Search Documents

By A Parbhakar-Fox, S C. Dominy

The prediction of acid and metalliferous drainage (AMD) from mine waste materials is critically important during all stages of the mine value chain. However, to determine such geoenvironmental characteristics static and kinetic testing of individual waste units must be performed on representative samples. The importance of sample selection cannot be underestimated; it is the single most critical aspect of any geoenvironmental investigation. Poor sampling techniques and inadequate sample selection will contribute to excessive variance, difficulties in interpretation and incorrect assessment. By undertaking mesotextural characterisation based on hyperspectral mineralogical data (with sulfur assay data if available), opportunities to improve sampling strategies are presented. Such data will inform the selection of samples for low-cost total sulfur, paste pH and geoenvironmental logging, which collectively will allow for accurate AMD forecasting and improved sampling practices to be achieved. Once sampled, robust quality assurance/quality control (QA/QC) protocols must be developed where the use of international certified reference standards become obligatory. This is currently not practised, resulting in inter-laboratory discrepancies when undertaking waste classification. Further improvements in geoenvironmental characterisation testing lies in the adoption of blended static testing protocols, whereby blends of waste materials can be efficiently tested so as to give an early forecast as to whether they will produce acidic or metal-laden drainage. Such information is integral in developing a waste schedule that will allow for a non-acid forming waste landform to be constructed right from the start of the operational phase. Ultimately, improvements in this discipline lie in technological innovations with regards to mineralogical characterisation, and by offering geoscience and minerals engineering students a competent education in the discipline. Collectively, this will empower a step-change in AMD prediction and waste handling, and will make the realisation of the United Nations Sustainable Development Goals a reality, rather than a dream.CITATION:Parbhakar-Fox, A and Dominy, S C, 2017. Sampling and blending in geoenvironmental campaigns – current practice and future opportunities, in Proceedings Eighth World Conference on Sampling and Blending , pp 45–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

The Que River Mine is a small under-ground base and precious metals mine located in north-western Tasmania. Current production rate is 220,000 tonne/yr from reserves grading 0.37% copper, 7.1% lead, 12.2% zinc, 195 g/tonne silver and 3.4 g/tonne gold.Ore is mined using longhole open stoping techniques. Cemented fill is placed in primary stopes to permit safe and efficient recovery of pillars. The operation is trackless with both shaft and decline access from surface.Ore produced is trucked 40 km by road to be sold to the Electrolytic Zinc Company of Australia Ltd., for treatment at their Rosebery concentrator.

Jan 1, 1985

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By K Rees

In the ideal world of an underground mining engineer, all narrow vein orebodies would be perfectly straight and continuous, thus would be a dream to mine. However, this is usually not the case. Narrow vein orebodies generally occur in association with shear zones and while shear zones do form linear trends, they most commonly preserve undulating expressions that need to be closely monitored, particularly when overprinted by post-formed structures. The surge in mines using fibrecrete as a primary form of ground support effectively reduces the time available for geological interpretation down to a 30 minute window between bogging and shotcreting. Thus, if the quality of the data collected is not up to scratch, then there is only a limited ability to reassess using 2D face photographs. To negate this, Xstrata Nickel AustralasiaÆs Cosmos mine has upgraded its data collection procedure. Geological information is now collected using photogrammetry survey, producing 3D images of the drive. Once created, the digital image of the drive is loaded into Vulcan, thus enabling geological interpretation to be carried out along entire drives, between levels and in association with all other data (eg drill holes, seismic data, etc). In addition to this, the 3D image can be used to accurately model the location of the ore, enabling stoping panels to be confidently positioned to maximise grade and minimise dilution. However, with the focus at Cosmos changing from narrow vein mining, to bulk mining methods in a more geotechnically complex terrain, the use of the 3D images has become paramount in understanding the structural geometry. Continual interpretation of the data has enabled drive profiles to be maintained through the increased use of ground support in poor ground and the redesign of development to enable optimal intersection of structures. Nevertheless, while the collection of quality data is important, it is only the effective use of the data, which enables significant gains in understanding.CITATION:Rees, K, 2012. The benefits of using photogrammetry in the geological interpretation of the Cosmos nickel mine, in Proceedings Narrow Vein Mining 2012 , pp 145-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By A Lyon

