Search Documents

Detrital gold in the Greymouth-Hokitika area has been won from: (a) gravel of the Pliocene Old Man Group, (b) glacial outwash gravel of Middle and Late Quaternary age, (c) raised shoreline deposits of Middle and Late Quaternary age, (d) deposits resulting from the erosion of (a) to (c). The source of the gold was probably widely dispersed quartz veins in great thicknesses of greywacke and low-grade schist eroded from east of the Alpine Fault, with a contribution from veins in Greenland Group greywacke in the south. At times of high interglacial and post-glacial sea level, gold was concentrated along marine shorelines, and subsequent progressive uplift has resulted in a set of sub-parallel beach leads up to 100 m above present sea level. During glaciations, gold was concentrated in outwash streams close to moraines, especially where ice forming one moraine penetrated and destroyed an older one. Worked deposits in the Old Man Group may also be associated with glaciation. Apart from workings that are essentially extensions of past workings, significant new prospects may depend on inferences as to where prospective deposits are completely obscured by younger ones.

Jan 1, 1996

Au-Ag Recovery from Complex Ore by Flotation

Sep 13, 2010

Smarter Gravity Separation Using the Kelsey Centrifugal Jig With relatively coarse grained and easy-to-process ore sources rapidly dwindling, smarter techniques are becoming more necessary for the continued success of mineral processing operations, while increasing environmental pressures also require more environmentally friendly solutions. Gravity concentration has long been employed to pre-concentrate minerals using water, reducing or eliminating the need for less environmentally friendly processing techniques such as flotation. Conventional gravity recovery devices however, operate in a 1 g environment with limited efficiency in the separation of fine particles of heavy and gangue minerals. More recently developed centrifugal concentrators operate in a multi-g environment and enable finer heavy minerals to be recovered, but also exhibit limited separation efficiency due to the separations being based on solid particle mass differentials. Further enhancement of gravity separation has been achieved using the Kelsey Centrifugal Jig (KCJ), which also operates in a multi-g environment, but separates minerals on the basis of specific gravity differentials, using 'ragging' media and a pulsation mechanism, which maximises the effect of differential particle accelerations. This enables the efficient separation/recovery of minerals down to a particle size of ~6 ¦m and/or separation of minerals with a low specific gravity differential. This paper presents details on the principals of operation of the KCJ, recent improvements in the technology and recent developments in modular KCJ plants, as well as some KCJ application areas, which offer smarter, environmentally friendly processing opportunities for the mineral processing industry.

Sep 13, 2010

Study on Iron Ore Sintering with High Proportion of Specularite Concentrates Specularite iron ores have poor hydrophilicity and ballability as well as bad high-temperature reactivity, which restricts the large-scale application in the sinter and pellet production. In order to make the best use of the specularite concentrates, a novel process of Composite Agglomeration Process (CAP) is applied in this research. By the CAP, the percentage of specularite concentrates in the sinter mixture is increased to no less than 40 per cent as well as the coke breeze dosage is reduced by 0.3 per cent~0.6 per cent. Moreover, all the sintering indexes are obviously improved compared with the traditional sintering process. Researches on the metallurgical performances shows the finished composite agglomerates are high-quality burdens for blast furnaces. This investigation can provide an effective route to utilize the inferior specularite concentrates in the sintering.

Sep 13, 2010

By T Smith, J Hatley

With the increased focus on the need for more uranium mines, this paper presents the design process currently underway for the development of the Millennium deposit in northern Saskatchewan, Canada. This deposit, located 630 - 750 m below surface, will be accessed by two shafts and will be mined by blasthole stoping methods at less than 500 t/d. Mining grade will approximate two per cent U3O8 and mine life is expected to be six to seven years. The project is a joint venture between Cameco, AREVA and JCU. This paper discusses in detail methods used to predict worker radiation exposures, the methods used to monitor the work environment and procedures unique to the uranium industry necessary to minimise worker radiation exposures.

