Search Documents

By C Mark, Z Agioutantis

This paper presents an empirical design methodology that is based on successful US roof support systems using both primary and secondary support in coal mining entries and intersections. The recent nationwide dramatic reduction of roof fall rates, especially in areas with weaker roof, can be directly correlated to the effectiveness of the roof support systems. A large database of roof fall histories at several mines is used to define the approximate boundaries of three modes of roof support with respect to roof strength as classified by the Coal Mine Roof Rating (CMRR) and in situ vertical stress as indicated by the depth of cover. These roof support classifications are: • Suspension, where roof bolts mainly provide skin control for strong roof. • Beam building or reinforcement, where a roof of moderate strength can be supported by roof bolts only. • Supplemental (secondary) support, where the primary support by roof bolts may be augmented by several secondary support systems, eg cable bolts, trusses, additional roof bolts or standing supports. The Primary Support Rating index (PSUP) captures the capacity of the primary roof bolt system as a function of the actually implemented roof control plan, ie roof bolt length, roof bolt density, and roof bolt capacity, while it does not consider the type of bolt. The actual PSUP value is compared against a suggested PSUP value derived from statistical analysis of US case histories. Where secondary support is indicated, the expected rock load determines the necessary capacity of the secondary support system. A new (free) software package, Analysis of Mine Roof Support (AMRS), implements the design methodology and also allows comparison with other international indices such as the Reinforcement Density Index (RDI), the PRSUP, etc.

Nov 29, 2022

**Add abstract here**

Jun 1, 2010

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

By M Oyarzún

Direct relationships between rock texture and BWi (grindability index) have been established based on geological and metallurgical information supported by optical microscopy observations, gathered from 731 samples.Each recognised rock texture is observed to be related to a certain BWi range and, this texture is also characteristic of distinct lithological subunits (recognisable at mapping scale). Therefore, this relationship may provide an important tool for early milling in situ estimation.Since each textural type is a response to rock formation conditions, the causality of the relationship between BWi and texture is based on such conditions and, particularly, on the interfacial free energy among its components.According to the abovementioned textural features, the greater the free interfacial energy between mineral components, the greater the necessary energy required to break its grain boundaries and, consequently, the greater the necessary energy required for milling.If the textural evidence indicates that the rock was able to adjust the shape and/or size of its components – in a natural tendency of all systems to minimise energy– then the necessary energy required to break its grain boundaries will be lower.

Sep 5, 2011

By P Hofmeyr, D Pretorius

Iron ore, which is transported by rail from the iron ore mines at Sishen in the Northern Cape, to the Saldanha Iron Ore Terminal in the Western Cape, needs to be analysed while loading to be exported. Every shipment will be sampled and an average analysis of the ore will be produced which is required by the purchaser at the receiving port. On arrival at the iron ore terminal at Saldanha, the ore is tipped from the rail trucks onto conveyor belts to be either stockpiled or direct-loaded. The conveyor belts run under the sampling plant and the ore is sampled periodically by means of an automated cross-belt sampler. This is the first iron ore port sampling facility in which the automated sampler is situated above the conveyor belts and not adjacent to them. A portion of the primary sample taken off the belt is moved to the dedicated sampling laboratory situated behind the cross-belt sampler and over the conveyor belt lines. The sample is split in the laboratory, one split being used for moisture and particle size determination and the other part is dried and then analysed by means of X-ray fluorescence spectrometry (XRFS) on fusion beads for major and minor elements. Particular care is taken to obtain high quality data for penalty elements.This sampling plant is completely automated and from the primary cross-belt sampler to final analysis by XRFS no manual steps are involved. This has meant that some processes are used which are suitable for automation and are ISO compliant but not necessarily ISO-certificated. The ISO manuals were developed with manual laboratory processes in mind. Precautions are also taken to maintain the integrity and representativity of the samples. This paper is a case study?describing?the automated sampling systems used at the Saldanha Iron Ore Terminal sampling facility and laboratory from conveyor belt to analysis.CITATION:Hofmeyr, P and Pretorius, D, 2012. Automated sampling of iron ore for analysis at the Saldanha Iron Ore Terminal in South Africa, in Proceedings Sampling 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By G R. Hancock, S Grant, T Whiteside, J B. C Lowry, J Boyden, T J. Coulthard