The minerals industry, as many other industries, has a wealth of indicators and a thriving æindustryÆ in their development, measurement and reporting. It is natural for this to occur for a new endeavour. However, perhaps it is time for the community concerned with minerals industry indicators to ask whether we have achieved a certain maturation whereby proliferation of indicators may be replaced by a more disciplined and constrained approach. In many natural and engineered systems, thermodynamics provides well-understood and tested constraints. Indicators that are uninterpretable in this framework are not considered acceptable. This paper provides initial evidence that such a formalism may be possible for mine sustainability. The formalism developed does not claim to have the rigour of thermodynamics. However, it does provide a first step towards formalising selection of indicators on the basis of their true comprehensibility. A set of simple equations is developed that represent the conventional five capitals (actually we use six because we separate renewable and non-renewable natural capital) and how they are linked. This is coded into a simulation model. The base equations are then used to develop a system level indicator of sustainability performance, which is asserted to be a reflection of the mineÆs reputation. We define a least sustainable state, termed æmaximum revenue mining (MRM)Æ in the system and define the degree of system sustainability as how far the system is from the MRM. We then introduce a simple mechanism whereby different actors can express differing views on the emphasis for the distance from MRM. Sustainability thereby becomes a non-unique thing that is defined by a distance from MRM and a set of preferences across the capitals.

Jan 1, 2009

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

By Murphy A. S, Budod A

The Philex concentrator represents the first time Jameson Cells have been used in a cleaner scavenger application or in large scale flotation in roughing and scavenging. This necessitated a major change in Jameson cell design as well as a chan

Jan 1, 1997

Mount Isa Mines' Hilton Mine was brought into large-scale production in 1990/91 at a time of sharply falling metal prices. To ensure the operation's survival and eventual prosperity there was an urgent need to reduce operating costs and increase revenue. A target of a 40 per cent increase in productivity over five years was set. Strategies to obtain the required improvements were developed on the basis of greater involvement and increased contribution from the workforce, major changes to the mining methods and the development and application of new technology. This paper describes the organisational, operational and technological changes that have been implemented at Hilton and presents the results achieved to-date.

Jan 1, 1993

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By C McCamley

"The requisite for maintaining optimal carbon concentration levels in a carbon-in-leach (CIL) circuit is of paramount importance in the prevention of gold losses. The process’s ability to recover gold from the aqueous phase is primarily dependent on the carbon loading profile of the CIL train.Newmont Boddington Gold (NBG) have over 2015 tested the Mintek online carbon concentration wmeter (C2 Meter) suitability for effective carbon concentration measurements in their CIL circuit compared to the standard method where the readings are taken twice a shift by the operations staff. The C2 meter works by passing a 1MHz ultrasonic signal through a slurry containing carbon where there is a relationship between the carbon concentration and the attenuation of that signal.It also highlighted another area where the C2 meter could be implemented at NBG whereby the instrument can be as a cautionary device for carbon losses in place of carbon safety screens.Citation:McCamley, C, 2016. Continuous Carbon Concentration Measurement at Newmont Boddington Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 207–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Bedford D. J

The post pillar cut and fill stoping method has been adopted by King Island Scheelite for the extraction of the main Dolphin orebody. The orebody is a massive, tabular deposit varying from 10 to 50 metres in thickness, and dipping at approximately 30¦ towards and under the sea bed. The mining method was selected for 1. maintenance of hangingwall support under the sea bed; 2. maximisation of first stage ore extraction; 3. flexibility of mining, allowing maintenance of grade and selective mining around waste bands within the orebody, and 4. compatibility of existing equipment both with stoping and the on-going underground mine development programme. Stope parameters were established on the basis of initial rock stress analyses, and since the undercut phase of mining the stoping programme has been monitored with various types of deformation measuring devices installed in a series of large diameter boreholes.

Jan 1, 1977

Coal Mining Land Use on the southern coalfields often preceded other land uses. Over the past century overlying land use has altered significantly, particularly with water supply storage development, road system building, railways, pipelines, electricity reticulation schemes and general urban develop- ment. National Parks were declared over coal bearing lands. Little regard was paid to the coal under the land surface by land developers, Government instrumentalities, central planners and the Metropolitan Water, Sewerage and Drainage Board and others, and little value was placed on this valuable energy source. These bodies derived no benefit from the under- lying mineral. In these circumstances, mine operators and such surface land users were put into adversary roles. Mass sterilisation of coal resources resulted. The loss of reserves continues, although the problem has become better under- stood. An Energy Impact Statement (EIS) submission by all surface land developers has been proposed as a means to justify the impact of the development on the coal reserves Beneath.

Jan 1, 1979

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015