Search Documents

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

The one hundred and twentieth meeting of the Institute was held at Chicago, Sept. 22 to 26, inclusive, and was in every way success although the steel strike against the United States Steel Corpn. prevented many engineers from attending the steel session and made necessary the annulment of the trip to the steel works at Gary on Tuesday. All of the meetings were held at the Congress Hotel, with the excep-tion of the session on Non-ferrous Metallurgy which was held at the Coliseum where the Fifth National Exposition of Chemical Industries was in progress. This session was a joint one with the American Electro-chemical Society. The total attendance, as shown by the registration, was 850.

Jan 11, 1919

By Frederick G. Coqueron, Joseph E. Pogue

FOR a number of years, the Department of Petroleum Economics of The Chase National Bank has been conducting a study of the capital employed in the petroleum industry. The technique followed is that of combining and summarizing the available financial and operating data for a group of thirty representative oil companies, doing about two thirds of the domestic business of the entire industry. This paper presents the results of the findings for the year 1943, and supplements the survey, "Sources, Disposition, and Characteristics of the Capital Employed by Thirty Oil Companies During the Nine-Year Period, 1934-1942," presented before the Petroleum Division of the American Institute of Mining and Metallurgical Engineers on Feb. 24, 1944, and also published as a pamphlet by The Chase National Bank.

Jan 1, 1944

The Board of Directors, at its meeting on March 22, 1918, extended an invitation to the American .Institute of Metals to become the Institute of Metals Division of-the American Institute of Mining Engineers in accordance with the terms of By-Law VII. This invitation was presented to the membership of the American Institute of Metals for letter ballot, and, at the meeting of the Board of Directors of the American Institute of Mining Engineers on April 26 191 ,it-was reported that the replies had been in favor of accepting the invitation. The American Institute of Metals therefore becomes a division of this Institute and the members thereof are entitled-to all privileges of regular

Jan 6, 1918

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

Jan 1, 1913

By George Straghan, Ralph Thomas

OIL production in Kentucky in 1941 was 5,191,024 bbl., one barrel less than in the preceding year. The total completions for the state numbered 714, of which 256 were gas Manuscript received at the office of the Institute Feb. 26. 1942. * Geologist, .Kentucky Weal Virginia Gas Co., Ashland, Ky. † Geoloneist. Inland Gas Co.. Ashland. Kv. producers, 220 oil wells, and 227 dry holes. The total number was 95 more than in 1940. No new important oil or gas pools were discovered. The number of dry tests was large, although many of the dry holes could be considered wildcat tests. In western Kentucky, 365 wells were drilled, of which 145 were oil producers,

Jan 1, 1942

By Ralph Thomas, George Straghan

OIL production in Kentucky in 1941 was 5,191,024 bbl., one barrel less than in the preceding year. The total completions for the state numbered 714, of which 256 were gas Manuscript received at the office of the Institute Feb. 26. 1942. * Geologist, .Kentucky Weal Virginia Gas Co., Ashland, Ky. † Geoloneist. Inland Gas Co.. Ashland. Kv. producers, 220 oil wells, and 227 dry holes. The total number was 95 more than in 1940. No new important oil or gas pools were discovered. The number of dry tests was large, although many of the dry holes could be considered wildcat tests. In western Kentucky, 365 wells were drilled, of which 145 were oil producers,

