Search Documents

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By M G. Shaw, M A. Rhamdhani, S P. Singh, A R. Duffy, B Eisenbart, A K. Shukla, G A. Brooks

The field of astrometallurgy is a growing area of study. Metal production on the Moon is likely to begin in less than a decade as major space agencies such as NASA (National Aeronautics and Space Administration) and CNSA (China National Space Administration) are preparing to construct permanent lunar bases. The utilisation of regolith to generate oxygen and metals is expected to be important in the development of a sustainable lunar habitat. This paper provides an overview of potential metallurgical processing methods for lunar conditions, emphasising the impact of lunar factors on slag chemistry. The interaction between regolith and the extracted metals, as well as their impact on slag composition and refractory performance, are critical considerations in metal production on the lunar surface. The initial research on lunar metallurgical technologies is focused on oxygen extraction and Fe-Si alloys are reported as the by-products of these processes. This paper delves into the fundamental thermodynamics associated with the carbothermic reduction of lunar regolith. Thermodynamic analysis using the FactSage™ ver 8.2 software package indicates that the Fe-Si alloy can be produced as a metallic product from the lunar regolith at temperatures ranging from 1400°C to 1600°C under terrestrial conditions. However, under ultra-high vacuum conditions (3 × 10-15 bar) on the Moon, the required operating temperature for producing ferrosilicon would be significantly reduced. Thermodynamic modelling results indicate that under lunar vacuum conditions, Fe-Si alloys only exist as solid phases at lower temperatures below 650°C. At higher temperatures, both Fe and Si are expected to be present in the gas phase. In this work, the carbothermic reduction of the Lunar Mare Simulant (LMS-1) is conducted under terrestrial conditions. The findings indicate that the process can readily yield Fe-Si alloys with 7–10 wt per cent Si at 1600°C. Additionally, energy dispersive spectroscopy (EDS) analysis of the resulting Fe-Si alloy indicates the presence of phosphorus up to 1 wt per cent.

Aug 21, 2024

By P Carrasco, E Me, M Campos, J Tapia

Correct sampling practices are of vital importance to the mining industry; key decisions for the business are made on the basis of samples in all the value chain. Geology plays a relevant role in pre- and post-investment stages. Actually the understanding of natural variability is essential for geological modelling, geometallurgical modelling, mine planning, grade and process control. Improper sampling practices obstruct this objective introducing irrelevant variability components, which can cause monumental economic losses. A good approach to accomplish this understanding is the application of heterogeneity and IngamellsÆs tests, which are useful tools to quantify the variability of a certain well-delimited geological unit at different comminution scales. The application of heterogeneity test can help minimise Pierre GyÆs fundamental sampling error and to study the impact of other sampling errors. IngamellÆs test allows us to define the correct mass of sample for chemical analysis. This paper presents the results of several heterogeneity and IngamellsÆs tests done in Chilean porphyry copper deposits that belong to CODELCO Chile (Chuquicamata, Mina Sur, Radomiro Tomic, El Salvador, Andina and Teniente), in different geological units (endogenous oxides, exotic oxides, supergene sulfides and hypogene sulfides) and for several elements (Cut, Cus, Mo and As). These tests, considering the natural variability, have helped us develop accurate sampling protocols to minimise the fundamental error to acceptable levels. A major contribution of these tests (more than 30) is the generation of secure sampling protocols using the highest sampling constant obtained in the tests, for new porphyry copper deposits that donÆt have information given by heterogeneity and IngamellsÆs tests.

Jan 1, 2005

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc patented gassed emulsion technology, is summarised in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimise the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2004

By Dunbavan M, Mallett C. W

The sequence of development and back analysis of the failure of a spoil pile in the 1B pit of the Moura Mine are given. The mode of failure was a two-wedge mechanism with a basal slip plane passing through a clay band about 2 m below the pit floor. Remedial actions for improving spoil pile stability are discussed.

Jan 1, 1981

By Webster SS

This paper uses computer modelling tech- niques to compare and contrast anomaly patterns obtained with fluxgate (vertical field) and proton precession (total field) magnetometers at typical latitudes in northern and southern Australia. The use of these modelling tech- niques is suggested as an aid to magnetic interpretation and field examples are included from Tasmania and the Northern Territory.

Jan 1, 1975

The products of Lower Miocene calc- alkaline activity on the east coast of Northland, New Zealand are described and contrasted with coeval rocks of the northern North Island. These rocks, the Eastern Volcanic Belt (EVB), occur in four main centres aligned north-west to south east as either plutonic/hyabyssal bodies or as agglomeratic piles and dyke intrusions. Significantly the plutonic members always occur to the north-west of the volcanic members, probably indicative of differential uplift along faults (upthrown to the north) aligned perpendicular to the EVB. A full basalt-rhyolite (diorite-granodiorite/ adamellite) spectrum is represented, with a temporal progression towards the silica-rich endmembers indicated by cross-cutting field relationships. Modal mineralogy parallels this trend, consisting of two-pyroxene, hornblende, biotite, quartz/alkali feldspar modal assemblages, and with rare occurrences of olivine and garnet-bearing volcanic phases. Chemically the EVB is medium-K, calc-alkaline (with respect to AFM and total-Fe/MgO vs. Si02 indices) and quartz and hypersthene normative. The thirty two available K-Prisotope dates indicate that activity was largely confined to the Lower Miocene (24Ma-16Ma), with an apparent younging towards the south east. Initial B7Sr/e Sr ratios (0.70335- 0.70679) are indicative of a continental- arc-type setting, however it is unlikely that a straightforward tectonic reconstruction for this part, of the Pacific Margin is possible. Evidence from xenoliths, both petrologic and isotope, within EVB magmas and from regional geologic studies suggests that hypotheses pertaining to a volcanic arc sited over a subduction zone may hold little relevance in this case. The review concludes that the EVB developed from the partial melting of a geochemically evolved lower crust as indicated by xenolith evidence. This occurred in response to thickening initiated by a short-lived obductive event in the uppermost Oligocene, and controlled spatially by pre-existing basement structure. Intra-suite chemical and mineralogic variation reflects not only crustal variability, but localized differences in physico-chemical conditions best illustrated by the rare occurrences of olivine and garnet.

