Search Documents

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By Charles S. Barrett, Robert F. Mehl

It is generally understood by workers in the field of the crystal structure of metallic alloys that terminal solid solutions are of two types, the substitutional and the interstitial. In reviewing the literature, the work of Weissl on the crystal structure of the alpha copper-tin alloys was encountered, in which a new type of terminal solid solution was proposed. In brief, Weiss' findings showed that the density of the alloys calculated from the side of the unit face-centered cube on the assumption of simple substitution—that is, with four atoms to the unit face-centered cell—was much higher than the density measured directly. It was suggested that the assumption of four atoms to the unit cube is not valid for these alloys, and that each unit cube contained less than four atoms; in other words, that one tin atom replaces more than one copper atom, leaving some atomic positions unoccupied. Such a structure, if verified, would have far-reaching significance in the study of the crystal structure of metallic alloys. It would indicate a complexity in terminal solid solutions not hitherto suspected and might encourage work leading to the discovery of other alloys of the same type, and perhaps to types intermediate between it and the two recognized types. It is of importance, therefore, to reinvestigate these alloys with respect to the type of solid-solution structure obtaining therein. Materials and Experimental Method The alloys were prepared from electrolytic copper cut directly from the cathode and the high-purity tin furnished by the U. S. Bureau of Standards for the calibration of thermocouples. No analyses for impurities of these materials or of the finished alloys were made, since such impurities as might be present could have only a wholly inappreciable effect upon the data obtained and the conclusions drawn. The alloys were made by melting the weighed copper charge in a graphite crucible under a KCl-LiC1 flux with later additions of NaC1, using induction heating. When the copper was melted the weighed portions of tin were

Jan 1, 1930

By Vincent P. Gianella

Barite deposits are of widespread occurrence in Nevada but there are few producing properties; most of the latter are in northern Nevada. The production of the state is small at present-in the neighborhood of 15,000 tons annually-but is steadily increasing. The barite occurs in veins and also as replacement deposits in limestone. The bulk of the production has come from the replacement deposits. It is thought that the barite was deposited from rising hot waters similar to-and probably contemporaneous with-those responsible for some of the metallic ores of the state. This paper discusses only the deposits in northern Nevada. THE commercial mining of barite did not begin in Nevada until 1916 but although the production has been small there has been a rapid increase in tonnage during the past several years. Barite is widely distributed in the state and production comes from at least nine of the seventeen counties. Apparently this is not generally known, as only two counties are mentioned in a recent publication6 dealing with barite. The increase in output is due largely to recently discovered barite deposits in northern Nevada. The principal production has come from the northern portions of Lander and Eureka counties; smaller amounts from Elko County. The discussion in this paper is confined largely to the deposits in these counties. Most of the producing area is tributary to the Western Pacific and Southern Pacific Railroads, whose tracks lie along the Humboldt River. Barite is known from other northern counties but so far the production has been small. The output has come entirely from veins and replacement deposits, the latter largely in sedimentary rocks. In general, the barite from veins is white; that from the replacement deposits usually is dark gray to black, although some is light gray or white. Most of the veins contain sulphides and many barite-bearing veins have been worked for their content of base or precious metals. PRODUCTION The recorded production in Nevada to the end of 1938, according to the U. S. Bureau of Mines,3 is 66,424 short tons, of which 57,157 tons

Jan 1, 1940

By L. G. E. Bignell, E. A. Hanson, J. O. Lewis

There was a general upward trend of all petroleum activities in Oklahoma during 1933, especially in the last quarter, though the average price for crude oil for the year was below 1932 and overproduction in East Texas demoralized conditions for several months. As the Federal Agencies established under the National Industry Recovery Act began to function conditions in Oklahoma were visibly affected and production of "hot oil" from Oklahoma City field practically ceased. More oil wells were completed, six new fields discovered, extensive geophysical prospecting carried on in many parts of the state, and an increased amount of clean-out and reconditioning work done in older pools during the past year. To increase quantity and rate of recovery of oil many wells producing from limestone formations were treated with hydrochloric acid. The Oklahoma City field had a reported production of 66,984,570 bbl. of oil during 1933, or almost exactly twice the amount reported for 1932. Potential tests and other indicators show that the wells are rapidly approaching the stage where mechanical lift must be applied to all of them, including the wells in the Wilcox sand zone. The major pipe-line companies serving the oil fields of Oklahoma have been anxious to make connections to all wells during 1933 and have indicated a willingness to accept all oil available. The amount offered has been restricted by proration orders, but the state did produce 178,356,-449 bbl. during the year, an increase of about 18.6 per cent over 1932. This increase was practically all due to the greater demand for Oklahoma City oil, as all other pools of any importance showed loss in production or very small gains last year. The U. S. Bureau of Mines' laboratory reports the lubricating distillate content of Oklahoma City crude from Arbuckle and Lower Simpson formations about 17 per cent by volume. East Texas oil is reported to contain about 5.6 per cent lubricating distillates. The desire of the transportation companies to keep their equipment operating at maximum capacity and the need of some refineries for more

