Search Documents

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

By J Coombes

There is much debate on the Competent Persons qualifying criteria for providing classified resource estimates for public reporting. The CRIRSCO family of codes including the JORC Code, SAMREC, PERC and NI43–101, require Competent Persons to have at least five years ‘relevant’ experience and belong to professional bodies. These codes provide further, albeit vague, guidelines to assist individuals with their personal decision to take on the mantle of ‘Competent Person’. There is a risk, however, that these qualifying criteria can result in ill-prepared Competent Persons whose actions and recommendations would undermine their own reputation and that of the organisations that employ them; the integrity of the profession and the principles based reporting systems; as well as the stability of stock markets that rely on these estimates.Based on doctoral study on the development of professional competency within the mining industry, this paper presents an evaluation of the suitability of the current qualifying criteria as well as an analysis of alternative criteria. The research included a series of interviews with industry experts and an online survey of resource geologists. Semi-structured interviews provided a sense of experts’ expectations and interpretation of the current definition of ‘Competent Person’. The comprehensive online survey included a self-assessment, a series of situational questions designed to evaluate responses to typical resource geology scenarios and a set of open-ended questions relating to factors contributing to competency development.A summary of the data analysis, interpretation of the results and a set of recommendations for revised ‘Competent Person’ qualifying criteria are presented. This paper contributes to the conversation on what makes a person suitably qualified to report classified resource estimates and provides practical targets that can be used in the professional development of resource geologists.CITATION:Coombes, J, 2014. Redefining Competent Persons criteria for resource geologists, in Proceedings Ninth International Mining Geology Conference 2014 , pp 153–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

By D J. Brake

There are many sources of gas in underground mines including development and production blasting, strata gases, spontaneous combustion, diesel equipment, chemicals used for a wide range of functions, welding activities and fires.It is only in relatively recent times that electronic gas monitors (or detectors) have become both safe and affordable for routine use.In modern mines, gas monitors should be in daily use by the ventilation department as well as blasting re-entry (or clearance) crews, and are often used by drilling crews, shift supervisors, hygienists and mine rescue or fire fighting crews.When first released, electronic gas monitors needed to be sent off-site periodically for calibration at a suitable accredited laboratory. Between calibrations, their accuracy was unknown. More recently, ‘bump testing’ and field calibration has become possible on the mine site, improving both reliability and safety as well as reducing the total number of gas monitors that need to be in use.There has been almost an overwhelming increase in the number and sophistication of gas monitor features in recent years. This paper reports on a case study into the key criteria that ventilation practitioners should be aware of with respect to the specification and selection of the most recent gas monitoring systems, and recommends good practice for site-based operation and calibration.CITATION:Brake, D J, 2015. Specification and selection of hand-held gas monitors (detectors) for underground mines, in Proceedings The Australian Mine Ventilation Conference, pp 143–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Fowler

The unpredictability of the location, grade and width of narrow-vein deposits presents difficulties for mine geologists and engineers attempting to estimate, schedule, forecast and mine their deposit profitably. This unpredictability stems not only from the grade distribution within a vein, but also the irregularity of vein geometry in three-dimensional (3D) space. Traditional deterministic methods of modelling vein geometry do not account for the inherent variability of the veins, resulting in significant errors when using limited drill hole information. This paper presents a probabilistic method of modelling narrow-vein deposits using sequential gaussian simulation (SGS), which can quantify this variability and improve production forecasts. Vein geometry, thickness and grade are simulated to provide a number of different equi-probable realisations that each honour the drill hole and face sample input statistics. An example is presented from the Augusta narrow-vein Au-Sb mine in central Victoria, where the simulation results are validated against the input data and survey pick-ups of the veins along ore drives.

Aug 22, 2011

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

Mr. President, Ladies and Gentlemen, it gives me great pleasure to welcome you, on behalf of the Council and Administration, to this University and extend to you our very best wishes for a most successful and stimulating symposium. We as a College of the University of N.S.W. were always proud of the excellent support we received from your Institute members and the close association that existed between our organisations. Now we have matured into the University of Wollongong and have to stand on our own feet, we will need all the support we can get from such bodies as yours to ensure that we are not only producing graduates but are also playing a vital role in the community. Although there is no planning for a school of Mining Engineering in the near future, we do look forward to this being a viable proposition eventually and we will then be able to offer to your Institute wider facilities for your activities and ones which will embrace both the Mining and Metallurgy phases. Thank you Mr. President.

