Search Documents

By AIME AIME

NOTWITHSTANDING the metropolitan appearance of M. L. Haider, the present Chairman of the Petroleum Division, he is not a native New Yorker, but was born at Mandan, N. Dak., Oct. 1, 1904. He began his travels at an early stage in life and after attending the University of Southern California for two years he spent two additional years at Stanford University and was graduated in 1927. After a few months as an analytical chemist for the Portland Cement Co. he became research engineer in the natural gasoline department of the Richfield Oil Co. where he remained for approximately two years before taking a position with the Carter Oil Co. in Oklahoma. He was chief engineer for this company for three years before being trans-

Jan 1, 1945

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By AIME

Annual production of more than 4,000,000 tons of 0.74 percent copper ore and coincident handling of over 5,000,000 tons of waste at the open-pit mine of Castle Dome Copper Co. near Miami, Ariz. takes a lot of power. Manufacturers have ever co-operated with mining companies in providing the required equipment to suit the problem. Power equipment suppliers have done much to make possible the economic and profitable production of copper from low-grade ores. In the future, as mining operations will necessarily handle even lower-grade ores, the ability of the manufacturer to supply the power and mechanical equipment to produce more metal at a fair and reasonable price will be the good right arm of the miner. About 27,000 tons of concentrate is produced from the 4,000,000 tons of ore.

Jan 1, 1948

By AIME

WE produce Charles Van Ormer "Charlie" Millikan as living proof that man need not make a loud noise to be heard. His quietly affable, analytical, and soft-spoken manner in the face of all problems belies his ability to "get tough" when the situation demands it. As a chief engineer with many responsibilities for the success of a large producing company there must have been many occasions to tempt Charlie to excitement, but there are few, if any, who can say they saw him yield. He has an abiding faith in the benefits of hard and persistent work and will not admit the existence of a problem that cannot be reduced by it.

Jan 1, 1948

INTRODUCTION This chapter summarizes porphyry copper deposits within the State of Alaska. Prospecting for porphyry copper-type deposits in Alaska germinated during the 1940's, grew slowly during the '50's, boomed during the '60's, and matured in the '70's. Although large expenditures have been made in the search for porphyry-type deposits, most accrued data lies dormant in company files. However, an adequate base exists in the literature for a general synthesis of areas that contain porphyry prospects. To simplify the summary, porphyry molybdenum deposits as defined by Clark (1972) are omitted. Description of deposits in their geologic setting permits some correlations between deposit characteristics and crustal environment. These correlations allow speculation about the genesis of the deposits. The summary also attempts to group deposits on the basis of general mineralogic characteristics because diorite model deposits are separated from quartz phenocryst-bearing hosts. Data presented in this chapter summarize observations by the author, published descriptions of specific areas and deposits as noted in the bibliography, and comments by various government geologists. E. M. MacKevett, Jr., D. H. Richter, and H. C. Berg of the US Geological Survey have been particularly helpful. Because few comprehensive descriptions of individual porphyry copper deposits exist for this area, much of the data presented is new to the literature. Details of structure, isotopic geochemistry, and petro- genesis for individual deposits are largely lacking and even the general geology of some belts is not well understood. Details on petrography of Alaskan porphyry copper occurrences are inadequate for construction of ternary diagrams (e.g., Figs. 36a, b, pp. 103, 104, for the northern Cordilleran orogen). Petrographic descriptions summarized in the text are largely from published descriptions whose sources are cited. Porphyry copper-type deposits in Alaska include deposits with pervasive pyrite that contain disseminated copper (but not necessarily coproduct molybdenum). Available data preclude differentiating the deposits by size. No Alaskan porphyry copper deposit is now in production but this is believed to be, in part, a function of economics. In some cases available geologic information is in- adequate for classifying deposits. Some de- posits included with porphyry copper may, with further exploration, be demonstrated to be some other genetic type. Alaska has three distinct porphyry copper provinces: the Hogatza plutonic belt, the Continental Margin belt, and the Interior belt. Each belt contains deposits with characteristic geologic features distinct from those of other belts. Fig. 24 shows the continental margin belt to extend inland from

Jan 1, 1978

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By Alfonso Rizo-Patrón, A.M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By Alfonso Rizo-Patrón, A. M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

Discussion of the paper of G. Howell Clevenger and Bhupendranath Ray, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2437 to 2475. ALLERTON S. CUSHMAN,* Washington, D. C.:-I am very much interested in the subject matter of this paper. I have had occasion to speak to this question before. There has recently been so much written and said and claimed about the effect produced by the addition of small quantities of copper to steel that there is certainly an impression abroad that a new and wonderful cure-all has been discovered. Are we facing a method of alchemy by which, at the expenditure of very little trouble and only a few cents' worth of copper per ton, the well-known characteristics of steel with respect to some features are so marvelously changed as in effect to produce a new metal ? I am a great believer in the future of the iron and steel alloy field. I do not think that with all the advances we have made in metallurgy we have begun to scratch the possibilities of usefulness to mankind in the exploration of the alloy field, and I include in that alloy field even what might be designated as the dilute alloy field; that is to say, where a very small quantity of a metal alloyed with iron and steel confers upon it some new or extraordinary qualities. With respect to many of the physical characteristics of the copper-iron or copper-steel alloys I am not particularly competent to speak. With respect, however, to the investigation of corrosion problems and with respect to claims made with regard to resistance to corrosion, I am competent to speak insofar as I have specialized to some extent in that field and have given up a great deal of my time for a great many years to a study of it. Some years ago, being particularly interested in the study of corrosion problems, I received the very generous permission of a large manufacturing concern to use their large open-hearth furnaces any way I saw fit for exploring this particular field. There is not a metallurgist in this room who will not realize the generosity of a manufacturing company who would permit a man to pursue a theory and give him as his material to work with 60 tons of molten metal. At all events, I threw copper into the open-hearth furnace. I explored this alloy field, not in a ittle crucible in which I had to take out portions and have them