Jan 1, 1934

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By W. M. Yim

Experimental results are presented which indicate that transverse striations in horizontal zone-leveled Bi-Sb alloy crystals are due to irregular growth rate resulting from thermal fluctuations in the melt (Iring gowth. Thc thermal fluctutations arose from two different sources. The first type was brought about by periodic fluctuations in the furnace temperature. The second type can be attributed to turbulent therrrol conlcclion in the trzelt near the solid-liquid inteyace. Tile arrzplitlcde ond fvequency of the tetiperaticre fluctlrations vesultity from llle lhevnal con1,ecrrell. The striation spacings in Lhe crystals covvelale well with the periodicity 0.f the tempevature flueluatiors. Altliough the strialiors represenl corrlpositiozul inhoiHogeneity oh a rzicroscule, less than f.z cil. be1 S6 in Best's as deterrirzed by electron-pro be chalq'sis, the slriations roerre fbund to ILUL' no rrleusuanble effect on electical vesistirity rwr on weak field macgnetoresistance of. the Bi-Sb a1lu.y in the ternpevutue ),unge 4.Polo 300°K. DURING the course of an investigation on the horizontal growth of semimetals,' it was found that crystals of Bi-Sb alloys contained many closely spaced parallel arrays of striations. These striations occurred perpendicular to the growth direction and parallel to the solid-liquid interface. We shall refer to them as transverse striations, or just striations'', to distinguish them from lineage substructures or longitudinal striations which form parallel to the growth direction and have been known to be associated with cellular structures.' Similar transverse striations have been reported previously to occur in other materials prepared by horizontal growth: metals,4 semiconductors,5 as well as their alls. - Various methods of crystal preparation have apparently little effect on the occurrence of the transverse striations. They form whether the crystals were grown by the vertical Czochralski technique, withe1' or without'3- rotation, or by the horizontal zoning methd.- Thus, the transverse striations are not limited to any one class of materials, nor to any particular method of preparation. It is likely, therefore, that all of the observed transverse striations may have some common cause. Previously, workers agreed that periodic changes in the growth rate bring about the striations. However, no agreement exists as to the origin of the growth-rate fluctuations. Some attributed the discontinuous growth to a purely external cause, such as fluctuations in the furnace temperature, jerky motions in the crystal pulling mechanism, or a nonsymmetrical temperature distribution in the melt (in the case of crystals grown by the Czochralski technique with rtation). Others looked for the cause in some fundamental property of the growth process itself. For instance, a certain degree of supercooling is required to initiate growth from the melt. But, with further growth, the degree of supercooling decreases because of the liberation of the heat of solidification at the solid-liquid interface. Thus, crystal growth would be brought to a halt until sufficient supercooling is resotred and the cycle begins again.3'11 According to this model, periodic fluctuations in the melt temperature should exist at the solid-liquid interface. Since the periodic fluctuations in growth rate would result in changes in the segregation coefficient of solute atoms, crystals containing the transverse striations may, in some cases, show a periodic impurity fluctuation along the length, resulting in a degradation of electrical properties. The resistivity striations in doped germanium'9-10 or lnsbB are well-known examples of this microsegregation. The present work was undertaken to explain the exact origin of the transverse striations, and to assess the extent of their effect on chemical homogeneity as well as on electrical properties of Bi-Sb alloy crystals. Results from our previous study of the crystal growth of Bi-Sb alloys1 indicated that the transverse striations may arise from the temperature fluctuations in the melt during growth. This paper will show that the melt temperature fluctuations are indeed responsible for the occurrence of the transverse striations. I) EXPERIMENTAL Although the transverse striations have been observed in all slow-grown Bi-Sb alloys across the entire compositional range, we selected a composition, Big3Sbs, for the present study in view of the extensive data available on the crystal growth of this alloy from a previous study.' High-purity bismuth and antimony, both a 6-nine grade by the manufacturer's emission spectrographic analysis, were used throughout. Independent mass-spectrographic analysis showed, however, that the starting materials were more nearly a 5-nine grade. each containing metallic impurities of approximately 10 ppm atomic. In zone-leveled Big5Sb5 alloys, the total metallic-impurity content was slightly lower, about 7 ppm atomic, indicating that some degree of purification was achieved during the growth. None of the electrically active impurities, such as tin and lead (acceptors) and tellurium and selenium (donors), were present in significant quantity in undoped Bi95Sb5. Typical analysis of the undoped Bi95Sb5 alloy is shown in Table I. Nonmetallic impurities, such as carbon and oxygen, were detected, sometimes as much as 100 ppm, in both the starting materials and the zone-leveled alloys: but the data were only qualitative. Temperature fluctuations in the melt were monitored over 1 or more days by means of a 5-mil chromel-

