Search Documents

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

Both as an energy source and as a raw material, natural gas is playing an increasingly important role as a catalyst for the development, continuation and rebirth of mining projects in Australia. Pipelines are the vital link in making natural gas available to a region and to individual mines. This paper will cover the role of pipelines in supplying mining projects in Australia, the development and status of the Ballera to Mount Isa gas pipeline and the future prospects for gas pipelines in the Carpentaria Mineral Province.

Jan 1, 1998

Carbonate-hosted massive sulfide ores of the American cordillera compose a distinctive genetic class. Discordant fea-tures of occurrence together with measured high-temperatures of formation indicate their essential epigenetic character and close spatial association with centers of thermal activity during evolution of the cordillera. Their metallogenic character is complex from region to region: Cu-Zn-Pb-Ag, Pb-Zn-Ag, and Cu-Zn-Ag-Au represent extremes of composition and each may be identified with specific terranes of occurrence, notwithstand-ing an inferred common process of formation. Beyond the presence of a thermal center, other controls that may be identi-fied include apparent but obscure properties of primary perme-ability or chemistry of hosting strata, and secondary controls are imposed by stratigraphic differences in which permeability is strongly contrasted. Structures that act as channelways may be identified in some instances. Notwithstanding their intrinsic value, search for these ores is difficult and requires the solution of complex geochemical and three-dimensional geometric problems.

Jan 1, 1990

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Roe P, Lowell A

This paper outlines software development and design work carried out by Mincom Pty Ltd in collaboration with Capricorn Coal Management (CAPCOAL) for computer based design of rehabilitated strip mine landforms at German Creek Mine. Current developments and future application areas for this software are also discussed in relation to other mines in Central Queensland. The development program was initiated in response to statutory requirements placed on mining companies in 1990 to produce a five year Plan of Operations which was to include a contour plan of the final rehabilitated mine landform at the end of the five year planning period. This plan was to be submitted to the Department of Resource Industries (DRI) by 1 December 1990. Due to the limited time given to prepare the plan, a work program was formulated in collaboration with Mincom Pty Ltd to develop suitable software to carry out the design work and provide the required plans and quantities. The software had to include computer based methods to allow design of the proposed landform in line with the rehabilitation strategy adopted by CAPCOAL at the time.

Jan 1, 1991

By Nekitel S, Arumba J, Kopi G, Findlay RH

The Kainantu area lies within the composite Scrapland terrane which is composed of Mesozoic metamorphic and intrusive units, overlain by Cenozoic marine sediments, volcanic and intrus-ive units and Quaternary fluvial sedi-ments.Four deformations (Dl, D2, D3, D4) are recognised within the Mesozoic sequences, which consist of greenschist to amphibolite facies schist derived from felsic to intermediate pyroclastic rocks and pelitic sediments. The second, third and fourth fold events are present in the Cenozoic sequence, and these rocks are broken by thrusts related to northwest trending D3 folds. South-dipping, possibly lystric, normal faults are recognised and may be related to uplift and exposure of the metamorphic rocks as core complexes.Known mineralisation in the area consists of gold and copper skarn deposits, porphyry copper deposits, shear-hosted gold deposits, epithermal vein deposits and gold placer deposits. Over 35 hard rock and 18 gold placer deposits are known within the area. Of significance are the Kathnell shear-hosted auriferous quartz veins; such structurally controlled veins may be more widespread than proposed prev-iously and offer a new exploration target.

Jan 1, 1994

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

The microstructures exhibited by ilmenite in its association with other oxide minerals have been the subject of a number of papers, the most comprehensive of which is that by Ramdohr. The following observations in some degree extend his conclusions. They are based upon a study of about sixty specimens of "massive" ilmenite and titaniferous ores from a number of wIdely 'scattered Australian localities. Specimens of this character proved much rarer than was expected. The collection was gathered together through the generous aid of the University Geological Departments, Geological Surveys, and Natural History Museums of the several States of the Commonwealth, all of which contributed such specimens of local origin, as they possessed. Special thanks are due to Dr. E. S. Simpson, of Western Australia, who made available several highly interesting specimens, together with his...

Jan 1, 1938

This paper is written as a supplement to that of Edwards, Baker and Knight on "The Geology of the Wonthaggi Coalfield" 1, the West Area pit being in an early developmental stage at the time of their paper. The thin seams to the west of Dudley Basin 2 had beenknown for many years but it was not until 1935 that it became necessary to work them. The West Area Pit came into production as Dudley Area Pit approached exhaustion in 1937. From available information it was estimated that early work would be in a 36in. bottom seam. The present top seam was not included in the reserves, but it was to be extracted where it proved thick enough for economical working.THE SEAMSEdwards, Baker and :Knight (1944) had insufficient information to correlate positively the West Area seams with those in the Dudley Basin. Their opinion was, however, that they were a westerly extension of the Bottom Seam. Since then the driving of the present north-east heading towards No. 4 Bench McBride Tunnel has established that the West Area seams are those worked as Bottom Seam in the Dudley Basin. West Area Top Seam is a seam that occurred above the Bottom Seam in the Dudley Basin. Only sporadic attempts have been made to work it in Central Area, because 30in. was considered an economic minimum height until recent times. This seam should not be confused with Top Seam, Dudley Basin, which lies some 300ft. above the bottom seam measures and except in isolated areas over deeper workings has been eroded away in West Area.

