tailings flows that have caused significant economic damage, mass casualties and long-lasting environmental impact in the downstream environment. This paper reports independently estimated values of runout distance, inundation area and fahrboschung of 16 tailings flows. The adopted methodology involves the geospatial analysis of satellite and aerial imagery to classify each tailings flow into a primary impact zone (Zone 1: main overland flow) and a secondary impact zone (Zone 2: along-creek diluted flow) to characterise runout. Only Zone 1 runout values are reported herein given the greater significance in relation to downstream impact. The fahrboschung is calculated using elevation data from global 30 m digital elevation models (DEMs) and source literature. The results show that all the selected tailings flows travelled long distances (2.4 km to 98.5 km) and inundated large areas (0.35 km2 to 27.0 km2) over very low fahrboschung values (0.04° to 4.8°). This indicates very high flow mobility that is largely governed by the high water content sourced from interstitial waters and, in many cases, supernatant ponds. Scatter plots display poor correlations owing to the complexity and variability in travel path characteristics (confinement, slope angle and obstructions) and the inherent properties of the flowing mass. The slope angle of the travel path exerts a strong control over the flow velocity which has implications on kinetic energy and downstream geomorphological impact. Mean tailings flow velocities may range from ~6 m/s on near-flat, open terrain to over 30 m/s in relatively steeper, channelised travel paths, indicating that tailings flows fall within the extremely rapid and high mobility spectrum of global mass movements. The presented work forms an inceptive part of the CanBreach tailings project, a major component of which is to develop a comprehensive database of case histories to examine the role of geotechnics, failure modes and downstream terrains in influencing tailings flow behaviour.

Jul 1, 2021

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By X Li, J Wang, D Liu, Y Liu, K Hu

"Since the adoption of open-door policy 30 years ago, rapid economic growth has resulted in serious resource depletion and environmental destruction, especially in mining areas. As an urgent response to this situation, the central government and the Ministry of Land and Resources (MLR) have adjusted policies with concrete and realistic actions for halting this trend of non-sustainable mining activities in China. æGreen Mine CampaignÆ is one of the actions implemented. In 2010, MLR announced the æGreen Mine CampaignÆ, in which existing and new mines will be evaluated against the æGreen Mine Construction StandardsÆ and certified as æGreen MineÆ if complying with these standards. The standards cover five key aspects: the considerations of science-supported resource exploitation efficient resource utilisation standardised management environmental friendliness harmonious community relationship.Every year, MLR reviews ægreen minesÆ from all provinces. Thirty seven mines, including coal, metal, non-metal, gold, chemical industry and building materials mines, passed the review and were certified as green mines in 2010. In 2011, 187 out of 194 mines that participated in the review were certified as ægreen minesÆ. These mines are viewed as good examples of sustainable mining development in China.CITATION:Liu, Y, Hu, K, Li, X, Liu, Y, Liu, D and Wang, J, 2012. The green mine campaign and sustainable mining in China, in Proceedings Life-of-Mine 2012, pp 339-342 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By J Player, P Evans, G Sweby

Achieving quick underground access after the completion of an open pit mine can be critical to maintaining project value and ensuring regular ore feed to the mill. This paper outlines the design and construction for two portals in an active open pit to commence underground development quickly whilst installing appropriate ground control to maintain long term access in an uncertain setting. Implementation of the portal designs was complicated by the change in underground design from hangingwall access to footwall access late in the life of the open pit due to preferable ground conditions. The portal locations did not have easy access for ground support installation integrated into the pit design due to the timing of the underground design changes. Practical implementation of the ground support systems subsequently became a key part of the project. Intact rock strength, rock mass characteristics, gradational weathering / alteration profile and structural information were modelled against pit displacement monitoring as the basis from which the portals were located and ground support schemes designed. Conditions around one of the portals necessitated numerical modelling to estimate the appropriate level of ground control for long term stability. The design was completed whilst the open pit was actively on-going and the portal areas not entirely exposed. The rock mass assessment and analysis for the two portals indicated different ground support scheme capacities would be required. The expected level of control for one of the portals also necessitated the use of monitoring with extensometers and load cells to ensure the rock mass response and ground support scheme performed as planned. Construction of the portals demonstrates the benefit of a considered design process, a plan which allows practical installation of ground support schemes where access is limited, the benefit of ongoing monitoring to ensure performance remains within design limits and the challenges involved working within an active pit with limited floor space.

Mar 15, 2021

By G Chitombo, A Perryman, A D. Campbell, J White, B Hollis

This paper describes the development and implementation of an optimisation tool developed as part of the Mass Mining Technology (MMT) Project. The tool, known as the SLC Schedule Optimiser, is capable of optimising the schedule of development and production activity for a sublevel cave, given a fixed draw strategy, for the life of the mine.This paper starts by describing the development and production scheduling problem for a sublevel cave, the geotechnical constraint that a schedule of activities must adhere to, and outlines the pre-existing manual planning procedures used to produce schedules.Following this, the paper then outlines the optimisation tool developed, describes the changes to the planning process it has enabled and finally quantifies the improvement to operations this tool has brought using Glencore’s Ernest Henry Mining Operations as a case study.CITATION:White, J, Perryman, A, Campbell, A D, Hollis, B and Chitombo, G, 2016. Life-of-mine development and production scheduling optimisation for sublevel cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 133–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By J Dyt, S Lyons

In the mining industry, crusher-related incidents have led to 15 reported deaths in Australia, New Zealand, and the USA between 1998 and 2007 (NSW Government Resources Regulator, 2024). The majority of these fatalities occurred during routine crusher maintenance tasks. A survey of quarry and mine site maintenance staff was completed to ascertain what they thought of such safety device to understand if beneficial and if so reasons if unused. Overall, findings show, staff perceived risks differently, cost, familiarity, device awareness and not front of mind, influenced adoption. This underscores the importance of asking the right questions involving maintenance and safety staff to lead to more proactive risk assessment.

Apr 16, 2024

By Y S. Zhang

Natural phenomena and human engineering construction activities had great influence on the geosciences space. Natural disasters, particularly mine disaster and other geological disasters happened frequently, which brought great losses both in people’s lives and economics, therefore, to explore the essential causes and mechanisms of disaster by some useful approaches is the most important step in mine disaster prevention. In a variety of methods, building an aground-underground seamlessly integrated model, and then analysing the formation and development mechanism of mining disaster based on this model is a useful way. In this paper, we studied an aground-underground seamlessly Integrated modelling method, and correspondingly given an aground-underground seamlessly integrated 3D spatial model, CSG+CD-TIN+GTP-TTS, by which we can carry out analysis of surface subsidence and underground laneway distortion efficiently, finally preliminary applications verified the effectiveness of this method.

Nov 22, 2011

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022