Jan 1, 1967

By S. Sumski, M. B. Panish, R. T. Lynch

The liquidus isotherms in the gallium-rich corner of the Ga-Al-P phase diagram have been determined from 1000" to 1200°C and at I100°C the corresponding solidus isotherm was obtained. A simple thermody-namic treatment which permits calculation of the solidus and liquidus isotherms is discussed. A technique which was previously used for the growth of GaxAl1-xAs was used for the preparation of solution epitaxial layers of GaxAl1-xP and ALP. An approximate value of 2.49 i 0.05 ev for the band gap of Alp at 300°K was obtained and the ternary phase data were used to estimate a value of 36 kcal per mole for the heat of formation 0f Alp at that temperature. The Gap-A1P crystalline solid solution is one in which there exists the possibility of obtaining crystals with selected energy gaps, within the limits imposed by the energy gaps of Gap and Alp. Such crystals are of considerable interest because of their potential value for optoelectronic and other solid-state devices. Furthermore, it has been amply demonstrated for GaAs and GaP,'-7 that device, or bulk materials grown from gallium solution generally have more efficient radiative recombination than materials prepared in other ways. This presumably due to the lower gallium vacancy concentration in such material.= Small crystals of GaXAl1-xP and A1P have been grown from solution,8-10 and A1P has been grown from the vapor," but neither have previously been grown by liquid epitaxy. In this paper we present the ternary liquidus-solidus phase diagram of the Ga-A1-P system in the region of primary interest for solution epitaxy, and discuss the thermodynamic implications of that phase diagram with particular reference to the liquidus and solidus isotherms in the gallium-rich corner of the GaxAl1-xP primary phase field and to the A1-P system. Several measurements of the absorption edge of GaxAl1-xP crystals have been made and the width of the forbidden gap of A1P has been estimated from these measurements. EXPERIMENTAL The differential thermal analysis technique used to determine the liquidus isotherms and the optical measurements used in this work are similar to those described previously12 for the Ga-Al-As system, ex- thermocouples in the thermopile for added sensitivity. The materials used were semiconductor grade Ga, Gap, and Al+ The composition and temperature range at which DTA studies could be done was quite restricted. The upper temperature was limited by the chrome l-alumel thermopile to about 1200°C, and the highest aluminum concentration to about 5 at. pct by low sensitivity caused by the reduced solubility of Gap with increasing aluminum concentration in the liquid. DTA studies were not possible at 1000°C and below because of the low sensitivity caused by low solubility of Gap in the Ga-A1-P system. The cooling rate for these studies was about 1°C per min. No heating studies were done because of limited sensitivity. Supercooling probably does occur, but our experience with other 111-V systems indicates that it is no greater than about 10 to 15.c. Solid solubilities were determined by analyzing epitaxial layers of GaxAl1-xP grown from the liquid, with an electron beam microprobe. The layers were grown on Gap seeds by a tipping technique in which the layer is grown over a short-temperature range (20" to 50°C) on the seed from a solution of known composition. The tipping technique reported by Nelsson1 for GaAs could not be used, particularly for solutions containing appreciable amounts of aluminum, because of the formation of an A1203 scum on the liquid surface. A system was therefore designed, which would effectively remove the oxides mechanically, so that uniform wetting and crystal growth could occur. This tipping technique has already been described in detail." The best control over the composition of the re-grown layer was obtained when the tipping was done at a temperature which corresponded to the temperature of first formation of solid for the solution being used. Generally, therefore, a solution was prepared by adding the amounts of Ga, Gap, and A1 required to yield a solution which would be completely liquid above the tipping temperature with solid precipitating below that temperature. For most of the work reported here, the 1100°C isotherm of the ternary was used. It was generally necessary to heat the solution to 50" to l00. C above the tipping temperature to dissolve all of the Gap in a reasonable length of time. The epitaxially grown layers were used both for optical transmission measurements to aid in the estimation of the way in which the absorption edge changed with aluminum concentration, and for the electron beam microprobe analyses to provide data for the determination of the solid solubility isotherm. RESULTS AND DISCUSSION Liquidus Isotherms in the Ga-A1-P Ternary Phase Diagram: Thermodynamic properties of the system. The only thermal effect studied in this work was that