Jan 1, 1987

Mining software packages are used extensively in industry for resource estimation as well as for mine design and operation. Research undertaken in the W H Bryan Mining Geology Research Unit at the University of Queensland has shown that modifi

Jan 1, 1994

LOCATIONThe property of the Mount Isa Mines Ltd. is situated in Western Queensland, 603 miles by rail west of Townsville, the nearest seaport. All supplies and the bullion are railed between Mt. Isa and Townsville. The climate is semiarid, and operations are conducted throughout the year without difficulty.WATER SUPPLYThe mill make-up water is obtained from the mine, and also from Rifle Creek reservoir, which is situated 20 miles from Mount Isa. The domestic supply of water is obtained from a series of bores on the company's leases.POWER SUPPLYElectric power at 3300 volts, 3-phase, 50 cycles, is supplied from the company's steam power plant, consisting of two units, each unit comprising one Babcock & Wilcox boiler, supplying steam at 300 lb. pressure per sq: in. to one 5000 kW. turbo-alternator. Pulverized coal is used as fuel, and power is being generated at a cost of 0.45d. per kilowatt hour. The coal used is supplied from the State Coal Mine, Bowen, costing 42/- per ton delivered at Mt. Isa.

Jan 1, 1933

By P Griffin

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway OperationsÆ 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance as a defence against the Global Economic Crisis. Five of the six RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites. The sixth is for Sino IronÆs Cape Preston Project in Western Australia. This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules. The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest semi-autogenous grinding (SAG) mill new liner placement rates ever observed by Russell Mineral Equipment (RME), as would be expected with two, independent Machines working simultaneously in the one mill. The liner replacement rate, averaged over the whole reline is good (27 per cent improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation. This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ædouble headÆ mill liner handler by others. Early performance of EscondidaÆs new RUSSELL TWIN 8 System performance is then compared with recent single machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved. The preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform to develop data collection templates is also discussed in Appendix 1.

Jan 1, 2009

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Jowett A

To compare open circuit lead primary rougher results at Mount Isa Mines Ltd., eleven surveys were made over five weeks of plant operation with varying ore sources, including a specially hauled sample of 100% Black Star ore. Three of the surveys which represented extremes in performance were selected for sizing, cyclosizing and assaying for lead, zinc and iron. A comparison of the flotation kinetics has revealed the similarities (including common problems) and differences for the surveyed ores. The concepts of entrainment and collectorless flotability are used to aid interpretation of the kinetic data.

Jan 1, 1978

By Martin C. H, Met B

INDEX OF CONTENTS:1. Introduction, Explanatory; and Reasons for Coal Cleaning.2. Principles on which Coal Cleaning is based.3. Location of Broken Hill Proprietary Co. Ltd. Plant.4. Description of Processes Selected Barvoys Bath Process; Barvoys Medium Preparation and Treatment; Static Dry Cleaning Plant.5. Detailed Description of Plant.6. Typical Results of Cleaning Operations.INTRODUCTION, EXPLANATORY, AND REASONS FOR COALCLEANING:The Institute proceedings have not previously published any matter on coal cleaning and the reasons thereof; in consequence it has been deemed advisable to allot a part of this paper to explanatory matter, prior to entering into a detailed explanation and description of the Newcastle plant.At the outset it would be as well to consider briefly the kinds of materials from which coal has originated. All coals represent some stage in the decomposition and transformation of vegetable matter laid down in prehistoric times, the vegetable matter undergoing numerous geological changes, such as submergence, overlaying by sediment, with subsequent pressure and re-elevation; these processes may...

Jan 1, 1946

By T Leach, F Kaiqiang

The Jianchaling gold deposit is located about 1200 km south west of Beijing in central China. The deposit was discovered in 1988 by the Northwestern Geological Exploration Bureau (711 Exploration Team). Sino Gold Limited, an Australian based company, developed the mine in 1998 and is currently operating a 1000 t per day underground mine, producing about 80 000 ounces of gold per year. The pre-mine resource for Jianchaling was 1.6 million tonnes at 9.85 g/t gold. The deposit occurs within the east-west trending Mesozoic Qinling-Dabie orogenic belt formed during the Yanshanian Orogeny. In the Jianchaling region, gold mineralisation is primarily hosted by regional west-northwest to east-southeast striking faults, the most important of which, the reverse sinistral F145 fault, hosts the larger gold deposits including Jianchaling. At the mine scale, the most important zone of mineralisation is localised within a shallowly north dipping dilation on the F145 fault. Proterozoic dolomite forms the hangingwall and serpentinite and talc schist the footwall to the fault. Within the footwall, serpentinite is the most important host rock to mineralisation. Initial alteration involves replacement of serpentine to dolomite ¦ pyrite, talc to ankerite ¦ pyrite, and magnetite and chromite to pyrite, the latter locally through a transitional hematite phase. Proximal to feeder structures, the carbonate minerals have undergone partial dissolution and replacement to quartz. Gold is related to arsenean pyrite and marcasite rimming and replacement of early-formed pyrite, and associated with iron release during the processes of dolomitisation, silicification and carbonate dissolution.

Jan 1, 2004