Search Documents

By M Doran

The Olympic Dam mine utilises 1.1 m to 1.4 m diameter raise bores for generating the initial slot void for most production stopes. Slot raise bores generally span two development levels ranging from 30 m to 50 m in height. Raise bores are reamed upward and typically leave a cap of rock equivalent to two times the raise bore diameter on the drill level (minimum 3 m). This provides safe access over the cap for subsequent production activities. It is therefore critical to ensure robust falling object protection for personnel accessing underneath, and in the vicinity of the raise bore void on the lower level. Recently, a number of mesh failures have occurred at Olympic Dam as a result of falling rock from the underside of the cap and raise walls. In addition, as Olympic Dam transitions to deeper and more challenging ground conditions, rockfall-off onto the raise bore protection mesh is anticipated to increase in frequency. This paper discusses the evolution of raise bore protection mesh used at Olympic Dam and presents results from recent site-based drop testing. This impact testing was carried out using a built for purpose object to replicate point loading and shear failure of mesh wires. Testing was also carried out on an improved mesh design which utilises two layers of Geobrugg high-tensile MINAX mesh. Results from the drop testing suggest an improvement in performance of the raise bore protection mesh is realised with the updated design.

Mar 29, 2023

By Gregg PEH, Stewart RB

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed. After seven years, the rate of increase of N, C, P and S, losses of S and P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site.

Jan 1, 1995

By D Cumming-Potvin

Incidents that trap miners in underground mines have serious consequences for the miners and the mine operators involved. It is of utmost importance that mine operators utilise all available tools when trying to locate and rescue trapped miners. From testing conducted at underground hard rock mines, Cumming-Potvin et al (2013) found that pre-existing microseismic monitoring systems, which are routinely used for seismic risk management, have the potential to be used for detecting and locating trapped miners.This paper reflects on the Anzac Day seismic event that trapped two miners at Tasmania Mine, Beaconsfield, on 25 April 2006. The Anzac Day event occurred at 2123 on a Tuesday evening. Rescuers were unable to confirm that the trapped miners had survived until 1930 on Sunday evening. It is not possible to speculate on how the rescue operation may have been different had the technology to use the microseismic monitoring system for the purpose of detecting the trapped miners been available. However, it almost certainly would have been different. The recent research project has demonstrated that knowing the fate of the Beaconsfield miners might have been achievable up to 100 hours earlier than was the case in 2006. That knowledge would have been invaluable to the rescue effort.By examining the seismic array at the Tasmania Mine, the reliability of detection over the working levels of the mine could be quantified. Had the methodology been available, adding six additional sensors (at a cost of $40 000), would have been sufficient to increase the likelihood of detection to greater than 90 per cent in the working levels of the mine. This was true both at the time of closure of the mine in 2012, and just prior to the Anzac day event.CITATION:Cumming-Potvin, D and Hills, P B, 2014. Use of a pre-existing microseismic monitoring system to detect trapped miners (with reflections on Beaconsfield 2006), in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Polthier K

A short discussion of the salient aspects of a dispersed flow model in relation to the gas flow in blast furnaces is given. The use of the theory in assessing vessel performance is mentioned. Tracer results of a blast furnace (688 m3) from three furnace levels and different radial positions are analysed and results presented as D/ud values. The significance of the shapes of experimental tracer curves are included and comparison is made with results obtained on other furnaces.

Jan 1, 1975

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Francoeur

Oct 12, 2022

By C J. Moran

The Gladstone region, as one of the most industrially intense regions in Australia, uses significant quantities of fresh water. Awoonga Dam, situated on the Boyne River, is the only major source of water in the region. The current typical annual usage is 53 GL (Porteous, 2006) and approximately 80 per cent of the water is used by heavy industry (Gladstone Area Water Board, 2004). Until relatively recently, there has been ready and easy access to raw water for industrial use. The recent drought, which resulted in severe water restrictions in 2002 and 2003, emphasised the importance of water for a dominant industrial region like Gladstone. Although now in the process of changing, the typical contractual arrangements in the past have provided little financial incentive for efficient water use. From research undertaken on potential water reuse opportunities, several key questions have emerged related to water management in an industrial region such as Gladstone. This paper highlights these key questions, presents findings from recent regional strategies and assesses the potential for water reuse. Even though there is no clear-cut financial incentive for reusing water, there could be stronger regional and risk mitigation drivers for doing so. Initiatives to incorporate adaptive capacity through collaborative industrial synergies would allow for robustness and resilience in water security, leading to long-term sustainable water management across the Gladstone region.