Jan 1, 1970

By A. R. Calawa, T. C. Harman, M. Finn, P. Youtz

A study has been made of the growing, annealing, and diffusion parameters in PbSe, Pb1-ySnySe, and Pb1-xSnxTe. Single crystals of these materials have been grown using the Bridgman technique. For all of the above materials the as-grown crystals are p type with high carrier densities. To reduce the carrier concentration and increase the carrier mobility, the samples are annealed either isothermally or by a two-zone method. From isothermal anneals, the liquidus-solidus boundary on the metal-rich side of the stoichiometric composition has been obtained for some alloys of Pb1-xSnxTe and on both the metal- and seleniunz-rich sides for PbSe and alloys of Pbl-ySnySe. In Pbo.935 Sno.065 Se carrier concentrations as low as 5 x1016 Cm-3 and mobilities as high as 44,000 sq cm v-1 sec-1 at 77°K have been obtained. Inter diffusion parameters mere also studied. The ddiffusion experiments mere identical to the isothermal or two-zone annealing experiments except that the samples were removed prior to complete equilibration. The resulting p-n junction depths were determined by sectioning and thermal probing. Inter diffusion coefficients for various temperatures were calculated for both PbSe and Pb0.93Sn0.0,Se. RECENTLY, there has been considerable interest in the PbTe-SnTe and PbSe-SnSe alloys with the rock salt crystal structure. The unusual feature of these systems is the variation of energy gap EG with composition. Several investigations1-3 have shown that EG for the lead chalcogenides decreases as the tin content increases, goes through zero, and then increases again with further increase in tin content. The possibility of obtaining an arbitrary energy gap by selecting the composition is an especially attractive feature of these alloys for applications involving long-wavelength infrared detectors and lasers. In addition, some unusual magneto-optical, galvanomagnetic, and thermomag-netic effects should occur for alloys with low band gaps. If uncompensated low carrier density crystals can be obtained, then a small carrier effective mass, a large dielectric constant, and the resultant high carrier mobility should yield enormous effects at low temperature in a magnetic field. The relative variation of the energy gap with pressure should also be very large for these low gap materials. The primary purpose of this paper is to provide some information concerning the preparation of low carrier concentra- tion, high carrier mobility, and homogeneous single crystals with a predetermined alloy composition. I) DETERMINATION OF ALLOY COMPOSITIONS In all of the work described in this paper, the composition of lead and tin chalcogenides in the alloys was determined by electron microprobe analysis. Separate X-ray spectrometers are used to make simultaneous intensity measurements of the Pb La1 and Sn La1 lines emitted by the sample under excitation by a beam of 25 kev electrons focused to a spot about 2 µm in diam. These intensities are compared to the intensities of the same lines emitted by standards under the same conditions. The standards used are the terminal compounds of each pseudobinary system, i.e., PbTe and SnTe for Pbl-xSnxTe alloys, PbSe and SnSe for Pbl-ySnySe alloys. The composition of the sample is then obtained from theoretical calibration curves which relate the weight fractions of lead and tin in the alloy to the measured ratios of X-ray intensities for the sample and the standards. The lead and tin calibration curves for each alloy system were calculated by using corrections for backscattered electrons,4 ionization,5 and absorption,6 and assuming that the atom fraction of tellurium or selenium in the sample and standards is exactly +. Results obtained by using the microprobe are in good agreement with those obtained by wet chemical analysis. II) CRYSTAL GROWTH FROM THE VAPOR Early work on the vapor growth of PbSe was carried out by Prior.7 He used small chips of Bridgman-grown single crystals as the source material and frequently converted the whole charge of a few grams into one crystal. In the present work, vapor growth occurred using a metal-rich or chalcogenide-rich two-phased alloy powder as the source material. Small, nearly stoichiometric crystals are formed on the walls of the quartz tube. The procedure will now be described in detail. Initially, a 100-g charge containing (metal)o.51(chalco-genide)o 49 proportions or (metal)o.49(chalcogenide)o. 51 proportions of the as-received elements in chunk form are placed in a fused silica ampoule. After the ampoule is loaded, it is evacuated with a diffusion pump and sealed. The sealed ampoule is placed in the center of a vertical resistance furnace. The region containing the ampoule is heated to about 50°C above the liquidus temper-ature for the particular composition used. After about one-half hour at temperature, the elements are reacted and the molten material homogenized. The ampoule is quenched in water. The quenched ingot is crushed to a coarse powder for vapor growth experiments and to a fine powder for the isothermal annealing experiments which are discussed in a later section. Vapor growth experiments were carried out using the powdered, metal-rich or chalcogenide-rich alloys

Jan 1, 1969

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By G. S. Cole, H. Biloni, G. F. Bolling