Jan 1, 1975

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By Hartley JS, Wills KJA

The Thalanga massive sulphide deposit is hosted by Upper Cambrian rhyolites and volcaniclastics of the Mt. Windsor Volcanics near their contact with overlying dacites, rhyolites and sediments of the Trooper Creek Formation. The ores and host rocks have been subjected to a single strong deformation and to lower to middle greenschist facies metamorphism. A main lens with surface gossan dimensions of 55U m x 6 m dips steeply, plunges shallowly to the west and is offset by a series of normal faults. It is flanked by smaller lenses to the east where the mineralized horizon is stopea out by granite. The area to the east and south of the gossan is masked by Tertiary cover. A complex exhalite package is represented by banded sphalerite-pyrite- galena-chalcopyrite, massive pyrite and chalcopyrite and assemblages dominated by dolomite, chlorite-actinolite, tremolite, talc, barite and rare gypsum. Accessory tetrahedrite, arsenopyrite, bismuthinite, magnetite and native gold are associated locally. Pods of quartz-magnetite formed distally. The ores are underlain by strongly to moderately pyrite-silica-sericite altered rhyolites with the strongest alteration closest to an interred synvolcanic fault. This alteration is characterised by an enrichment in MgO, Na2O, FeS2 and base metals with a depletion in CaO and Na2O. There is a general enrichment in Pb and Zn towards the hanging wall with some enrichment of Cu near the base of the main lens due to replacement by ore tiuias near vent discharge sites. Zonation of Cu to 2n-Pb in also evident over narrow intervals

Jan 1, 1987

By M Rayner, C Tsouris, A Komelkov

X-ray fluorescence (XRF) is a widely accepted technique for the elemental analysis of iron ores and their concentrates. Wavelength-dispersive, or WDXRF, and energy-dispersive, or EDXRF, spectrometers offer distinct advantages for particular applications, elements and concentration ranges and are, therefore, more complimentary than people might realise. A key example is the ability of EDXRF to identify, and often quantify, unexpected elements in production samples that would typically be missed by routine WDXRF. In this paper we discuss recent technological advances in XRF and present a novel application example that demonstrates the additional technical and practical benefits of using both EDXRF and WDXRF to characterise iron ores and concentrates.CITATION:Tsouris, C, Komelkov, A and Rayner, M, 2015. A novel approach to the characterisation of iron ores and concentrates using recent advancements in wavelength- and energy-dispersive x-ray fluorescence spectrometers, in Proceedings Iron Ore 2015, pp 591–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Optimisation of the Advanced Automation System at Inmet Mining's PyhSsalmi Mine, Finland

Sep 13, 2010

By J Wood

Steady depletion of the world’s primary copper reserves coupled with a meteoric rise in electronic waste (e-waste) generation has led to secondary copper processing assuming an ever-increasing importance within the global copper industry. Treatment of secondary copper feeds at existing smelting operations has traditionally been performed in the Blast furnace, Peirce-Smith converter and/or anode furnace. In the past decade or more, bath smelting technologies have been preferred for the processing of these materials due to their superior environmental performance and flexibility to operate under a wide range of conditions. This paper focuses on the pyrometallurgical processing of copper secondaries in the Outotec Ausmelt TSL Furnace and some of the unique issues facing secondary copper smelters and downstream gas handling/cleaning equipment.

Aug 8, 2011

Young professionals are riding the current wave of high demand for their services and relatively little competition for placements. The attraction and retention of quality incumbents has therefore become a significant strategic issue for companies in our industry. Money is important, but poorly structured career development and lack of learning opportunities can discourage the highest paid professionals from being enthusiastic and striving for excellence. This will inevitably lead to the search for a new position. Important factors at play include the young professionalÆs lack of understanding of career pathways and poor quality, or lack of, structured on-the-job training and professional development. Too often young and not so young professionals are faced with the reality that fabulous looking (and paying) jobs can be quickly reduced to the monotony of repetitive tasks in an isolating environment. While it is the responsibility of the incumbent to manage their own career and professional development, without experience, how is anyone meant to understand the importance of their roles and the options for career development? Mentoring is therefore essential to the strategic plans of every organisation and the strategic plans of every professional. Mentors will accelerate learning, guide decision making and develop both competency and confidence as they share their experience, both technical and regarding the machinations of a particular discipline, within our industry. Mentors need not be from the same organisation as the mentee and in some cases this may be a distinct advantage. This paper discusses mentoring as an opportunity for young professionals and mentors to initiate and maintain a supportive relationship, the responsibility of management to get mentoring right and the responsibility of young professionals to demand the opportunity for professional development through mentoring.