Jan 1, 2006

By R R. J McAllister, K Moffat, S Heyenga

This paper examines the statistical relationship between quality of life indicators and the gross value of mineral production from Australian regions. We used quality of life indicators, aggregated for 673 local government areas, of household income, housing affordability, access to communication services, educational attainment, life expectancy and unemployment. We find no evidence of systematic negative associations between quality of life and the gross value of minerals production. Instead, mining activity has a positive impact on incomes, housing affordability and communication access across regional and remote Australia. Whilst we do not establish causality between mining activity and quality of life, our analysis prompts a rethink of the æresource curseÆ as it applies within a single country. Nevertheless, our findings are tempered by extensive anecdotal and empirical evidence of the negative social impacts of mining on specific demographic sectors, localities, families of fly-in, fly-out mining operations and individuals. This contrast may be a scale issue, with the regional benefits of mineral wealth masking highly-localised inequalities and disadvantage. We suggest that there is a need to better understand these impacts and, more importantly, the types of policy mechanisms government and industry can adopt to mitigate or avoid them.

Jan 1, 2009

This paper has been developed for æThe Race for SpaceÆ conference. It ranges over various aspects, all of which are within the umbrella of marketing. The question is posed because many engineers, tunnelling and other specialisations, frequently demonstrate an unwillingness to embrace marketing. The accurate reply is probably à ænot an engineer!Æ The paper identifies some of the possible explanations for this reply. The vast majority of the themes, ideas and principles are based on more than 25 years actual experience for the author with Engineers, Tunnelling and other disciplines. This experience has been gained with leading consulting engineering practices; some of the worldÆs largest construction contractors together with other organisations employing engineers in the public, private and tertiary sectors in the UK; US; Europe; the Middle East and throughout Australia and New Zealand. Experience has been gained in design offices; head offices and construction job sites in four contrasting continents. The most significant themes developed throughout this paper are as follows:æLetÆs go and do some ærealÆ work and leave the marketing to others!ÆæMarketing is just a æsoftÆ option and neither technically based nor true management!ÆNIMBY-ism (Not In My Back Yard) so leave well alone!Engineers regularly confuse services marketing -v- product marketing à a useful cop out, or a genuine cry for help?Marketing databasesæLetÆs get rid of the term æsellingÆ and replace it with the more acceptable à and less distracting for tunnelling engineers à 'marketingÆDistinction between benefits and features à in The Race for SpaceSales Comprehension Test, Benchmarking TestJack WelshÆs æmost difficult decision for a CEOÆHarvard Business ReviewÆs (HBRÆs) formula for performanceMany engineers are losing the balance in their lives Sustainable development and engineering æQuality work doesnÆt mean quality serviceÆMajor recommendationsRecommended references

Jan 1, 1999

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By N Ozawa, R Kaneko, M Arimit

The Mitsubishi Higashitani limestone mine is a ten million tonne per annum operation located near the city of Kitakyushu on JapanÆs western island of Kyushu. Higashitani is one of the largest limestone mines in Japan and accounts for about five per cent of national production. Blasting practices at the Higashitani mine involve the use of bagged ANFO, dynamite primers and non-electric detonators. Regulations in Japan prohibit the use of site mixed bulk explosives. Blast size is usually around 17 000 tonnes with 20 holes in a single row, two or three blasts are fired per day at a powder factor of between 0.25 and 0.32 kg/m3. As part of a program looking at oversize reduction Mitsubishi, Asahi and Orica agreed to conduct a joint project at the Higashitani mine to investigate the relationship between the powder factor and fragmentation. The first stage of the project was to benchmark the current blasting performance. Five blasts were monitored in each of the 210 (hard rock) and 220 (soft rock) areas of the mine. OricaÆs Powersieve« software was used to measure fragmentation and total rock breaker hours were also recorded for each blast. OricaÆs computer blasting simulation model Sabrex« was used to prepare revised blast designs with a higher powder factor and predict their performance. The performance of these blasts was monitored using the same methods.

Jan 1, 2004

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

The Koongarra uranium deposit was discovered in August 1970 by Noranda Australia Limited. Denison Mines Limited acquired the rights of ownership in October 1980 and has continued the 'struggle' to bring the proposed mine, containing approximately 13 300 tonnes of U308 of Indicated ore and having a value of $1 billion (1984 dollars), into operation. During the 14 years that have passed, the owners have found it necessary to deal with numerous Federal, State and Territory government departments, aboriginal representatives, handle thousands of communications, attend and convene countless meetings and spend millions of dollars. This paper addresses the history, the requirements, the problems and the costs to date for what - no return.

Jan 1, 1984

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

Through partnering with mining customers, DYNO has been able to develop some specific technologies that benefit blasting operations particularly in underground mining. Some of these areas are: 1. Cost allocation and product tracking systems; 2. Borehole video surveys of breakthrough blastholes; 3. Borehole video photography for logging VRM blastholes; 4. Toe-load uphole loading for sublevel cave mining operations; 5. 3D blast modelling for underground ring blasting. This paper outlines these developments in the context of a Canadian underground metalliferous mine.

Jan 1, 1995

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The paper describes data from test work programs on a range of magnetite ores in Australia and overseas. The analysis looks at the behaviour of material of different sizes fed to the rolls and the change in product size as a result of that, the conclusion being that there is a logarithmic relationship. The paper develops a form of equation to predict the product size from a given feed size distribution. The behaviour of the various magnetite ores is compared to more standard test methods such as crushing work index and unconfined compressive strength.

Jan 1, 2009