An experimental investigation of sovlze low .melting point alloys sJtows that a substvucture of isolated depressions can be the first manvestation of constitutional supercooling on solid-liquid interjaces veuealed by decanting. Electron-tni cvop vobe and wletallo gvaplic esanzinations, in tlze bulk belzind the interjace, oj the segregation associated with these isolated areas substantiate tlzei&apos;v depressed nature, since a solute of ko < 1 is enriched, and a solute of ko > 1 depleted. In contrast, the pox structuve, a set of projections often veported in the literature, leaves no trace oj. segvegation. These obserl;atims, accovlrpanied by a brief review of recent literature, point to inconsistencies between experirrental obsevvation and the idea that the fornzation of a projection is a causal step in the development of a cellular substructure. An argument is presented to show instead how it is plausible for substantial depvessiom to form in the pvesence of constitutional supercooling at dislocations threading the solid-liquid interjace. THE development of constitutional supercooling during growth from the melt leads to the formation of the cellular solidification substructure. This well-founded association between structure and instability has been basic in understanding cellular substructure and micro segregation; however, the initial formation of structure seems unclear. Rutter and Chalmers,&apos; in definitive experiments and theory, noted that in the presence of constitutional a planar interface might break down: "resulting in the formation of a small projection on an initially plane or uniformly curved interface." That is, the breakdown from a planar to a cellular interface was implied to be initiated via a projection into the unstable liquid. Later, Walton et (11. found that a structure of isolated projections, termed "pox", appeared at solid-liquid interfaces decanted under growth conditions near the onset of constitutional supercooling; the pox were taken as the indication of the instability promoted by the supercooling. Tiller and Rutter4 in their extensive work studied the shape transitions at decanted interfaces which were generally observed to proceed as— pox, "irregular cells", elongated cells, regular (hexagonal) cells, and so forth. The pox varied in size from lo-&apos; to 1CT4 cm, and tended to disappear as cells increased in number and regularity, but as noted,4 the first real array of cells did not seem to be a development from the pox. In fact these authors implied a lack of connection because they stated that the pox are denser on "irregular cells", and as cell boundaries increase in number (i.e., the cells become smaller) there is less need for the pox which do dis- appear. Thereafter, most authors dealing with either experiment or theory have accepted the reality of pox and have used them as a criterion for the onset of constitutional supercooling. In contrast, Spittle, Hunt, and smiths have now suggested that pox are irrelevant artifacts comprised of such things as entrapped oxide. This proposal invokes the observations of weinberg6 and chadwick7 each of whom have shown that the act of decanting leaves a residual liquid on a decanted interface; the remnant solid layer of the order 10 p may thus contain particles that might have been transported from the external surfaces, or elsewhere, during decanting. With the incentive of this suggestion,= some further experiments and a reexamination of the literature have been conducted, in order to question the validity of pox as evidence of an instability and to examine the initial development of the cellular substructure. 1) EXPERIMENTS Single crystals of zone-refined tin (-99.9999 pct) were grown from the melt in a controlled fashion with various, small concentration additions of lead and antimony, for which ko < 1 and > 1, respectively. The crystals were decanted at conditions near the onset of constitutional supercooling and were thus appropriate for observation of slight perturbations. It was possible to observe two types of small departure from smooth or "planar" interfaces in both cases of lead or antimony additions. Some were projections and others, if in regular array of any type, were depressions. The crystals were etched with suitable reagents progressively dissolving the decanted interface surface; projections left no record, but depressions were continuously associated with spotlike areas contrasting with the rest of the interface. Traverses were made with the beam of an electron microprobe across the regions of contrast; with lead addition the persistent spots were lead-rich, and with antimony addition the persistent spots were antimony-poor. This is consistent only with a dominant role for depressions, because if the projections had left spots but were incorrectly catalogued, a reversed observation should have been made; that is, the Pb(ko < 1) should have been depleted and the Sb(ko > 1) enriched. In the work of Cole and inegard, and elewhere, regular arrays of structure associated with the initial stage of instability have been shown, in photographs and represented as pox or projections. We believe this to be erroneous, by inference, since whenever a regular array was observed, in the present examination, it consisted of depressions, regardless of the nature of the solute, ko 1. Fig. 1 is reproduced8 as an ideal example of the possible optical illusion involved; the observer can satisfy himself from the distribution of illuminated areas that the markings are depressions. Fig. 2 from the present investigation is an interference photograph of an interface similar to that in Fig.