Jan 1, 2006

By P Voulgaris

The Osborne Mine commenced production from an open pit in December 1994 with the first ore being hauled from underground one year later. Currently all ore is hauled up a decline by trucks until the shaft system is commissioned in early-1998. The mine is hosted within a multiply deformed and complex sequence of metamorphic, igneous and metasomatic rocks of mid Proterozoic age that are concealed beneath 20-40 metres of Mesozoic sedimentary cover. Epigenetic and largely hypogene copper - gold mineralisation occurs in a close spatial relationship with quartz - magnetite ironstones and is an important example of a significant mineralisation style in the Mt Isa inlier. Life of mine concentrator production, to year end 1997, totals 3.2 Mt of ore at 3.40 per cent Cu and 1.13 g/t Au. Total metal produced was 97 000 tonnes of copper and 2900 Kg of gold (95 600 oz) from some 348 000 tonnes of dry concentrates averaging 28.01 per cent Cu and 6.99 g/t Au. At the start of 1998 OsborneÆs total measured and indicated resource was stated at 11.38 Mt at 3.24 per cent Cu and 1.21 g/t Au with an ore reserve of 11.42 Mt at 2.90 per cent Cu and 1.09 g/t Au. Exploration efforts in and around the mine have been increased since 1996 and have resulted in an early success, with a 28 per cent increase in ore reserves since mine start-up, and the establishment of a 1.5 Mt inferred resource open to depth. During 1997 the performance of the concentrator has exceeded expectations with throughput having been increased to 1.45 Mt per annum. The Mining Cycle at Osborne has proceeded from discovery through feasibility and is currently seen to be in the latter part of the development stage and/or the early part of an expansion stage. This paper will describe the role of geology and exploration within these stages and will highlight how a number of key interpretations and decisions based on geology have both favourably and unfavourably affected the project.

Jan 1, 1998

By M Gasparon, J Harris, T Baumgartl, D J. Williams, M Edraki, P A. Kirsch, D Rowe

RISKGATE, an Australian Coal Association Research Program-funded (ACARP) initiative, has been designed to assist the Australian coal mining industry in improving minimum standards for safety performance, efficiency, operating practice and training. The online system is innovative in that it is built upon a foundation of industry expert knowledge gathered through action research workshops, which is further supported by a broad array of industry, academic and technical resources. In operation, RISKGATE offers a continuum for knowledge transfer and communication of current practice in risk identification, assessment and management in the coal mining industry. The primary mission of RISKGATE is to focus industry attention on prioritising control management as a way to achieve acceptable risk.A Coal Mine Tailings Dam Module has recently been added to the RISKGATE suite. The key risk, or initiating event, associated with coalmine tailings dams is catastrophic failure of the dam, leading to the release of tailings and water. This can occur due to geotechnical instability of the dam itself or of its foundation, overtopping and erosion of the dam, and piping failure of the dam itself or of its foundation. Coalmine tailings dams are also prone to seepage into the foundation and through the dam, particularly during operation when large volumes of water are discharged with the tailings. The most significant risk associated with seepage is the release of potentially contaminated water to the environment. Contamination can take the form of elevated salinity, acidity and dissolved metals. Run-off from coalmine tailings can cause erosion and can also potentially contain contaminants. Desiccation of the tailings surface can result in dust generation and dispersion.The paper presents the background and context of the RISKGATE project, the need for the addition of the RISKGATE Coal Mine Tailings Dam Module, and a description of the developed module, including the five initiating events considered, their causes and associated preventive controls, and their consequences and associated mitigating controls. This paper concludes with a discussion of the ways in which Australia’s coal mining companies are starting to apply the RISKGATE body of knowledge at their sites, which will flow onto the management of their tailings dams.CITATION:Williams, D J, Kirsch, P A, Gasparon, M, Baumgartl, T, Edraki, M, Rowe, D and Harris, J, ?2014. Application of RISKGATE to coal mine tailings dams, in Proceedings Life-of-Mine 2014 , pp 219–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The purpose of this paper is to discuss briefly the problems encountered in designing and sinking No 7 shaft, and to present the methods employed in the operation.The illustrations accompanying the paper show the details of the construction of the equipment used in completing No 7 shaft, consequently the descriptions appearing in the text are brief outlines only. Mineral leases Nos 7 and 8, held by the Broken Hill South Limited, comprise an area of 69.5 acres. The length of the holding is approximately 2500 ft.The western orebodies, which are the main producing masses, enter the property at the northern bonndary. Generally, the dip of the orebody is to the west, and the pitch to the south, but local variations occur and even a reversal of pitch has been noticed. The angle of dip is approximately 70 degrees and the angle of pitch 45 degrees.

Jan 1, 1932

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017