Jan 1, 1942

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

By R. M. Asimow, J. J. Svitak

Tile crilical resoll,r,d shear stress, CRSS, for slip of slow1y cooled Ag-All single crystals was measured at 201K. Tlze importance of short-range order and Suzuki sogregalion was inrestigated by deter~rlining llze ciic.cl of quenching on the CRSS. Thr obserz.ed rfrtenching effects were generally small and indicate that short-range ordcr and Slczuki srgregation do no1 account for n significant portion of the solid-solution strengthening in this system. However, all alloys slzozcwi yield drops ulhich rilere heat- lreat nrenl-sensiline THERE have been a number of mechanisms proposed to explain alloy strengthening in the Ag-Au system. The effectiveness of some of the proposed mechanisms, especially those that depend on Suzuki segregation1" or on short-range order,2-6 SRO? should be strongly dependent on heat treatment. Since internal friction investigations in this system indicate that there is stress-induced order,' we must also consider the possibility of local atomic rearrangement or short-range ordering in the stress field of a dislocation. There is not complete agreement whether these mechanisms should be most effective in raising the flow stress, in causing yield drops. or some combination of these two effects. This work was undertaken to determine the effects in the Ag-Au system of mechanisms that depend on segregation or order by using known but drastically different cooling rates following a high-temperature treatment. By comparing the critical resolved shear stress, CRSS, for slip measured after a very slow cool and again after a fast cool (quench) of the same crystal, it is possible to determine the effect of cooling rate on CRSS* and on yield drops. The single-crystal CRSS was determined at several compositions because there has been no data published across the phase field since the publication of room-temperature flow stress by Sachs and Weerts.' EXPERIMENTAL PROCEDURE Starting with materials of 99.999 pct purity, single-crystal specimens of random orientation 1.25 mm square by 4 cm long were prepared with 0, 10, 14, 25, 30. 50, 70. 75. 80, 90. and 100 at. pct Au. Crystals were grown in an inert atmosphere using a modified Bridgman technique with a growth rate of 1.5 cm per hr in a gradient of 3°C per cm. To obtain a maximum practical degree of SRO, the crystals were cooled at a rate of 275'C per hr to about 310°C and then cooled at 6°C per hr to approximately 200°C. Specimens were tested in tension immersed in an alcohol bath at -72°C (201°K) at a strain rate > = 0.003 mm"1 to determine the CRSS (7). The activation volume of several crystals was determined from the flow stress increment (72 - T1) for a tenfold increase in strain rate. The total shear strain varied from 0.05 to 2.3 pct but was generally less than 0.4 pct. After testing, each crystal was then held at 500°C for 10 min, quenched into brine at -35°C and. after storage at -71°C for 1 day, retested in tension using a procedure identical to that of the first test. The quenching apparatus, see Fig. 1, was designed to enable accurate temperature control and rapid quenching while preventing specimen contamination and accidental deformation. Test data from a specimen with a fine thermocouple spot-welded to it indicated a cooling rate of 104C per sec. The relatively low heat-treatment temperature was chosen to minimize quenching defects caused by a large vacancy

Jan 1, 1970

By Willard S. Morse

The ores of the district are treated at this mill by the lixiviation process, consisting of drying, crushing, chloridizing-roasting and lixiviation by hyposulphite and Russell solutions. Gas is used as fuel for both drying and roasting, The gas-plant consists of two- Taylor revolving-bottom gas-producers, one 6 feet in diameter for the ore-dryers, the other 7 feet in diameter for the Stetefeldt furnace. The producers were made by Messrs. R. D. Wood & Co., Philadelphia, who also furnished the

Jan 1, 1893

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, 1871 1 3 2 Bethlehem, Pa August, 1871 1 10 3 Troy, N Y November, 1871 1 13 4 Philadelphia, Pa February, 1872 1 17 5 New York, N Y May, 1872 1 20 6 Pittsburg, Pa October, 1872 1 25 7 Boston, Mass February, 1873 1 28 8 Philadelphia, Pa May, 1873 2 3 9 Easton, Pa October, 1873 2 7 10 New York, N Y February, 1874 211 11 St Louis, Mo May, 1874 3 3 12 Hazleton, Pa October, 1874 3 8 13 New Haven, Conn February, 1875 3 15 14 Dover, N J May, 1875 4 3 15 Cleveland, 0 October, 1875 4 9 16 Washington, D C February, 1876 4 18 17 Philadelphia, Pat June, 1876, 5 3 18 Philadelphia, Pa October, 1876 5 9 19 New York, N Y February, 1877 5 27 20 Wilkes-Barre, Pa May, 1877 6 3 21 Amenia, N Y October, 1877 6 10

Jan 1, 1917

[ ]

Jan 1, 1942

By Bernard MacDonald

Of the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the cluantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted, the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide,plant than that of being economical and corlvellient containers or receptacles for holding the pulp, solutiou, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to dolids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge; that is, each solid particle of the pulp, whether it be of' 180- or 400-mesh size, should be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertaiued to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Jan 1, 1912

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By K. D. Sheffler, R. W. Hertzberg, R. W. Kraft