Jan 1, 1967

By R. G. Wayland

SINCE the installation at Kropfmuehl, Bavaria, of a modern flotation concentrator in 1938, the flake and fine graphite from the Passau area can now be delivered in about any normal specified carbon content of any size range up to a flake averaging about 0.7 mm. The graphite finds a wide German and export market for crucible manufacture, pencil leads, dry cells and other uses. A controversy over the origin of the graphite deposits is being resolved in favor of syngenesis rather than epigenesis. The syngenetic theory is newly supported by the yet unpublished work of Hartmann of the Bavarian Geological Survey. Development work and exploration for graphite in the area may be changed in direction as the syngenetic theory is accepted. Crystalline graphite is produced in the area east of Passau near the junction of Germany, Austria and Czechoslovakia, as shown in Fig. 1. This is the only graphite area of importance in Germany, and Gra-phitwerk Kropfmuehl AG is the only operating firm in the area. The plant and mine are located at Kropfmuehl near Hauzenberg, Kreis Wegscheid, about 10 miles east of Passau. A narrow gage railway from the mine connects with the German Railway at Schaibing Bahnhof. The Pfaffenreuth mines date from about 1730. Until the early 20th century mining operations were carried out in a haphazard fashion. During World War I graphite mining and milling was increased, since it had to cover almost all of the crucible needs of the Central Powers. Between the wars some 11 mines were operated by two large and several small companies, but under the Nazis these were consolidated by 1938 into the Kropfmuehl enterprise. Kropfmuehl built a modern flotation mill to treat its own ores and small amounts of custom ores and tailings from the area. Since Graphitwerk Kropfmuehl AG was an I.G. Farbenindustry subsidiary, it has been under Military Government Property Control and probably will be sold to private German capital. Geology The country rock of the graphite area is part of the "kristallines Grundgebirge," the series of old gneissic and schistose rocks that constitutes the bed rock of most of the Bohemian basin and rims the Sudeten-land. The gneissic rocks of the graphite area are considered to have been metamorphosed during the Carboniferous period. They are bordered on the north by granite stocks and penetrated by numerous smaller granite and pegmatitic intrusive rocks, as shown in Fig. 1. The gneiss is classed as a micaceous, coarse-grained cordierite gneiss by most investigators. It is much metamorphosed by the granite, particularly in the north near the larger granite bodies. Interbedded in the gneiss are the graphite seams and lenses, and also beds and lenses of crystalline limestone containing disseminated graphite in noncommercial quantities. The gneiss, together with the included graphite and limestone seams and lenses, is cut and displaced by a number of granite sills of medium to fine grain and by a large number of diorite lamprophyre dikes and a few syenite-pegmatite dikes. The lamprophyre dikes are of various mineral compositions and textures, but many are banded and richly impregnated with pyrite; while the syenite-pegmatite dikes are coarse-grained with good crystals of titanite, pyroxene, uralite and other green amphiboles. Most investigators and the miners speak only of diorite and granite dikes cutting the graphite seams. The diorite dikes are later than the granite and some of the faulting, as is evident from Figs. 1 and 2. Individual graphite seams and lenses may be mined for thicknesses of several feet up to several scores of feet, and for distances of several hundred feet. The aggregate thickness of a series of some 20 seams of graphite, limestone and interbedded gneiss at Kropfmuehl is stratigraphically about 450 ft. Laterally, the graphite in a seam may pinch out or grade into crystalline limestone. Graphite crystals also are found disseminated in the gneiss itself, although in unmineable concentrations. The faults that cut the graphite seams carry graphite for some feet or tens of feet away from the seams, apparently mechanically. Similarily, the graphite lenses themselves often contain mechanically introduced inclusions of wall rock, probably from flowage during folding. Graphite crystals make up 10 to 30 pct of the fresh, mineable graphite lenses at Kropfmuehl, averaging about 20 to 25 pct after hand-sorting by the miners. In weathered lenses, the graphite concentration is said to be as high as 50 pct. The associated primary and hydrothermal minerals are dom-inantly feldspar and calcite, plus quartz, pyrrhotite, pyrite, biotite and occasional garnet, hornblende, sphalerite and galena. Associated secondary minerals include kaolin, nontronite, mangano-oxide-silicates (mog), adularia and chlorite. The superimposed suite of siliceous cementation minerals present consist largely of opal, chloropal, chalcedony, jasper, and hyalite. The kaolin is of special interest since it too was mined as early as 1730 and was used in the well-known Nymphenburg porcelain from 1756 on. The kaolin is derived from the gneiss and the syenite pegmatites. The crystals of graphite vary in size within a given seam, but in seams more than a mile away from the granite on the north the average crystal-linity is less coarse, lowering the commercial value. The lenses in the Kropfmuehl-Pfaffenreuth area are the most developed, and are the only ones with deep workings now accessible. Other similar crystalline graphite lenses are known from older workings at Habersdorf, Oberoetzdorf, Ficht, Diendorf, and

Jan 1, 1952

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may &apos; be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By P. W. Gilles, B. D. Pollock