Jan 12, 1913

By William Kent

William Kent, Pi.~t~bIJrQh, Pa.: The steel rnanufac.tnret of this country nlust ever he grateful to Dr. Dudley for his painstaking and conscientious endeavor to estaldish the relation between the chemical analysis and the wearing capcity of steel rails. They tnust thank him for the vast array of $acts he presents, and for having given them sixty-four analyses with which to combat his own conclusions and to establish their own, which are entirely opposite to his. In Dr. Duclley" discussion of his former investigation, at the Pittsburgh meeting, he said, "If you do not like my conclusions, draw your own conclusions." I have studied his last paper as thoroughly as the limited time since I received it would adruit, and have drawn some concluvions which I will first state, and then attempt to demonstrate. Briefly stated, my conclusions are: lst, That as far as these 64 analyses reveal anything of service to railmakers and cotsumera, it is that within the following chemical and physical limits, viz., Carbon,..0.20 to 0.60 Pisovphorue ,..0.026 to 0.146 Silicon,.. 0015 to 0.480 BInnganese.......0.262 to 0 880 Phosl~horus un~ts,..20.3 to 6.72 Bending weight,. 2270 lbs. to 4260 Ibs. Drfl~ctinn,.. 13O to 190° or in other words within the limits of rienrly the whole range of the chenlical and bending testa of these 6-2 mils: the wearing capacity bears no relation at all to mrbon, to phosphorus, to silicon, to mnnganese, to phosphorus units, to bending weight or to deflection or if there is any relation between the wearing capacity and thest! six or sr!ven variables, it is so obscured by the action of other cause or variat~les not yet known, that such relation cannot be expressed by any practical formula. 2d. That the difference in wearing capacity of these 64 rails was not due to unrbon, to phosphorus, to silicou, to manganese, or to anj combinntion of these four elements, but that it was due to some other cause or cornbination of causes, of which Dr. Dudley's whole iuvestigtion furnishes 11s no clue whatever. A few of the nlarry possible causes I lnay name : sulphur, copper, oxide of iron inclossl air or other gases, orerblowing, underblowing, oyrhaiting, undcrIreatinp, too hot-finishing, too cold-finishing, cold-straightening, toc great or too litkle rductiun hlu the rail to the ingot, or the portion

Jan 1, 1881

By C.R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

By C. R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

C. P. SANDBERG, LONDON, ENG : † I think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr., Dudley, for spending so much time and money in order to solve an important question ; nor are we less indebted to the public spirit which leads them to impart the experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; but even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails-tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper, a paper which follows very much upon the same lines of argument as the first read three years ago, upon which I have previously touched in my paper on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken more pains to prove that he was correct in his first formula for the best chemical composition of steel rails. But I have seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by samples. If Dr. Dudley would only give up his formula, which would not suit any country-not even America- * For the convenience of members it has bees thought best to insert the continuation of this discussion at the Virginia meeting in tide place, rather than to delay its permanent publication until the issue of Volume X, Transactions, where it would properly belong. T. M. D., Sec'y, † Sent to the secretary in manuscript.

Jan 1, 1881

With only one certain exception coal was never used by the Indians, before white men came to America, for any purpose except as an ornament or for paint. Within the past few years it has been discovered that the Hopi Indians in Navajo County, Arizona, used lignite for burning pottery, about 1000 A. D., as dated by tree rings. They were able to obtain a clear color in their ware that could not be obtained with brushwood fires. The coal was mined by hammers from outcrop openings, some of which can still be seen, and the tools used have been found in them.1 (See also p. 376.) Small figurines made of splint or cannel coal have been found at various localities in western New York, in Ohio and possibly other places, evidently made for ornaments. There is no reason to think they are of any greater age, if as old, as that mentioned above. Some crushed coal was used by the Indians as a black pigment in painting themselves, but apparently the eastern Indians never used coal for any other purposes. Some think that several tribes of Indians in the Northwest, along the Missouri, used coal as fuel, the basis being a statement attributed to Radisson about 1660. In the Jesuit Relations of 1659-1660 it was stated that Radisson anti Groseilliers had just returned from a visit to Lake Superior and beyond. "In the country of the Poualak, which means 'warriors' they say `as wood is scanty in supply and small in size in their country, nature has taught them to make fire with coal from the earth (charbon de terre) and to cover their cabins with skins.'"2 This statement was only hearsay with the good fathers, and the reputation for veracity of the two explorers is not of the best, and it is extremely probable that instead of coal they used turf, dry grass or buffalo chips. In fact in Radisson's Voyages' he does not mention coal at all in his account of the third voyage, when he was supposed to have seen it used. His accounts of his travels are badly mixed, and he and his companions were much better travellers than narrators. None of the early travellers up the Missouri River saw any evidence even then that the Indians were familiar with the use of coal. In the writer's opinion it is unlikely that coal was used as stated by the Jesuits.

Jan 1, 1942

The resin-in-pulp (RIP) ion exchange process was originally conceived by the Atomic Energy Commission in the early 1950's. However it was developed to commercial success by the Anaconda Co. at its 3000-tpd ore processing mill in Grants, N. M. Essentially, the Anaconda mill's crushing, grinding and acid leaching operations are the same as at the nearby Kerr-McGee mill, except that Anaconda uses manganese dioxide instead of sodium chlorate as oxidant during acid leaching. The real differences between the two mills become evident when considering how Anaconda treats its leached materials.

Jan 8, 1974