The Ni-Ni,Ti lamellar eutectic alloy responds to unidirectional solidification by alig-nment of the platelets of the two phases roilghly perpendicular to the moving solid-liquid interface. X-ray diffraction and zetallographic experimenls show that the following cryslallographic relationships exist in the directionally solidified ingots: lamellar interface w [0001] Ni3Ti 11 (111 }Ni local growth direction (1120) Ni3Ti n (110) Ni These relationships are rationalized on the basis of the crystallography of the constituent phases. In recent years researchers in several laboratories have shown that an aligned or "controlled" micro-structure can be produced in many binary eutectic alloys by forcing the alloy to solidify unidirectionally in an elongated crucible.'-3 It also has been found that a unique crystallographic relationship often develops between the two phases in such a structure.4, 5 Since a parallel arrangement of phase particles in an alloy should, and, in many cases, does, produce unique and highly anisotropic properties, the alloys so produced are of potential interest in a variety of applications. Studies of these alloys are also of interest at the academic level because they help to improve our basic understanding of the way in which metals solidify. This paper reports the metallographic and crystallographic structure of another of these alloys—that between nickel and Ni3Ti. In a separate paper, hot tensile and stress rupture properties as well as deformation and fracture behavior of the same alloy are discussed.19 EXPERIMENTAL DETAILS AND RESULTS General Characteristics of the Eutectic Reaction. Several small exploratory Ni-Ti melts were made to resolve a conflict in Hansen6 over the eutectic composition. The alloy containing 16.4 at. pct Ti, Fig. 1, appeared metallographically to be closest to the eutectic composition, although small dendritic patches of proeutectic nickel are present. The eutectic morphology is lamellar and appears quite sharp and angular, indicating a strong influence of crystallographic factors upon the microstructure. Some of the eutectic nickel platelets are continuous with the primary phase, whereas in hyper eutectic melts a "halo" of nickel generally surrounded the proeutectic inter-metallic platelets, indicating that nickel is the nucleating phase in this eutectic reaction. Extensive precipitation of Ni3Ti has occurred in the primary nickel phase in a Widmanstatten pattern which makes the dendrites difficult to differentiate from the eutectic mixture. This phenomenon may account for discrepancies among the eutectic compositions reported in the literature. The sloping solvus line bounding the nickel primary solid solution explains the presence of the intermetallic precipitate. Poole and Hume-Rothery7 report that the solubility of titanium in nickel drops from 13.8 at. pct at the eutectic temperature (1304°C) to approximately 9 at. pct at 700°C (Ni3Ti, on the other hand, melts con-gruently and exhibits essentially no solubility for nickel or titanium). Lever rule calculations based upon Poole and Hume-Rothery's phase diagram indicate an increase from 21 vol pct Ni3Ti in the eutectic mixture at the eutectic temperature to 61 pct at room temperature. Selective point count measurements of the volume fraction of eutectic Ni3Ti platelets in the eutectic microstructure yielded a value of 46 i 2 vol pct, which required extensive precipitation of Ni3Ti from the nickel solid solution onto the eutectic intermetallic platelets during cooling from the solidification temperature. Influence of Directional Solidification. Nickel bar and titanium sponge of 99.9 pct purity were induction-melted in zirconia crucibles under argon in the proportion of 13.8 wt pct (16.4 at. pct) Ti to produce 14-lb master heats which were cast into investment molds yielding 5/8-in.-diam pins approximately 10 in. long. These pins were remelted under argon in horizontal zirconia boats and unidirectionally solidified to produce 1/2-in.-sq ingots approximately 44 in. long. Details of the experimental techniques and apparatus are described elsewhere.'