Physically-based landform evolution models (LEM) provide a spatial framework to forecast the long-term geomorphic stability of post-mining landscapes. When used to test the relative stability of different landform designs, LEMs may assist with the development of optimal closure designs for rehabilitated mines. However, in order to reduce prediction error, factors controlling landscape evolution must also be accurately represented by models. This requires that the correct sets of processes are represented and that driving parameters used in LEMs are, if necessary, calibrated to the landscape of interest.Vegetation exerts strong controls on the hydrologic and geomorphic processes that drive landscape evolution. Hence, the spatial and temporal scales over which typical patterns in vegetation are represented in different landscapes are important considerations in LEM calibration. However, vegetation is rarely accounted for in LEMs and even when integrated is often represented simply, without representing spatial dynamics of vegetation cover that may impact landform development.This study focuses on characterising vegetation patterns to calibrate a new vegetation module of the The Cellular Automaton Evolutionary Slope and River (CAESAR)-Lisflood LEM to be applied to a conceptual rehabilitated landform of the Ranger uranium mine located in the Alligator Rivers Region (ARR) of northern Australia. In the ARR the spatial dynamics of vegetation over time are largely driven by monsoonal rains and topography. Extensive dry season fires are also common in the region, temporarily reducing vegetation cover where they occur. Hence, hydrology, topography and fire disturbance interact to shape a distinct, yet dynamic, mosaic of different vegetation types of varying cover density. As a basis for calibrating the new vegetation function, the distribution and dynamics of vegetation are characterised for this savannah landscape by remote sensing, in conjunction with ground data.CITATION:Boyden, J, Lowry, J, Coulthard, T, Whiteside, T, Hancock, G and Grant, S, 2016. Accounting for vegetation dynamics in landform evolution modelling, in Proceedings Life-of-Mine 2016 Conference , pp 63–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Weatherstone N

Ironstone outcrops on the Savage River were discovered by State Government Surveyor C. P. Sprent in 1877. The limonitic outcrops were initially regarded as the surface expressions of pos- sible tin-bearing lodes, the tin deposits at Mt. Bischoff to the east having been found in 1871. By the turn of the century, shafts, adits and trenches had been developed on the deposits in the unsuccessful quest for gold, silver and base metals. The deposits were first reported as a possible source of iron ore by Tasmania Department of Mines (TDM) geologists in 1919. Modern exploration began in 1956 with the area registering the best magnetic response during an aeromagnetic survey of North- western Tasmania by the Bureau of Mineral Resources (BMR). The area had previously been reserved by TDM in anticipation of the lifting of the iron ore embargo. Reconnaissance Geologi- cal mapping (TDM) and grid-based magnetometer surveys (BMR) indicated that resources of iron-bearing material could approach hundreds of millions of tons. This provided the incentive for two diamond drill holes funded by TDM which demonstrated iron mineralisation in substantial tonnages, suitable grades and, fol