Jan 1, 1953

By G N. Phillips

No new goldfields have been found in the Witwatersrand Basin for over 60 years, and one consequence of this is a long-term decline in gold production. Exploration throughout this period has been based on the placer model that infers alluvial transport of gold grains and then sedimentary sorting in the basin; however, there is no viable source for so much alluvial gold and no single sedimentary setting that hosts the gold.An alternative genetic model can now provide a quantified explanation for the source of the gold, and it does not rely on alluvial gold processes. The hydrothermal model can easily explain the source of the Witwatersrand gold as being derived from the background gold at parts per billion (ppb) level throughout the Kaapvaal craton of South Africa. This gold is involved in metamorphic processes, available for solution in metamorphic fluids, and hence may be transported whilst dissolved in fluid into the Witwatersrand Basin. The hydrothermal model warrants consideration as it can explain the source of gold, the large alteration halo in the goldfields, the mineralogy, and especially the gold-carbon association.Working on the premise that if one model (placer) is not giving the desired results (discovery of new goldfields), then it may be prudent to consider alternatives. Application of a hydrothermal model to guide exploration would place importance on large and small early structures in and around the Witwatersrand Basin; it would also emphasise the geochemical nature of potential host rocks (especially C and Fe) rather than their sedimentary origin.CITATION:Phillips, G N, 2013. Origin of Witwatersrand Gold - a viable source region and source process for gold, in Proceedings World Gold 2013 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

By A Price, D Okle, K Brooks

The operation of flotation plants has been improved over the years by use of fundamentally based design techniques, a better understanding of reagent chemistry, online metal analysis and the use of digital control systems. However, optimal operation of flotation banks is not consistently achieved using manual operation. The reason for this is that the system is a highly interacting one, with changes in air addition, cell interface level and reagent dosages all being available, without it necessarily being clear as to which change should be made for a particular situation.This situation is made more complex by the fact that the feed to a flotation bank can vary in flowrate, composition and density over a fairly short period of time. It is not possible for a human operator to reject these disturbances, given the extent of the operation that is typically being monitored.Model predictive control (MPC) is a control and optimisation technique, developed in the oil refining industry, that aims to manage just such interacting multiple input multiple output (MIMO) systems. This technology makes use of linear dynamic models of the plant, that are experimentally derived. These models are then used in a receding horizon strategy to determine an optimal trajectory of the inputs to the system.MPC has been applied to four areas of the lead zinc flotation unit at Mount Isa mines. A total of 31 cells are being controlled by the system, which varies air to the cells, levels and reagent addition on a minute-by minute basis. The MPC controls concentrate and tail grades, reagent dosages, as well as recoveries to ranges set by the plant metallurgists.The development of the MPCs is discussed, together with the benefits realised. The key factors in insuring an ongoing return on investment are described.CITATION:Price, A, Okle, D and Brooks, K, 2018. Glencore Mount Isa lead zinc flotation circuit – experiences from the implementation of model predictive control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 101–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

The Mungana group of mines, in the Chillagoe district, yielded 334,000 tons of ore giving 31,831 tons of lead, 7,907 tons of copper and 3,228,600 ounces of silver. The Girofla mine produced approximately 220,000 tons of ore, and with the Lady J ane mine supplied most of the ore from this centre. The deposit was discovered in 1888, but active development did not commence from the main shaft until 1898. A subsidiary of the New Chillagoe Railway and Mining Co. Ltd., the Mungana (Chillagoe) Mining Co. Ltd., worked the mine from 1902 until 1914, selling copper, copper-lead, lead ores and fluxes to the smelters at Chillagoe. The smelters stopped operations in 1914 when the richer ores of the Girofla had been worked out and production from the Lady Jane had ceased due to heavyground and fire. The Girofla shaft was 823ft. deep with a cross-cut at 810ft. At the 710ft. level contour drives had delineated the orebody, which had been stoped about 10ft. above the level. Except for flux ores which had been stoped only for favourable smelter tariffs, the orebody was practically exhausted above the 610ft. leveL Under company ownership the mine yielded 139,265 tons of an average grade of 4.QlYr copper, 16.2% lead and 12.5 oz. per ton silver.In 1921 the Queensland Government re-opened the mine and worked it until 1927. The North Lode (Fig. 2) was discovered almost immediately at the 100ft. level and was worked down to the 410ft. leveL The ore from this branch and the completion of the stope at the 710ft. level yielded about 80,000 tons of ore averaging 0.4 copper, 9.8 lead and 7.8 oz. per ton silver during this period.

Jan 1, 1953

Selection of mining methods, stope dimensions and stoping sequences is usually based on comparisons with other similar orebodies or rocktypes. Rock mechanics principles assist the process, which can be further improved by application of rock mechanics' models - in particular, computer based stress analysis techniques. These models vary in capabilities and potential application but, basically, can be subdivided into techniques which only model the surface of excavations, and those which model the total volume to be analysed. To address the wide range of geometries, stoping methods and sequences, and geomechanical environments at Mount Isa Mines, a number of models have been developed. By presenting examples of their actual and potential application it is demonstrated that appropriate use of these techniques will assist in the determination of mining parameters and improve ore recovery. Examples presented cover sequencing in tabular and massive orebodies, location of shafts and shaft pillars, and backfill and hanging-wall stability. It is concluded that surface techniques are more appropriate for regional analyses and volume techniques are more suited to analyses of detailed, local geometry. Colour computer graphics should be an integral part of data preparation, and results interpretation and Presentation.

Jan 1, 1986

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023