Jan 1, 1970

The following is an incomplete list of members and guests who called at Institute headquarters during the period June 10, 1918 to July 10, 1918. F. C. Alsdorf, Tucson, Ariz. Emory M. Marshall, Camp Raritan, N. J. Juan F. Brandes, Santa Barbara, Cal. Jacques S. Negru, Camp Niagara, Ont. .H. Smith Clark, Kansas City, Mo. Arvid E. Nissen, High Bridge, N. J. J. S. Cunningham, Charleston, W. Va. Richard G. Place, So. Strafford, Vt. W. G. Eberhardt, Tucson, Ariz. Frank H. Probert, Berkeley, Cal. M. Eldredge, Bombay,. India. Martin A. Roudabush, Osterburg, Pa. A. D. R. Galloway, Accra, W. Africa;. P. H. Royster, Minneapolis, Minn. F. Hanst, Harrisburg, Pa. J. L. Schueler, Peoria, Ill. B. B. Hood, Chrome, N.. J. Henry B. Smith, New Britain, Conn. Paul S. King, Wilmington, Del. W. G. Sommer, Peoria, Ill. E. D. Kinney, Anaconda, Mont. A. L. Toenges, Roanoke, Va. E. W. Kohl, Jr., Philadelphia, Pa. G. D. B. Turner, Butte, Mont. James W. Love, Knoxville, Tenn. A. T. Ward, Bellefonte, Pa. Edwin A. Austin, formerly with the Yukon Gold Co., is superintendent of the Elkoro mine at Jarbidge, Nev. John W. Beard is now with the Cia Minera de Penoles, Ojuela, Dgo., Mexico, via Mapimi. R. S. Bonsib has accepted a position with the United States Emergency Fleet Corporation as District Safety Engineer, San Francisco, Cal. Albert Burch has been appointed by the Bureau of Mines to encourage the mining of chrome. F. B. Caldwell is working for the U. S. Bureau of Mines, under Albert Burch, in the investigation of chromite deposits. W. A. Carlyle has taken over the duties (in addition to his own) formerly assigned to E. P. Mathewson with the British America Nickel Corporation, at Sudbury, Canada. R. M. Catlin received the honorary degree of Doctor of Science at the recent commencement of Rutgers College, New Brunswick, N. J. S. K. Dahl is giving up his position as mill superintendent with the Messina Mines, which have been suspended, and is returning to this country. Algernon Del Mar has become manager of the Techatticup mines, El Dorado Canyon, Nev. Robert Dye has succeeded D. L. Forbes as manager of the Teck-Hughes at Kirkland Lake, Ont., Canada. J. O. Elton, superintendent of the Anaconda company's electrolytic zinc plant at Great Falls, Mont., is doing special work with the U. S. Bureau of Mines. R. B. Caples takes charge of the plant in his absence. George H. Gibbs has resigned his position as engineer at Messrs. T. & 1. Bradley & Sons, Ltd., Darlaston blast furnaces, Darlaston, and is now located at "Belmont." Litchfield Road, Rushall, Walsall, England. William D. Gordon, for the past 7 years manager of The Mine & Smelter Supply Co. at El Paso, has been elected president of Camphuis, Rives & Gordon,. Inc., and has opened American headquarters for the company at 81 New Street, New York, N. Y. E. Harms, for the past 16 years inn charge of metallurgical operations of the Torreon, Mexico; lead and copper smelter, has resigned and is now located at El Paso, Tex.

Jan 8, 1918

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

William R. Walker, assistant to the president of the U. S. Steel Corpn., died at St. Luke's Hospital, New York, on Dec. 20, 1922. He was born at LaPort, Ind., Nov. 26, 1857, and his whole career has been closely identified with the iron and steel industry. His first employment was with the North Chicago Rolling Mill Co., Chicago; then he was appointed chemist for the Crown Point Iron Co., at Crown Point, N. Y.; and later he was works superintendent for Spang, Chalfant & Co., of Pittsburgh. He was early associated with Robert Forsyth, the well-known engineer who constructed the South Chicago works of the North Chicago Rolling Mill Company. Prior to 1890, Mr. Walker was works manager for the Union Steel Co., and upon organization of the Illinois Steel Co. he became general manager of its South Chicago works. At the time of the formation of the U. S. Steel Corpn., in 1901, he was appointed assistant to the president, which position he held until the time of his death. Through the technical staffs and committees of the Steel Corpora tion, Mr. Walker had an excellent opportunity to study and direct the development of mechanical methods for coal mining, coal washing, beehive coking, including the collection and recovery of its byproducts, and to interest himself in byproduct coke ovens, and the design and operation of processes for the coking of special coal mixtures. He also brought his experience to bear on the design, construction and operation of the blast furnace and its appurtenances, as well as the bessemer, open-hearth and electric steel processes. Incidentally, he was interested in microscopy and metallography, and was familiar with the manufacture of products related to the iron and steel industry, such as tin, zinc, sulfuric acid and many other substances. Mr. Walker had the remarkable faculty of being able to discuss and conduct investigations in practically any technical branch of the ferrous industry. In the words of President James A. Farrell, "Mr. Wdker was a man of keen mental attainments and possessed an exceptional knowledge of the iron and steel industry, from both the scientific and the practical

Jan 1, 1923