THE pioneering work of Steinitz1 and Steinitz, Binder, and Moskowitz2 has shown conclusively the existence at high temperature of two additional phases in the molybdenum-boron system and thus brings to a total of six the number of structures appearing in this system. To the structures Mo2B, MOB, and Mo2B5 they have added MO3B2, a new -MOB form, and have shown that MOB,, which has the same range of composition as Mo2B5, is only a high temperature structure of the latter. This solid solution, interestingly enough, includes neither of the compositions corresponding to the stoichiomet-ric compounds, MOB, or Mo2B5, but rather at all temperatures has intermediate values of composition. These workers have also, in the course of their work, measured melting points, transition temperatures, eutectic and peritectic points in the system and have shown that Mo3B2, because of its dispro-portionation at low temperature to Mo2B and MOB, is stable only in a limited high temperature range. During the course of the present work on the vaporization properties of the molybdenum-boron compounds, a few transition temperatures were observed. When the report of the other workers appeared, it was decided to repeat, in part, their study of the system. As a result, considerable evidence has been obtained that substantiates the specific kinds of melting processes they report as well as the general features of their diagram. However, a marked difference was found between the temperatures they report and the ones observed in this study, with the latter being higher. The purposes of this paper are to present the evidence obtained in this laboratory that verifies their diagram of the system, to give some important temperatures in the system, to compare them with those previously published, and to seek an explanation of the difference. Samples The metal starting material was 400 mesh molybdenum powder with a purity stated by the manufacturer to be 99.9 pct. The initial treatment, designed to remove volatile contamination, consisted of heating in a vacuum for 10 min to a temperature of from 800" to 1000°C during which a loss of 0.3 to 0.4 pct occurred. An assay following this treatment showed it to be 99.4 pct pure, with the principal impurity probably being oxygen. The boron starting material was obtained from the Cooper Metallurgical Laboratories and the Fair-mount Chemical Co. as 325 mesh powder with manufacturers&apos; analyses of 99 pct or better. Initial treatment consisted of heating in molybdenum in a vacuum at about 1700°C for 10 min. During this time a loss of 3.5 pct occurred. An assay following this treatment showed the different samples to have purities ranging from 95.5 to 99.0 pct with iron and carbon as the principal impurities. Following the initial treatment, the elements were combined to form stocks of Mo2B and MOB by heating pressed mixtures in a vacuum to 1100" to 1200°C to accomplish reaction and to 1500" to 1900°C for a few minutes to evaporate the more volatile impurities. Analysis of the two compounds for boron by a modification of the method of Blumenthal3 and for molybdenum by the lead-molybdate method indicated them to have purities greater than 99 pct. The individual samples to be studied had compositions in the Mo2B-MOB range and consisted of mixtures of the stock compounds. Procedure As is usually the case in high temperature work the selection of containers for the samples posed some problems. For vapor pressure studies tantalum crucibles, allowing little contact with the pressed samples, were used and some of the observations made during these experiments are pertinent to the study of the phase diagram. Most of the experiments, however, were performed in graphite containers, as were those of the previous authors. Two kinds of spectroscopic grade graphite crucibles were used. One was a % in. cylinder, 3/4 in. high, containing seven 3/16 in. holes drilled 1/2 in. deep into which were packed samples of the different mixtures weighing 250 to 500 milligrams. The other, consisting of separate crucibles, was prepared by drilling 3/16 in. holes, 1/2 in. deep into 1/4 in. graphite rods % in. long. The 7/8 in. cylinder was heated directly by induction while the small crucibles were packed in a tantalum heating element for induction heating. All heating was done in a high vacuum system in which the pressure was generally less than 1x10-5mm and never rose above 2x10-5mm when the samples were hot. The general pattern of the heating in graphite was to heat rapidly to a temperature somewhat below the desired one, then to raise the temperature slowly. The samples were held for 2 to 5 min at the maximum temperature, which in all cases was far higher than that needed to produce reaction. The short time was employed to reduce possible contamination by the crucible material and to reduce composition changes that would occur because of vaporization. After examination following the heating, the samples were reheated to a higher temperature. Temperatures were measured with a Leeds and Northrup disappearing filament optical pyrometer, certified by the National Bureau of Standards, by sighting through a window at the top of the vacuum

Jan 1, 1954

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na&apos; activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - &apos;Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By I. Havenaar

EXPERIMENTAL DATA In an article by C. K. Ferguson and J. A. Klotz,1 experiments on the filtration of drilling muds under borehole conditions are discussed. Experimental data on mud filtration through the wall and the bottom of the hole are presented. From the data on bottom-hole filtration it was concluded that the filtrate does not flow freely into the formation, but that the pores of the formation are plugged by the mud. A quantitative interpretation of the data can be civen, by using a formula for bottom-hole filtration, dehved below. This formula is based on the following assumptions, 1. Each time a blade of a drag bit, or a cone of a roller bit, moves along the bottom of the hole, the mud cake is completely removed. 3. A new mud cake is immediately formed on the freshly produced surface, and losses of "whole" mud into the formation are negligible (this is equivalent to an immediate plugging of the pores). 3. The filtration of the mud on the bottom of the hole follows the classic law: V = A +1—(Eq. I), where t is the time required to yield a volume of filtrate V, A is the surface area of filter cake, and C is a constant. The application of this equation means that any eroding effect of the mud stream on the mud cake is neglected. The formula for the calculation of the volume of filtrate, Q,, flowing in one second through the hole bottom (diam. d cm), when using a bit with n cones or blades rotating at a rate of rn revolutions per second, is derived as follows: The mud cake is formed on the bottom of the hole in the time t =1; the filtrate volume V which passes n through the bottom In this time 1s given by Eq. 1: After1/nmsec the mud cake is removed. In one m second this process takes place nm times. Therefore the volume of filtrate, obtained in one second is given by This equation has now been applied to the experiments of Ferguson and Klotz. The constants C were derived by means of Eq. 1 from the API filter losses of the muds used by the authors (t = 1,800 sec; A = 45.16cm2). A three-cone bit was used (n = 3) at 90 rpm (m = 1.5). The calculated figures are compared with the experimental data in the table below. The calculated values of Q, are usually lower than the experimental values. This may be due to the following causes. 1. The value of C used in the calculation is based on the API filter test (filtration pressure of 100 psi), whereas the experimental data were obtained with a filtration pressure of 200 psi. Although the effect of the pressure on C is not large, C decreases somewhat with increasing pressure, and this leads to a higher filtration rate. 2. Mud losses and the eroding action of the mud stream on the cake are not entirely negligible. 3. The values of Q, derived by Ferguson and Klotz from their experiments are too high, because of their assumption that all pore liquid within the formation drilled is picked up by the drilling mud. It is found, however, that the calculated values of Qf, except in the case of oil base muds, are of the right order of magnitude. ACKNOWLEDGMENT The author wishes to thank the management of the Koninklijke/Shell-Laboratorium, Amsterdam, for permission to publish this note.