Jan 1, 2008

Though many mining and mineral processing companies have embraced the principles of sustainable development (SD), there is still a significant challenge of applying these in a practical sense, either in plant design or as part of day-to-day operations. The high-level nature of sustainability concepts often do not translate easily into workable activities or business case evaluations. This makes it difficult for engineers and company decision makers to understand whether their actions are making a contribution to sustainable development and a long-term business case. While several organisations have their own SD tools that can, to a degree, help identify these opportunities, they are largely ad-hoc and lack the necessary thoroughness to defensibly value these opportunities. Recognising these serious shortcomings, the Cooperative Research Centre for Sustainable Resource Processing (CSRP) has undertaken the development and trial applications of SUSOP« (SUStainable OPerations), a new concept that is somewhat analogous to HAZOP and the wider risk and safety frameworks used in projects today. The key goal of the SUSOP« research project is to produce a holistic, systematic and rigorous framework for project development, capturing, recording and evaluating SD opportunities and constraints against a chosen sustainability structure (eg Five Capitals). SUSOP« is being developed through an iterative process with input from research institutions and engineering companies. This integrated approach ensures that SUSOP«, in its final form, will have the academic rigour and industry realism required to assist the resource sector contribute to societal sustainability by embedding the concepts and processes into the design and operation of their assets in a meaningful and practical manner. SUSOP« has created much traction with both engineering companies and mining and minerals operators. This conference paper presents an overview of the SUSOP« framework and its current suite of processes as well as highlighting, through practical case studies, its capability to incorporate SD considerations at different phases of an engineering project's development.

Jun 1, 2010

By Jarc H

The steeply dipping silver/lead/zinc orebodies at Mount Isa mine have been extracted most recently by a combination of cut-and-fill and open stoping methods. Bench stoping was first used at Mount Isa Mine seven years ago to allow safe extraction of a highly stressed cut-and-fill stope. Subsequent benches have shown that the method offers significant cost and safety benefits through increased productivity and reduction in man exposure. The success of benching has lead to cut-and-fill mining being replaced at Mount Isa.Significant resources have been focussed to optimise benching. This paper describes the operational, planning, and research and development aspects which have contributed to the method to date. A brief look is also taken at the future direction of benching at Mount Isa.

Jan 1, 1992

By J Temos

This paper outlines a number of immediate practical approaches to continuous improvement in environmental management in the minerals industry. It puts these into context with longer time-frame step-change approaches whose gestation may take a decade. Examples of improvements and approaches are drawn from WMC operations.

Jan 1, 2002

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

A 3-D computerised model of the southern part of Greymouth Coal Limited's Coal Mining Licence area has recently been completed. This model, and associated 3-D CAD tools, has/is being used to optimise drillhole spacing during exploratory data collection and as a visualisation and interpretation aid. This model will also provide the basis for future mine planning, with the emphasis on an optimal mine outline to maximise safety and profitable coal extraction. Previous use of computer techniques was restricted to drillhole database entry, storage and log production. Recently a 3-D geological/structural model was created for the Southern Rapahoe Sector of the Greymouth Coalfield. Geostatistical analysis of the database highlights the inadequacy of the present drillhole spacing for preliminary mine planning. The sparsity of hard data at depth results in a lower level of confidence in the accuracy of the 3-D model. Nevertheless, the model and 3-D CAD techniques has been used to target and refine ongoing resource evaluation, and provides the basis for initial reserves. In the future the geologic model will be used as the basis for preliminary and later (optimal) mine planning. It is also expected to accommodate other forms of data input in seam drilling and seismic. Development of the 3-D computer model was a first in the Greymouth Coalfield and highlights both the use of computerised techniques for resource evaluation and mining, and the effects of wide spaced drillhole data on model accuracy. The computer will continue to provide the most efficient and cost effective tool for optimal resource evaluation and mine planning as Greymouth Coal Limited moves from feasibility/mine planning to full production. The increased use of computer-based methods for mine planning should be seen as part of 'The Changing Face of West Coast Mining' in line with the theme of this Conference.