Jan 1, 1988

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By Y Lanwin

The Australian mining industry, a cornerstone of the nation’s economy, is on a journey towards greater equity and inclusion. Th paper introduces a comprehensive exploration of how universal design principles, stemming from architectural roots, have evolved through automation and digital technology into the more encompassing frameworks of inclusive design and equitable design. The paper proposes a practical framework for those involved in work, facilities and equipment design in the mining industry to identify and assess for equity and inclusion. Universal Design emerged in the 1960s with a primary focus on architecture, aiming to create spaces accessible to people of all abilities. Its foundational principles sought to ensure equitable use, flexibility, simplicity, perceptibility, tolerance for error, low physical effort and optimal spatial considerations. Over time, these principles evolved and expanded beyond physical spaces, finding applications in various fields, including technology, education and transportation. In response to advancements in technology and a growing understanding of the multifaceted nature of diversity, Universal Design evolved into Inclusive Design. Inclusive Design goes further than mere accessibility, considering a broader spectrum of users with varying cognitive, sensory, cultural and socio-economic backgrounds. It emphasises user centred design, customisation options, diverse user research and continuous iteration. Equitable Design emerged as a framework that addresses not only the diversity of needs but also systemic disparities. It emphasises fairness, justice and the elimination of structural inequities. Equitable Design encompasses accessibility and affordability, representation and diversity, ethical considerations and community engagement. This paper will explore the applications of these design principles through a series of case studies including village and on-site facilities, remote operations and office based work design and technology design. By applying these frameworks in a mining context, the paper proposes that mining companies and suppliers can improve diversity, equity and inclusion leading to safer, more engaged and productive workplaces.

Apr 16, 2024

By Nixon J. C, Reynolds C

Three principal features of the ore at Captain's Flat, New South Wales, tend to complicate concentration of the valuable minerals, these being:1. The ore occurs in three more or less separate bodies which vary in texture and mineral ratios. Mining of constant proportions of the three sections, or adequate blending of the ore, is not fully effective, and consequently the flotation section is subjected to feedof varying texture.2. The mineral association in the heavily pyritic ore is extremely intimate. Composite particles exist even at 20 micron sizeI, and probably finer.3. The copper content of the ore averages_about 0,6%, which is high enough to justify recovery of the chalcopyrite in a separate concentrate. A review of the metallurgical history of the mine shows that this feature has been the cause of the several major changes in flowsheet of the flotation section since the commencement of milling.METALLURGICAL HISTORYThe mine started production in January 1939, at the rate of 250 tons per day of sulphide ore, assaying 0·68% Cu, 6·52% Pb, 10·8% Zn, and about 1 dwt. Au and 2 oz. Ag per ton.

Jan 1, 1952

By H Han, d S. Hapugoda, L Lu

With the recent rapid development of Chinese steel industry, the world iron ore resources of good quality are depleting rapidly. As a result, iron ore deposits of lower quality have been or are being developed to meet the market demand and are becoming increasingly important to iron and steel companies. As concentrates have advantages of high Fe grade and less harmful impurities, they are ideal sweeteners to maintain sinter grade and quality when high proportions of low-grade ores are used in the sinter blends. However, due to their fine nature, addition of concentrates will inevitably increase the proportion of adhering fines and reduced the proportion of nucleus particles of the sinter blends, which can adversely affect the green bed permeability and sintering productivity. In the present study, lab scale sintering tests were carried out under the conditions similar to the sintering process to examine the effect of concentrates on the high temperature sintering characteristics of sinter blends and the structure and strength of the resultant sinter analogues.

Sep 18, 2023

The Kunwarara magnesite deposit is the largest known magnesite (MgCO3) deposit in Australia. It is located under black soil plains to the north of Rockhampton in Queensland. The deposit consists of magnesite nodules set in a fine-grained sandstone, siltstone and mudstone matrix. The magnesite is derived from weathering of serpentinite in adjacent hills and transport of magnesium in solution to a Tertiary/Quaternary river system. The magnesium has come out of solution in the active river system, and combined with atmospheric and biogenic CO2 to form magnesite nodules. The magnesite can be very pure with certain varieties up to 98 per cent MgO (LOI free). The deposit has been mined since 1991 and processed into magnesia (MgO) which is sold into refractory, agricultural and other markets. The geologist is an integral part of the small mine technical team. The role of the geologist includes characterisation of the ore through drilling and bulk sampling, supervision of geological aspects of mining and assistance in the optimisation of ore processing.

Jan 1, 2000

By J Whittle

This paper describes what is involved in carrying out a comprehensive optimisation of a long-term operating schedule for a mining complex. It details the data that must be assembled and discusses the different approaches to optimisation and what limitations they put on the variables and constraints that can be handled.CITATION:Whittle, J, 2014. Not for the faint-hearted, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994