Jan 1, 1957

By F. W. Schremp, V. L. Johnson

This paper discusses the results obtained from high temperature, high pressure filter loss studies in which field samples of clay-water, emulsion, and oil base fluids were used. High temperature, high pressure tests of some premium priced emrilsion and oil base drilling fluids show filter loss peculiarities that are not predicted by standard API tests. It is recommended that high temperature, high pressure filter loss tests be used to evaluate the performance of such fluids. Apparatus is described which proved to be satisfactory for evaluating filter loss behavior over a wide range of temperatures and pressures. INTRODUCTION The petroleum industry spends large sums of money each year on chemical treating agents for lowering filter loss and on premium-priced low filter loss drilling fluids. While it is an accepted fact that low filter loss is advantageous during drilling operations, it is questionable whether the present standard method of determining filter loss gives a reliable indication of the loss to he expected under bottom hole conditions. The purpose of this paper is to show that high temperature. high pressure filter loss tests Should be used to evaluate filter loss behavior of fluids for deep drilling. Concern over possible effects of filter loss on oil well drilling and well productivity dates back to the early 1920&apos;s. During the years 1922 to 1924, filtration studies were reported by Knapp,&apos; Anderson2 and Kirwan." These studies were the first to be reported in the literature on this subject. No further information was published on the subject until 1932 when Rubel&apos; presented a paper in which he discussed the effect of drilling fluids on oil well productivity. In 1935. .Jones and Babson constructed the first laboratory tester designed to study the effects of temperature and pressure on the filter loss behavior of clay-water drilling fluids. In a discussion of their investigations, Jones and Babsons stated, "Performance characteristics of a mud can he evaluated with considerable reliability by a single test at 2,000 psi and 200°F. Exact correlation between the results of performance test5 made under these conditions and the behavior of muds in actual drilling operations is of course impossible." Jones arid Babson apparently were well aware that at best laboratory tests can give only qualitative answers to the question of what is the actual behavior of a drilling fluid when subjected to deep drilling conditions. Jones&apos; presented a paper in 1937 in which he described a static filter loss tester to be used for routine filter loss tests. This instrument subsequently was adopted as the standard APl filter loss tester. In 1938, Larsen7 developed a relationship between filtrate volume and filtrate time that is in general acceptance today. Larsen was cognizant of the danger of estimating bottom hole behavior from filter loss measurements at room temperature. He tried to predict the effect of temperature on filter loss by relating temperature effects through the temperature dependence of filtrate viscosity. This was undoubtedly an over-sirriplification of the temperature dependence of drilling fluid filter loss. In 1940, Byck" published a summary of experimental results of filter loss tests made on six representative California clsy-water drilling fluids. He concluded that "no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied." Byck&apos;s findings were presuma1)ly well accepted and recognized by drilling Fluid technologists, and yet, they did not lead to wide adoption of high temperature drilling fluid filtration equipment. This is evidenced by the fact that no addition information has appeared in print on the subject since 194). Study of Byck&apos;s data shows that there was a useful consistency in them. The fluids did not show predictable losses at high temperatures, but they did line up at high temperatures in approximately the same order that they lined up at low temperatures. That is, if a fluid appeared to be a good fluid with relatively low loss at low temperatures, it would also be a good fluid with relatively low loss at high temperatures. In the last decade. the above situation has changed. The drilling fluid art is markedly different from what it was. The outstanding change, as far as the present discussion is concerned, has been the adoption of wholly new types of drilling fluids. Oil base and emulsion drilling fluids have come in to wide use. It is, therefore, necessary- to re-examine previously satisfactory generalizations to see if they are still valid. It turns out. as might have been expected. that Byck&apos;s explicit generalization. already quoted, is still true. Filter losses at high temperatures cannot be predicted from filter losses at low temperatures. However, no further generalizations are valid now. Fluids of different chemical types show different general behaviors. No longer do the fluids line up approximately the same at high temperatures as they do at low temperatures. They may line up entirely differently. Special fluids exhibiting very low loss at low temperatures may have losses as high as those of ordinary clay-water fluids at high temperatures. This fact is highly significant, because premium prices are being paid for the special fluids.

Jan 1, 1952

By H. S. Ten Eyck

Fertilizer normally is spoken of as having three main components: nitrogen, phosphorus and pot- ash. Certainly, however sulfur must also be considered a basic component of fertilizers, even though in many instances it does not end up as a part of the end product. In addition, with heavier cropping and the resultant drain of plant foods from the soil, we have now reached a point where the minor elements necessary for plant growth have become a major factor in the fertilizer industry.

Jan 7, 1967