Jan 1, 1996

By G C. Sen

All mining and quarrying operations that employ blasting to fragment and move broken ground have a price to pay for æby-productsÆ such as vibration and noise. These æby-productsÆ cannot be eliminated but they can be controlled and modern blasting techniques have improved to the point that excessive environmental restrictions can be adhered to whilst maintaining acceptable production rates and quality. Accurate measurement is the key to control, and as the environmental limits are becoming tighter, the proper way to measure vibrations from blasting operations becomes an integral part of the mining or quarrying operations. The basic vibration monitoring system consists of a primary sensor connected to a data logger and computer software for the analysis of the signal received and recorded. Currently, as with all fields of measurement, much improvement has occurred over the past decade, and electronic devices are much more accurate and reliable. Data analysis has also improved considerably with the computing power that is available to field operatives today. Mounting the primary sensor has been often overlooked in supposed æstandardsÆ with procedures such as double sided tape, resting on a flat surface provided the vibration level is less than a given amount. But if it is worth going to the expense of the monitoring equipment and manpower, surely it is worth a little extra effort to ensure the primary sensor is coupled to the ground effectively. The primary sensor must move with the ground and measure this movement; so if the primary sensor is allowed to move without respect to the ground (ie poor coupling to the ground) then a false record of the physical event will be measured. This scenario can easily be a practical reality if the primary sensor coupling method to the ground is not effective. In this study a number of mounting methods were fabricated and connected to similar data monitors and a series of ænormalÆ production blasts were used as the vibration source. These mounting devices were measured against an in-house procedure (the æstandardÆ) and the relative merits compared. A laboratory investigation was also carried out to look at the physical parameters of the æsoil and their effect on vibration attenuation of the in-house standard method.

Jan 1, 1999

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By D Nicoli, P Feltoe

The operation of grinding circuits are vital to the success of most mineral processing operations in the provision of effective size reduction whilst maximising throughput. However these same circuits, and especially semi-autogenous grinding (SAG) mills, are highly interactive with product re-circulations and long time delays. This makes the optimal control of these difficult by conventional controllers, such as PID, which generally places a heavy reliance upon operations for control. In order to account for the peculiarities (such as ore type changes) and the abnormal situations that continually beset these circuits, it is necessary to adapt linear control techniques to cater for these situations. The Honeywell Hi-Spec Solutions SmartGrindTM controller is a marriage of multivariable predictive control (MPC) with techniques that provide adaptation of the control to optimise the circuit under all conditions. Optimal control is achieved by incorporating pattern recognition techniques to detect and act on discrete events (eg ore type changes) and adaptation of the MPC to account for known process and equipment non-linearities. AlcoaÆs Wagerup Refinery is the first site worldwide to have this technology applied to the SAG milling circuits and this has resulted in throughput increases in excess of two per cent and significant improvements in circuit operations. This paper describes the implementation of the control to the refineryÆs Mill 3 bauxite grinding circuit and the capacity/operational improvements achieved thereof.

Jan 1, 2000

No one process, product or effect of the minerals sector can be viewed in isolation when addressing sustainable development. Meaningful assessments of the minerals sector require that its processes and production are drawn together in a generic framework that gives a holistic view of its performance and progress. Lifecycle Assessment is increasingly accepted as an appropriate means of constructing such a framework. It is a step beyond using the simplistic concept of the triple bottom line of social, environmental and economic performance to drive and communicate sustainable development. However, fundamental questions need to be raised about the scope and purpose of lifecycle assessment, such as what effects and performances should be assessed, for whom should they be assessed, and what performance indicators should be used and how should they be selected. The principles of eco-efficiency, industrial ecology, The Natural Step (TNS) and other pertinent philosophies and initiatives driving mineral sector sustainable development are outlined to support a lifecycle stewardship vision for the minerals sector. Articulating this vision through a holistic lifecycle indicator system showing inputs and outputs, natural partnerships, effects on community, environment and economy facilitates recognition of problems, opportunities and partnerships that can be usefully pursued.

Jan 1, 2002

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Flotation Performance Improvement by Air Recovery Optimisation on Roughers and Scavengers

Sep 13, 2010